Axe-Fx II FAQ

INTRODUCTION

This is a FAQ page for the Fractal Audio Axe-Fx II. It is not officially supported by Fractal Audio. The content mostly is derived from forum messages by Fractal Audio, Fractal forum administrators/moderators and other experienced users such as Matman, Javajunkie, Bakerman, Scott Peterson, Don Petersen, Rex, and lots of others.

If you're looking for tips and tricks regarding the Standard and Ultra (first-generation units), look here.

Keep an eye on the sources below for up-to-date information:

1. Fractal Audio website
2. Fractal Audio users forum
3. Axe-Fx Wiki
4. (...) Axe-Fx II manual
5. (...) Firmware release notes
6. Posts from the President of Fractal Audio

If you subscribe to this forum thread, you’ll receive notifications of important news like the release of new firmware.

Alexander van Engelen (Yek)

ABOUT THE AXE-FX II

What are the differences with Standard/Ultra

See AFXII Product Brief and the Fractal Audio website.

What are the technical specifications

See AFXII Product Brief.

How do the unit and the circuit board look

1. Circuit board
2. High resolution picture of the front panel
3. High resolution picture of the rear panel

Where is it manufactured

All units are made in USA. Source The units are identical for all global regions and support 100-240V.

What are the dimensions

19" x 3,5" x 14". An inch or two deeper than the Standard/Ultra. Source1 Source2 The depth according to the Product Brief is 12" but this is incorrect.

What poweramp and speakers are used to compare the amp models to the real amps

Cliff: "A Mesa 4x12 with my Carvin F1200 power amp. The patches were dry because I do A/B comparisons using an A/B box. I run the cab stereo and put the amp being modeled into one side and the Axe-Fx II into the other side. I run my guitar to the A/B box. One output to the amp and one to the Axe-Fx. Then I can quickly switch back and forth to verify the model is working properly." Source

Are the rack ears removable

Yes. Source

Can it be mounted in a rack or rackbag

The Axe-Fx is a 19” 2HE device. It can easily be mounted in a rack or rackbag. If necessary combined with a racked poweramp and/or power conditioner. You can put the rack or bag on a stand such as this or this.

CONNECTING TO A COMPUTER

Do I need a MIDI interface to connect to a computer

No, USB suffices (MIDI-over-USB). The AFXII itself is an USB-to-MIDI adapter. MIDI connections can still be used and editing over MIDI is still possible.

Do I need an audio interface to record

No. The AFXII already contains the required circuitry to send a digital signal into the computer over USB. If you're monitoring from the AFXII itself there's no latency. When monitoring the signal from the computer, the latency is determined by the host computer.

Which digital I/O connections are supported

1. S/PDIF (RCA coaxial)
2. AES/EBU (XLR)

Can I use the digital input simultaneously with analog inputs and outputs

You can use the digital input with analog Output 1 (and simultaneously digital out). You can use Input 2 and Output 2 while using the digital input. Source

Is the digital sample rate fixed

Yes, at 48kHz. Resampling is handled in software. Source1 Source2 Source3 Source4

How does it support USB

The USB is Audio Class 2.0 compliant. On a Mac you don't need to install any drivers but you do need to install the firmware loader for the USB chip (it is a "soft" processor and downloads its code from the host on start-up). On a PC you also have to install the Audio Class 2.0 drivers. The driver supports ASIO, SRC, etc. etc. You can use the USB just for remote control via Axe-Edit if you want. You don't have to use the audio features. Source

In the I/O > MIDI menu set "USB ADAPTER MODE" to ON and it functions as a USB-to-MIDI adapter. Source

You can edit and simultaneously record through USB. Source

It cannot connect to a USB stick. Source

The Axe-Fx will respond to MIDI events sent over USB. Source

How does the unit show up in my DAW

As a 3-In, 2-Out device. Source

Can I use it for reamping

The third channel on the USB output (to the computer) is the raw data from the Instrument Input. You record this. You then play this track back into the AFXII and set Input Source to USB. Then tweak until you get the sound you want. When you are happy, record the first two channels which are the processed audio. You can save the raw track if you want to go back later and reamp the track again. Source

The dry signal level is fixed, and for good reason. When you send that signal back in it is the same as the original signal sent to the grid. This means you don't have to adjust anything when reamping. You simply send the signal back. Source

USING AXE-EDIT

Where do I download Axe-Edit

Axe-Edit product page

Can I use Axe-Edit and the MFC-101 simultaneously

Yes. There's no need (anymore) to use a MIDI Merger.

