Search results

Create the page "Connect" on this wiki! See also the search results found.

• FAMC Liquid Foot+
  ...a 7 pin MIDI cable with Phantom Power more than 1A (1000ma), '''DO NOT''' connect the power adapter to the Axe-Fx II Phantom Power Port because it will damag ...29 Specifications (Axe-Fx II XL+) Phantom power: female 2.5mm jack, do not connect adapters with a rating higher than 1A (1000ma)]
  125 KB (20,342 words) - 08:20, 25 March 2022
• Phaser block
  :Put the effect before the Amp block for best results, connect a pedal or switch to the Rate parameter to control speed, and turn Mix to 1
  14 KB (2,229 words) - 18:17, 16 April 2024
• I/O connectivity and levels
  ...or in an amp's effects loop) or when using the Four-Cable-Method (4CM) to connect to a guitar amplifier. ...r Cable Method (<q>4CM</q>), for <q>guitar level</q> input devices, and to connect to amplifiers and other purposes. In other words, use these ports as an add
  155 KB (25,257 words) - 16:49, 16 April 2024
• Scenes
  * Pedal jack: connect a momentary switch to the rear of the unit. In I/O > CTRL set Scene Increme
  18 KB (3,060 words) - 09:09, 6 May 2024
• Setup menu
  ...t that mono signal is produced at both the left and right jacks so you can connect to two monitors. To switch to dual mono, go to [[Setup menu|I/O > Audio]] a
  18 KB (2,979 words) - 16:07, 16 April 2024
• FC-6 and FC-12 foot controllers
  ...12 to it. So for small gigs/rehearsals use the FM-3 alone. For larger gigs connect an FC (or two).
  27 KB (4,240 words) - 16:52, 16 April 2024
• Cab block
  * Connect Axe-Fx III / OUT2 LEFT to FM3 / IN2 LEFT * Connect FM3 / OUT2 LEFT to Axe-Fx III / IN2 LEFT
  86 KB (13,616 words) - 11:55, 23 April 2024
• MIDI SysEx
  :::Bit 0: connect row 1 to effect input :::Bit 1: connect row 2 to effect input
  114 KB (16,586 words) - 23:11, 24 December 2023
• AX8
  The pedal ports let you connect expression pedals and/or external switches.
  26 KB (4,192 words) - 00:35, 3 January 2024
• FX8
  The pedal ports let you connect expression pedals and/or external switches.
  33 KB (5,417 words) - 00:24, 3 January 2024
• Zery uninteresting wiki sandbox
  # Add a Synth block and connect it to the grid output.
  30 KB (5,012 words) - 20:10, 7 April 2024
• Axe-Fx II
  * Phantom power: female 2.5mm jack, do not connect adapters with a rating higher than 1A (1000ma)
  33 KB (5,066 words) - 10:51, 27 February 2024
• Firmware release notes - Axe-Fx II
  *# Connect the line output of your mic preamp to Input 2 Left. *# Connect a DI box between the amplifier output and speaker input. Be sure to use a D
  194 KB (31,845 words) - 17:59, 14 February 2024
• Axe-Fx III, FM9 and FM3
  The pedal ports let you connect expression pedals and/or single or dual external switches directly to the d
  75 KB (11,235 words) - 23:18, 20 April 2024
• Amplifier models list
  ...ating cab for a BE/HBE is 16 ohms which means lots of feedback. But if you connect the amp to an 8 ohm load there is about 30% less feedback. The amp will sou ...is a triode. When you run a pentode (or beam tetrode) in triode mode you connect the screen to the anode which effectively defeats the screen. This lowers t
  282 KB (42,650 words) - 16:03, 19 April 2024
• Firmware release notes - Axe-Fx III
  ...n a Volume block. For example, if you use CC #23 as External Control 1 and connect that to the Volume 1 block in all your presets then set this to 23. Likewis
  134 KB (21,574 words) - 17:34, 2 May 2024
• Drive block
  ...RCA 2N270 devices, powered by two 1.5-volt batteries, and a lead cable to connect it to an instrument (bass as it was originally intended, or guitar). German
  264 KB (42,788 words) - 13:40, 18 April 2024
• Amp block
  When you run a pentode (or beam tetrode) in triode mode you connect the screen to the anode which effectively defeats the screen. This lowers t
  431 KB (68,296 words) - 14:58, 20 April 2024

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)