Difference between revisions of "Main Page"

From Fractal Audio Wiki
Jump to navigation Jump to search
(5.18 Ultra/Std)
(5.19 Ultra/Std)
Line 77: Line 77:
 
* [http://www.axechange.net Axe-Fx Patch exchange website]
 
* [http://www.axechange.net Axe-Fx Patch exchange website]
 
* [http://www.musicgearsource.com/fractal.html Interview with Cliff Chase about the Axe-Fx]
 
* [http://www.musicgearsource.com/fractal.html Interview with Cliff Chase about the Axe-Fx]
* [http://fractalaudio.com/Documents/axefx5_18.zip Latest Standard Firmware (5.18)]
+
* [http://fractalaudio.com/Documents/axefx5_19.zip Latest Standard Firmware (5.19)]
* [http://fractalaudio.com/Documents/ultra5_18.zip Latest Ultra Firmware (5.18)]
+
* [http://fractalaudio.com/Documents/ultra5_19.zip Latest Ultra Firmware (5.19)]
 
* [http://axechange.net/editorbeta.aspx Axe-Fx PC/Mac Editor Beta]
 
* [http://axechange.net/editorbeta.aspx Axe-Fx PC/Mac Editor Beta]
 
* [http://fractalaudio.com/Documents/ir2syx.zip IR2Sysex Utility]
 
* [http://fractalaudio.com/Documents/ir2syx.zip IR2Sysex Utility]

Revision as of 21:49, 24 June 2008

Welcome to the Axe-Fx Wiki

the user manual that anyone can edit, and don't forget it was ACWILD's idea!

Fractal Audio Axe-FX

  Content · Axe-Fx Wiki Manual · Tips · FAQ · Tutorials · Help


Introduction

Welcome to the Axe-Fx Wiki. This site contains many helpful hints, tips, descriptions, FAQs and other user contributed material for Fractal Audio Systems Axe-Fx and Axe-Fx Ultra pre-amp/effects processors.


The compilation of resources and online manual in the Axe-Fx Wiki, aim to expand on the official user manual provided by Fractal Audio Systems. You can help expand the Axe-Fx Wiki by creating a user account. It's easy to join and start contributing.


Random Tip
 Random Tip: {{#random:



Press and hold ENTER to automatically place and route shunts from the current position to the output mixer.


Each time EDIT is pressed, the next effect edit page is displayed. If you are on a different page, the edit page for the nearest effect will be displayed.


Hold down BYPASS to restore all parameters of an effect block to default.


Each time ENTER is pressed while in the sequencer menu, a new random set of values is loaded. You can use this feature to find cool sequence patterns.


The "bright switch" of an amp block may be enabled by selecting the TREB control and pressing ENTER. This will toggle the state of the Bright Switch. The text “BRT” will appear under the control when the bright circuit is active.


The "boost switch" of an amp (which adds 12db of gain) may be enabled selecting the DRIVE control and pressing ENTER. This will toggle the state of the Boost switch. The text “BOOST” will appear under the control when the boost circuit is active. The boost switch adds 12db of gain to the amp simulation. This is useful to get more drive out the amp than it would normally have.


In addition to copying effects block parameters, the controller parameters can also be copied (i.e, Envelope, ADSR, LFO, etc) from one preset to another. Just press the RECALL button, page over to the EFFECT tab, select the proper preset to copy from, then select controller from the Retrieve area.


You can use the feedback send and return to extend the length of a chain if necessary.


On units built prior to mid-July 2007 the serial number is underneath the main-board. The serial number is now located on the back next to the AC inlet.


One thing to try is to use a blend of two amps into one cab. This will save a small measure of CPU (~10%?).


With the power amp simulation off, the depth and deep controls are deactivated; the master becomes a volume control and the presence controls turns into a shelving filter.


There's a secret menu on the Utility page accessible by pressing and holding the PAGE right button. WARNING! Be very careful with the the Clear SRAM and Test SRAM functions as they will completely wipe out all your presets!!! On firmware 4.02, the clock rate is now displayed and a TEST LEDS function has been added.


You can completely reset/initialize the contents of the edit buffer by holding RESET while the Axe-Fx boots.


To insert an effect block, place it at the end of the chain and move it to the desired location (using the MOVE page, MOVE LEFT command). All the other effect blocks will automatically be moved to the right.


To emulate the solo "BOOST" feature found on TC Electronics units, place a Mixer block at the end of your signal chain and attach an external controller to control the overall output gain (on page 2). Somewhere around 90% is pretty close to -6db which is the default on the TC Units.}}

Online manual links

Pages of Interest

Links of interest

Interesting Wiki stats and other

Contributing to the site

Getting Started

  • To edit or create new pages, please create a user account. It's easy to join and start contributing.
  • Submit a new entry
    • You can edit or create a page by using the box below

Quick Guidelines

  • Search first to see if a page already exists for the particular topic you want to write about. If the page already exists, add your entry to the existing pages to avoid redundancy.
  • Create redirection pages, so that if a user misspells or there's synonyms for a particular search term, the user is taken to a relevant page.
  • Always preview your edits before saving a page
  • Think about creating a new page for new additions and transcluding it into the place you want it displayed.
  • More information in How to Contribute.