Where do I find information about the upcoming Axe-Edit 1.0 release

Here.

SYSTEM, FIRMWARE

Where do I download the latest firmware

Fractal Support.

Which programming language is used to code the firmware

C and assembly. Source

How do backup and restore work

The AFXII contains onboard backup memory.

Does it have a memory slot

No.

Is it bad to switch the power off just like that

Use the front panel knob to switch the unit on or off. Or disconnect the power. As often as you want, it doesn't hurt. Just remember to store your preset changes first, it saves all other changes automatically.

CONNECTING INSTRUMENTS AND AMPS

How do I use it with FR amplification

(tube / ss poweramp)

How do I use it with my own preamp or amplifier (4CM)

The AFXII supports unity gain when settings things up for 4CM: Four Cable Method. To obtain unity gain turn both Output knobs at the front fully up. Source

How do I connect my guitar(s)

The front panel input uses a proprietary circuit and dedicated A/D converter for low noise. Always use the front input for guitar, whether wired or wireless. Source

The front input does not disable the rear input (different from Standard/Ultra). Use the menu to select either the front or the rear for Input 1. You can leave everything plugged in. Source

The front input impedance is 1 Mohm, or less if Input Impdance is adjusted.

All rear analog inputs are balanced like the onboard XLR outputs.

How do I connect a wireless receiver

The same way as your guitar: fFront, to take advantage of the front input's "special sauce" for noise reduction. The rear inputs (both 1 and 2) operate on line level, the front input operates on instrument level.

How do I set the input levels

Instead of knobs at the front, there are soft Input knobs in the I/O menu. The input levels are controlled via digitally-controlled potentiometer. These work globally, not per preset. The setting doesn't affect the input gain of the Amp and Drive blocks. Source1 Source2

How does it obtain unity gain

The AFXII has digitally controlled potentiometers before and after the A/D and D/A converters. Therefore it knows what the input and output gains are. It compensates for these gains in the digital path. This allows "unity gain processing". If you set the Output Level knob to maximum you will get out what you put in (assuming the blocks have no gain). So if you were to make a preset with shunts from input to output and you put a 1V signal into the unit you would get 1V out. Source

How do the HumBuster outputs work

The 1/4" outputs have a "remote ground sense" feature. You take a TRS cable and on one end you put a TRS plug and on the other end you put a regular TS plug. On the TS end you tie the ring conductor to ground. Plug the TRS end into the Axe-Fx II. The ground noise of the attached equipment is sensed and added to the output signal thereby cancelling the common-mode noise (hum). This is especially useful when doing the 4CM since that's when you usually get the worst ground loops. Source

Can I connect a music player

Yes, connect the player to the USB slot. The signal will be mixed into the output of the AFXII. Adjust the volume on the player. Source

How do I set the headphones level

Use the Output1 knob. Source

How do I get rid of noise

See Noise Gate.

CREATING, EDITING AND USING PRESETS

How many presets does it support

384. Most are ported from the Ultra. Source1

Can I load Standard and Ultra presets

No. Source1 Source2

How does the DSP load compare to the Ultra

A patch that uses 94% of the DSP on an Ultra will use around 70% on the AFXII. Source

How fast does it switch between presets

About 20ms.

Does it have a Compare function for presets or effect blocks

No(t) yet. Source Alternatively you can set up two presets, use the X/Y function or use Axe-Edit's Snapshot to compare.

