Read the Owners Manual first!

Difference between revisions of "IR Player block"

From Fractal Audio Wiki
Jump to navigation Jump to search
 
(129 intermediate revisions by 2 users not shown)
Line 1: Line 1:
−
<font color=red>Note: this block has been announced but has not yet been implemented!</font>
 
−
 
 
__TOC__
 
__TOC__
  
−
=Available on which Fractal Audio products=
+
=Available on which products=
  
 
* '''Axe-Fx III''': 2 blocks
 
* '''Axe-Fx III''': 2 blocks
−
* '''Axe-Fx II''': n/a
+
* '''VP4''': 1 block
−
* '''AX8''': n/a
+
* '''FM3''', '''FM9'''
−
* '''FX8''': n/a
+
* '''Axe-Fx II''', '''AX8''', '''FX8''': no
 +
 
 +
=Channels or X/Y=
 +
 
 +
* '''Axe-Fx III''', '''VP4''': 4 channels
 +
 
 +
=About the IR Player=
 +
 
 +
The IR Player block processes up to two [[Impulse responses (IR)|impulse responses]], has less features than the [[Cab block]] and therefore requires less CPU. It can also process [[Tone Match block]] data that has been exported as an IR. This makes it the first choice to run an impulse response of a device such an acoustic guitar or a preamp.
 +
 
 +
You can also use it for room ambience because the IR Player supports FullRes IRs.
 +
 
 +
It also get used for room EQ correction.
 +
 
 +
Read these pages for more information:
 +
* [[Impulse responses (IR)|Impulse Responses (IRs)]]
 +
* [[Cab block]]
 +
* [[Tone Match block]]
 +
* [[IR Capture]]
 +
* [[Cab-Lab]]
 +
 
 +
<blockquote>
 +
'''FRACTAL AUDIO QUOTES'''
 +
<HR>
 +
<blockquote>
 +
[https://forum.fractalaudio.com/threads/axe-fx-firmware-release-version-17-01-release.178095/post-2170002]
 +
The IR Player block does not attempt to normalize the volume as it is a generic convolution player and doesn't know whether the IR is a cabinet IR or some other type of IR (i.e., reverb, violin, etc.).
 +
</blockquote>
 +
</blockquote>
  
−
=X/Y and channels=
+
==IR Player on the VP4==
  
−
* '''Axe-Fx III''': 4 channels
+
An IR Player block has been added to the VP4. This lets you load [[Impulse responses (IR)]]. An IR can recreate the tone of a guitar speaker cabinet, and also works for acoustic body modeling and other creative applications. The IR Player can handle up to two IRs. The VP4 lets you store 256 IRs on the hardware. These can be managed via “Manage Cabs” or Fractal-Bot in VP4-Edit. Muting an IR saves CPU.
−
* '''Axe-Fx II''': n/a
 
−
* '''AX8''': n/a
 
−
* '''FX8''': n/a
 
  
−
=What is the IR Player=
+
To send one mono output with an IR to FoH and another to a stage amp and cab, do this: [https://forum.fractalaudio.com/threads/vp4-firmware-v3-00-public-beta-2.214457/#post-2691167]
 +
# Make sure the IR player is last in the chain.
 +
# Add an IR in the first slot of the IR Player and pan it hard left.
 +
# Load a totally flat or 'null' IR in the second slot and pan it hard right. [https://forum.fractalaudio.com/threads/vp4-firmware-v3-00-public-beta-2.214457/#post-2691167 You can find such an IR here]
  
−
This is a block dedicated to processing a single IR. It's exclusive to the Axe-Fx III.
+
=IR Player block diagram=
  
−
It can operate as a simplified version of the Cab block.
+
[[image:IR Player block.png|550px]]
  
−
It also lends itself to processing Tone Matches of instruments and devices, which have been exported as IRs, such as acoustic guitars and preamps.
+
=Parameters=
  
−
Read more about:
+
The IR Player supports two IRs with individual LEVEL and PAN controls for each IR.
  
−
* [[Cab_block_and_IRs#Impulse_responses_.28IRs.29|Impulse Responses]]
+
A MIX control is also provided so the block can be used as a convolution reverb.
−
* [[Cab block and IRs|Cab block]]
+
 
−
* [[Tone Match block]]
+
The MODE parameter selects between Parallel and Series. When in series, the individual level and pan controls are defeated and removed from the UI. The volume is consistent if MODE is set to Parallel and only one IR is being used.
 +
 
 +
Choices for IR LENGTH are Off, 256, 512, 1024 and Max. Setting IR LENGTH to OFF defeats the IR.
 +
 
 +
[[Impulse_responses_(IR)#IR resolution|IR resolution]] has more information.
 +
 
