Search results

Create the page "Connect" on this wiki! See also the search results found.

• FX Loop block
  * connect an additional instrument ...block). Make sure that the FX Loop block is connected to the Output block. Connect OUT1 to the FOH / FRFR etc., and OUT2 to the power amp. Use the OUT 1/2 kno
  6 KB (1,108 words) - 14:50, 5 February 2024
• Fractal-Bot
  * To connect Fractal-Bot to your computer, you may need to install a '''driver''' for yo ==Connect==
  5 KB (686 words) - 00:35, 27 February 2024
• BandHelper and Set List Maker
  =Connect= Connect a tablet or smartphone to the other device. The required cable/hardware dep
  5 KB (851 words) - 20:53, 17 February 2024
• X-Load LB-2 Reactive Load Box
  ...is a load box, that allows using a traditional tube amp without having to connect a speaker cabinet, therefore enabling silent playing. It passes and process The LB-2 features a Speaker Thru jack so you can connect a real speaker while also feeding line signal to a recorder or speaker simu
  16 KB (2,470 words) - 12:36, 8 April 2024
• Mono and stereo signal
  ...t that mono signal is produced at both the left and right jacks so you can connect to two monitors. To switch to dual mono, go to Setup > I/O > Audio and set * Connect only the left or right output to the amplification system or mixer, or
  5 KB (844 words) - 22:53, 1 March 2024
• IR Capture
  # Connect the line output of your mic preamp to Input 2 Left. # Connect a DI box between the amplifier output and speaker input. Be sure to use a D
  13 KB (2,036 words) - 00:39, 4 April 2024
• Expression pedals and external switches
  ==Connect a pedal== # Insert a Pitch block, directly above or below the Wah in a parallel row. Connect it back to the main row.
  14 KB (2,330 words) - 22:25, 29 March 2024
• Tone Match block
  # Connect the guitar to the input of the Axe-Fx II. # Connect Output 2 Left to the input of the amplifier being matched.
  21 KB (3,490 words) - 17:23, 8 April 2024
• Realtime Analyzer block
  # Connect an instrument cable from Output 3 (left or right) to the Instrument Input.
  3 KB (494 words) - 15:58, 16 April 2024
• Digital I/O and computer audio
  To connect the SPDIF port to an optical port, a SPDIF-to-TOSLINK adapter is required. To connect an FM3 or FM9 to the Axe-Fx III:
  25 KB (3,935 words) - 17:02, 16 April 2024
• RJM Mastermind MIDI foot controller
  ==Connect GT to Axe-Fx III== Connect the GT and Axe-Fx III with MIDI cables. Alternatively, the GT/22 lets you u
  41 KB (7,191 words) - 00:49, 3 January 2024
• MFC-101 MIDI foot controller
  Do NOT connect the adapter to the MFC simultaneously with Ethernet, Ethercon or an XLR cab ...MIDI cable is required. All pins must be wired (pins 6 and 7 carry power). Connect the 9VAC adapter to the phantom power input at the rear of the Axe-Fx (the
  32 KB (5,363 words) - 17:42, 12 January 2024
• USB
  The USB 2.0 protocol is used to connect the device to a computer and to run software for data transfers and MIDI-ov You can connect the Axe-Fx III and FM9 directly to an iOS device such as an iPhone or iPad.
  27 KB (4,137 words) - 13:29, 8 April 2024
• Synth block
  # Add a Synth block and connect it to the grid output.
  5 KB (790 words) - 11:45, 9 April 2024
• FASLINK
  Do NOT connect a power supply to the MFC-101 when using FASLINK.
  7 KB (1,087 words) - 21:47, 25 February 2024
• Wah block
  You need an expression pedal. Always connect the expression pedal with a TRS to TRS <q>stereo jack</q> cable. Read <q>[[
  7 KB (1,086 words) - 16:06, 16 April 2024
• Editors
  =Install and connect= ==Connect==
  73 KB (11,918 words) - 12:58, 18 April 2024
• Input block
  The [[Multiplexer block]] can connect directly to a physical input port, without needing an Input block inbetween
  11 KB (1,636 words) - 00:18, 3 March 2024
• Cab-Lab
  ...in real-time. This allows you to mix and monitor in real time. It doesn’t connect to Fractal Audio hardware directly, but it offers the capability to export
  9 KB (1,425 words) - 22:17, 9 March 2024
• MIDI
  ...MFC­‐101 at the [[FASLINK]] port, do not use the MIDI THRU port. Instead, connect downstream devices to the MIDI OUT port and set MFC ECHO TO MIDI OUT to “ ...a wireless MIDI adapter, or the Apple Lightning-to-USB Camera Adapter, to connect the Axe-Fx III or FM9 directly to an iOS device. This lets apps such as [[B
  43 KB (6,811 words) - 05:58, 1 March 2024

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)