How do I use the Quick Control knobs

You can use them to quickly scroll through presets instead of using the Value Wheel. Source And they can be assigned to any modifiable parameter per patch. Source Or configure them to function as pedals. Source

What's the DIR tab on the main preset screen for

It lists preset names and numbers for quick recall. Source

How does Input Impedance work

It is a parameter in the layout menu that affects a hardware switch. It can be set to automatic (detects the appropriate setting based on your first effect) or you can set it manually. Source Its range is 70k - 1Meg. Source The input impedance is selectable from a dozen or so values. It is done right at the instrument input using analog switches. Source It changes based on the amp model, however amps are always 1 Meg. If the first active effect is a Drive, for example, the impedance will change based on the Drive model. Source It can be saved per preset. Source The impedance feature will only have an audible effect if you are plugging your guitar directly in. It operates by loading down the guitar's pickups. If you have anything buffering the guitar then you won't be loading the pickups. Source

What are Global Blocks

An effect block can be saved as a Global Block. It then can be linked to from other presets, just like Global Amps. A change to the "master" will affect all linked blocks.

Does it support spillover of delay trails and reverb between presets

Yes, in the same way as the 1st-generation units.

ABOUT EFFECTS IN GENERAL

How does the X/Y function work

1. You can set up certain effect blocks to switch between two sets of parameters. For example, with Amp blocks you can have 4 configured amps per preset, of which two can be active. Then use the X/Y knob on the AFXII, or an IA switch (toggle) on a MIDI foot controller, to switch between the sets. This essentially doubles the number of those blocks within a preset. X and Y can be the same type of effect, say a RAT drive, but with different parameters. There's no transition between the two. Switching occurs at block level using a MID CC, not on preset level. Source1 Source2 Source3 Source4 Source5 Source6
2. Cliff: "The idea behind X/Y is that people often have multiple distortion/chorus/delay/etc. pedals on their board but they rarely have more than one on at a time. So rather than creating more instances of effects, which sucks up CPU, have each instance capable of more than one sound." Source
3. X/Y switching is nearly instantaneous. Source
4. X/Y doesn't support spillover. Source
5. On the MFC-101 X is green, Y is Red. Source
6. The X and Y buttons also double as user-definable Quick-Jump keys, which can be set to open the EDIT menus of any 2 blocks without going through the grid.

Is there a Freeze or Hold effect

Yes, it's built into the Delay effect. Source

Does it have a Bit Crusher effect

No. Source

About Global EQ

It's always on. Source The 10-band frequencies are: 31, 63, 125, 250, 500, 1k, 2k, 4k, 8k, 16k. Source

AMP BLOCK

How many amp models can it hold

Lots. Source Each preset can have two Amp blocks. There's no impact on the DSP capacity because one of the two AFXII DSPs is devoted entirely to amp modeling. Each Amp block can also use the X/Y feature to switch between sets of parameters.

Can I rename the amp types

No. Source

How much DSP-capacity does an amp block require

One Amp block uses about 40%. One of the two DSPs is dedicated to Amp blocks. So you can run 2 of those. The other DSP is for other effects. Source

Does this amp modeling differ from Standard/Ultra

Yes. It's called G2 and Virtual Vaccuum Modeling modeling. See Fractal Audio website.

Where are the Warmth and Thump parameters

These are removed from the Amp block in the AFXII. Source

Where is the 8-band EQ positioned in the Amp block

It's fixed in position at the very output. Source

What are Global Amps

(...) It supports 10 Global Amps. You can save Amp block settings to a Global Amp slot without being in that slot already. Source

Do amps still have negative presence

No. However for amps with no negative feedback (damp at 0) it turns into a Hicut parameter. Source

How does Input Trim work

Changing the input trim doesn't affect the amount of distortion. This the whole idea. You set the trim to optimize the signal level into the converters. Internally the unit applies the inverse of the trim so that the signal into the grid is constant. In other words, if you put 1V into the input the input to the grid is 1V regardless of the trim setting. Source

What's the Saturation switch parameter for

It switches in a zener diode clipping stage right before the tone stack. This is the "Arrendondo Mod". Source