 +
 
 +
[[image:slope.gif|500px]]
 +
 
 +
=Tips, tricks and troubleshooting=
 +
 
 +
==No Global blocks==
 +
 
 +
The IR Player doesn't support [[Global blocks]].
 +
 
 +
==Phase correction==
 +
 
 +
<blockquote>
 +
'''FRACTAL AUDIO QUOTES'''
 +
<HR>
 +
 
 +
<blockquote>
 +
[https://forum.fractalaudio.com/threads/as-designed-exported-ir-from-tma-out-of-phase-and-9-db-level-difference.154000/post-1830563]
 +
The Cab and IR Player blocks automatically "phase correct" IRs so that the peak signal is positive.
 +
</blockquote>
 +
 
 +
<blockquote>
 +
[https://forum.fractalaudio.com/threads/phase-correct-switch-for-tma-irp-cab-to-fix-ir-phase-cancellations.154005/post-1831184]
 +
When an IR is read from storage the first few hundred samples are scanned and the maxima is found. If the maxima is a negative value the polarity of the IR is inverted because it is assumed the polarity of the IR was inverted when captured. This can happen if the speaker is wired backwards, the IR is captured from the back of the cabinet, the back of a ribbon mic is used, or a polarity inversion occurs in the power amp or mic preamp.
 +
</blockquote>
 +
</blockquote>
  
−
=Parameters table=
+
=Videos=
  
−
{| class="wikitable"
+
Watch the videos on the [[Impulse_responses_(IR)#Videos|Impulse Responses page]] for more information.
−
|-
 
−
! '''Parameter'''
 
−
|-
 
−
| Bank
 
−
|-
 
−
| Number
 
−
|-
 
−
| Low Cut, High Cut
 
−
|-
 
−
| Filter Slope
 
−
|-
 
−
| Mode
 
−
|-
 
−
| Input Mode or Input Select
 
−
|}
 
  
 
[[category:Axe-Fx3]]
 
[[category:Axe-Fx3]]
 
[[category:Sounds]]
 
[[category:Sounds]]
 +
[[category:All]]

Latest revision as of 20:00, 24 July 2025

Available on which products

  • Axe-Fx III: 2 blocks
  • VP4: 1 block
  • FM3, FM9
  • Axe-Fx II, AX8, FX8: no

Channels or X/Y

  • Axe-Fx III, VP4: 4 channels

About the IR Player

The IR Player block processes up to two impulse responses, has less features than the Cab block and therefore requires less CPU. It can also process Tone Match block data that has been exported as an IR. This makes it the first choice to run an impulse response of a device such an acoustic guitar or a preamp.

You can also use it for room ambience because the IR Player supports FullRes IRs.

It also get used for room EQ correction.

Read these pages for more information:

FRACTAL AUDIO QUOTES

[1] The IR Player block does not attempt to normalize the volume as it is a generic convolution player and doesn't know whether the IR is a cabinet IR or some other type of IR (i.e., reverb, violin, etc.).

IR Player on the VP4

An IR Player block has been added to the VP4. This lets you load Impulse responses (IR). An IR can recreate the tone of a guitar speaker cabinet, and also works for acoustic body modeling and other creative applications. The IR Player can handle up to two IRs. The VP4 lets you store 256 IRs on the hardware. These can be managed via “Manage Cabs” or Fractal-Bot in VP4-Edit. Muting an IR saves CPU.

To send one mono output with an IR to FoH and another to a stage amp and cab, do this: [2]

  1. Make sure the IR player is last in the chain.
  2. Add an IR in the first slot of the IR Player and pan it hard left.
  3. Load a totally flat or 'null' IR in the second slot and pan it hard right. You can find such an IR here

IR Player block diagram

IR Player block.png

Parameters

The IR Player supports two IRs with individual LEVEL and PAN controls for each IR.

A MIX control is also provided so the block can be used as a convolution reverb.

The MODE parameter selects between Parallel and Series. When in series, the individual level and pan controls are defeated and removed from the UI. The volume is consistent if MODE is set to Parallel and only one IR is being used.

Choices for IR LENGTH are Off, 256, 512, 1024 and Max. Setting IR LENGTH to OFF defeats the IR.

IR resolution has more information.


Slope.gif

Tips, tricks and troubleshooting

No Global blocks

The IR Player doesn't support Global blocks.

Phase correction

FRACTAL AUDIO QUOTES

[3] The Cab and IR Player blocks automatically "phase correct" IRs so that the peak signal is positive.

[4] When an IR is read from storage the first few hundred samples are scanned and the maxima is found. If the maxima is a negative value the polarity of the IR is inverted because it is assumed the polarity of the IR was inverted when captured. This can happen if the speaker is wired backwards, the IR is captured from the back of the cabinet, the back of a ribbon mic is used, or a polarity inversion occurs in the power amp or mic preamp.

Videos

Watch the videos on the Impulse Responses page for more information.

Retrieved from "https://wiki.fractalaudio.com/wiki/index.php?title=IR_Player_block&oldid=93123"