Search results

Create the page "Effects loop" on this wiki! See also the search results found.

• FX Loop block
  =About the FX Loop block (FXL)= The I/O 2 loop on the Axe-Fx II and AX8 can operate as an effects loop: FX Send (Output 2) and FX Return (Input 2). Alternatively, Input 2 and Out
  6 KB (1,108 words) - 14:50, 5 February 2024
• Send and Return blocks
  =Use Send/Return to create a feedback loop= You can use the Send/Return blocks to create a feedback loop with a Delay block.
  4 KB (573 words) - 11:44, 9 April 2024
• Output block
  ...M9 and FM3, an Output block can also operate as Effects Send in an effects loop. See below. =Effects loop=
  4 KB (701 words) - 14:46, 2 March 2024
• Looper block
  ...he Looper is a dedicated effect block, providing minutes of stereo or mono loop time. The FM3, FM9 or FC-6/FC-12 provide dedicated Looper controls. Wikipedia's [http://en.wikipedia.org/wiki/Loop_(music) Loop (music)] article has more information.
  10 KB (1,661 words) - 16:50, 16 April 2024
• Input block
  ...9 and FM3, an Input block can also operate as Effects Return in an effects loop. See below. =Create an effects loop=
  11 KB (1,636 words) - 00:18, 3 March 2024
• Comparing the Axe-Fx II, AX8 and FX8
  =List of effects per device= Read this: [[Effects list]]
  14 KB (2,317 words) - 19:44, 15 February 2024
• FX8
  <font color=red>The FX8 (amp modeler and multi-effects pedalboard) has been discontinued. This page will not be updated.</font> The FX8 provides effects for the gigging musician who uses his own amp(s) and cabinet(s), including
  33 KB (5,417 words) - 00:24, 3 January 2024
• Comparing the Axe-Fx III to the Axe-Fx II
  '''Effects''' * The output level of some effects / effects types has been changed, such as Resonator and Studio Compressor
  10 KB (1,519 words) - 17:47, 16 April 2024
• AX8
  <font color=red>The AX8 (amp modeler and multi-effects pedalboard) is discontinued. This page will not be updated.</font> * [http://www.fractalaudio.com/ax8-amp-modeler-multi-effects Website]
  26 KB (4,192 words) - 00:35, 3 January 2024
• Setup menu
  ==[[Presets#Global_Effects_Mix|Effects Mix]]== Usually you will use this when you send the effect loop out before the amp block. The signal will be weak going to the D/A converte
  18 KB (2,979 words) - 16:07, 16 April 2024
• Firmware release notes - FX8
  ...laced before Amp. Use “Line” when compressor is placed in the amp’s effect loop. .... This no longer changes which effects are in your preset, or the order of effects. THEREFORE, you must first insert an effect before it can be assigned to a
  23 KB (3,724 words) - 00:37, 2 January 2024
• Zery uninteresting wiki sandbox
  ...en guitar and amp. The amp’s distortion follows the wah effect. Many other effects fall in this same category. ...amp. If you wanted to produce this natural sounding reverb or delay, these effects would likely be run “POST.” This is not to say that delay or reverb bef
  30 KB (5,012 words) - 20:10, 7 April 2024
• Presets
  ...Scenes]] are like your traditional pedalboard at a particular moment, with effects on or off and set to a specific channel. * Effects in front of Amp and Drive blocks should not be set to stereo. Certain effec
  64 KB (10,468 words) - 23:06, 18 April 2024
• Reverb block
  ...NNEL : A natural reverb in a long, narrow space tunnel, great for special effects. [https://forum.fractalaudio.com/threads/effects-quality.75657/#post-924391]
  29 KB (4,411 words) - 16:12, 16 April 2024
• I/O connectivity and levels
  ; Instrument level : The output level of guitars, basses etc., and effects pedals. ...[http://forum.fractalaudio.com/threads/setting-output-levels-for-external-effects.139722/#post-1656827] -10 dBV is compatible with instrument levels.
  155 KB (25,257 words) - 16:49, 16 April 2024
• RJM Mastermind MIDI foot controller
  ...Axe-Fx), separately from bidirectional MIDI, but beware of creating a MIDI loop. ...Axe-Fx), separately from bidirectional MIDI, but beware of creating a MIDI loop.
  41 KB (7,191 words) - 00:49, 3 January 2024
• Firmware release notes - FM9
  ...so has the advantage that the wet level is controlled by the global Reverb/Effects Mix, if desired. * Delayed audio data for effects no longer on the routing grid after a preset change are cleared regardless
  50 KB (7,888 words) - 18:24, 15 April 2024
• Cab block
  In the <q>real</q> analog world, it makes a difference where you put effects, either before or after the speaker cabinet. It's different with digital pr ...and flanger the difference isn't very pronounced. For highly time-variant effects, like pitch shifting, the difference can be marked.
  86 KB (13,616 words) - 11:55, 23 April 2024
• Axe-Fx III, FM9 and FM3
  ...tion. It's primarily intended to be a standalone solution with a single fx loop. For amp integration or multiple loops we recommend the FM9 and Axe-Fx III. ...This is a portable client-server architecture that allows easy porting of effects and models between hardware platforms. When we ported the Axe-Fx III models
  75 KB (11,235 words) - 23:18, 20 April 2024
• Firmware release notes - Axe-Fx III
  ...so has the advantage that the wet level is controlled by the global Reverb/Effects Mix, if desired. Fixed wrong FX loop recovery gain in Suhr Badger models.
  134 KB (21,544 words) - 17:43, 19 April 2024

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)