Are all amp parameters assignable to MIDI controllers

No. Cliff stated it now has the ability to do that for all parameters so maybe down the road. Source1 Source2

What about Standard/Ultra amp types that are not in the list (yet)

Cliff: "The amps I haven't ported yet are because I don't have the real amp yet. I could use theoretical values but I would rather not." Source

Javajunkie: "Plexi2 on Ultra = Plexi 1 w/ different bright cap val, xformer hi freq, and presence freq. I have the values written down. You can do the same with the Plexi normal on the II. From what I understand (and Cliff can correct if I am wrong) - Plexi 1 and 2 are the same models with different default values. Source

Cliff: "As for Eggie... It's just a Blues Jr. with no negative feedback." Source

Which amps are modeled

1. Below is the lst of modeled amps in the AFXII. Source
2. Cliff: "Almost all the amps in the AFXII are based on actual amps. The amps I haven't ported yet are because I don't have the real amp yet. I could use theoretical values but I would rather not." Source

59 BASSGUY

1. Real amp: Fender Bassman
2. Cabinet suggestion: ...
3. Original controls: Volume, Presence, Bass, Middle, Treble. Normal/Bright channel
4. For authentic tone: crank the Master, Drive at 3.50
5. Try with a Treble Booster Drive block
6. Fender tips in the Wiki
7. Wikipedia

65 BASSGUY

1. Cliff: "Definitely not your father's Bassman. Has a pissed-off Marshall vibe to it." Source

VIBRATO VERB

1. Real amp: Fender Vibroverb
2. Cabinet suggestion: ...
3. Original controls for Normal channel: Volume (no Master), Bass/Treble, Bright switch (on by default). The real amp also has a Bright channel
4. For authentic clean tone: crank the Master, Drive at 3.50. For more crunch turn up Drive
5. Wikipedia

PVH 6160

1. Cilff: "I have a block letter 5150 that I based the model on." Source

CAB BLOCK

How many cab slots does it have

64 factory (stock) cabs and 50 user cab slot for external IRs.

Which new parameters are added to the cab block

Room Level, Room Size, Mic Spacing, Low Cut and High Cut. Source

What are 2048-point IRs good for

Cliff: "Depends on the cab. Certain cabs benefit more than others. I started out with 8192 but didn't hear any difference so couldn't justify wasting all that space and CPU. You can hear it with room mics but the room simulation sounds nearly identical. There are a couple reasons for 2048. Probably most important is that it allows 1024 in stereo mode. To be able to do stereo 1024 requires a 2048 convolution engine. Secondly, some IRs benefit from longer IRs. Better to have the ability and not need it than the converse." Source1 Source2

A stereo cab (LoRes) now uses two 1024 IRs (instead of 512 on Standard/Ultra). Source

Jay Mitchell's comments on 512-, 1024- and 2048-point IRs: 1 and 2 and 3 and 4.

It's no use converting 1024-point IRs to 2048 since they don't contain the necessary data. You need a WAV-file to convert to 2048. A conversation utility is not yet available.

Where do I find 3rd-party IRs

3rd-party IRs are available from Ownhammer and [http:/www.RedWirez.com RedWirez] for Standard/Ultra as well as AFXII. Some of their IRS are included with the AFXII. You can load these IRs into the AFXII using the external cab slots.

Where is the Drive parameter in the cab block

This parameter has been removed from the Cab block in the AFXII. Instead, the Amp block has dynamic speaker modeling in the Amp block. Source

Does it have a cab type for acoustic guitar

No. There's a thread on the forum that contains Fishman Aurex IRs (1024-point). There's an IR available of an acoustic body that has been converted to 2048 points.

How do I manage the user cab slots

User cab slots is another name for external cab blocks, or impulse responses (IRs). (...)

Can I rename cabs in the user cab slots

Yes, using Axe-Edit. The AFXII uses the name contained in the sysex data of the IR-file to show on its display with a maximum of 32 characters. Source1 Source2

Can I make it sound like an amp in the room

Use the room simulation controls in the Cab block. These can be used with any IR. It's a special reverb algoritm.

Why are two cab blocks louder than a single one

Bakerman: "It depends on how you're panning. Assuming a mono signal sent to cabs: Stereo cab w/ Pan L and Pan R fully left & right will be the same output level as 2 mono cabs w/ balance L & R. If pans/balances are centered the 2 mono cabs will be 6 dB louder. Balance elsewhere would be between 0 and 6 dB louder, and balance doesn't correspond 1:1 to pan L/R for the same placement. Balances will need to be further toward -50 or 50. Source

OTHER EFFECTS

About CHORUS and QUAD-CHORUS

1. Blocks: 2.
2. Supports X/Y function.
3. Offers fixed types: digital mono, digital stereo, analog mono, analog stereo, japan ce-2, warm stereo, 80s style, triangle, 8-voice stereo.
4. The Chorus block of the AFXII models bucket-brigade delay lines (BBD). Source

About DELAY

1. Blocks: 2.
2. Supports the X/Y function.
3. The AFXII adds improvements to the Delay block: a two-band parametric EQ for the wet signal with low-cut and high-cut with adjustable slopes for the cut filters. The EQ stuff is on a separate GUI page with a graphical display. Source
4. Delay blocks now have a master feedback that goes to 200% for oscillating delay effects. Source
5. Offers fixed types: digital mono, digital stereo, analog mono, analog stereo, mono tape, stereo tape, ping-pong, dual, reverse, sweep, ducking, vintage digital, 2290 w/ mod, ambient stereo.
6. Reverse delay: (...).

About DETUNE

See Pitch.

About DRIVE

1. Blocks: 2. No hopes for more Drive blocks. Source
2. Supports the X/Y function.

About ENVELOPE FILTER

See (...).

About FEEDBACK SEND/RETURN

1. Blocks: 1. Source
2. This block can be used to route the signal. A common use is to extend the possible number of effects (have more than 12 blocks) by routing the signal from row to row.

About FLANGER

1. Blocks: 2.
2. Supports the X/Y function.
3. The Flanger block of the AFXII models bucket-brigade delay lines (BBD). Source
4. Offers fixed types: digital mono, digital stereo, analog mono, analog stereo, thru zero, stereo jet.

About GRAPHIC EQ

1. Blocks: ...
2. It's a 10-band EQ. Frequencies: 31, 63, 125, 250, 500, 1k, 2k, 4k, 8k, 16k. Source

About LOOPER

1. Blocks: 1. It's a dedicated block (instead of a Delay mode as on the Standard/Ultra).
2. The same features as on the Ultra (with stack and reverse) but with 60 seconds loop time. Source

About NOISE GATE

1. Blocks: (...).
2. There also is a global Noise Gate in the Layout menu. These separate Gate blocks are available for additional noise control.
3. You can use SCSEL (SideChain Select) to select the signal the gate is working with. If the gate is the first block in the routing there's no need to use SCSEL. But if the gate is placed after other blocks in the routing, it can be useful to use SCSEL to set an optimal source signal. Source

About PHASER

1. Blocks: 2.
2. Supports the X/Y function.
3. Offers fixed types: digital mono, digital stereo, script 45, script 90, block 90, classic vibe, stereo 8 stage - plus vibe mode.

About PITCH

1. Blocks: 2.
2. Supports the X/Y function.
3. The Pitch block has a Learn function. Turn it on, play a note, hold it. The AFXII now sets the key according to the note you played. Source1 Source2

About REVERB

1. Blocks: 2.
2. Supports the X/Y function. Source
3. The AFXII adds improvements to the Reverb block: there are improvements in the tail decay plus a two-band parametric EQ for the wet signal with low-cut and high-cut. The EQ stuff is on a separate GUI page with a graphical display. Source

About WAH

1. Blocks: 2.
2. Supports the X/Y function.
3. The Wah block of the AFXII models the Fasel Inductor. Source
4. Seek wah: (...).

CONTROLLERS, MODIFIERS

How many external controllers are supported

12.

How many steps does the Sequencer have

16.

Can a modifier be set to min and max values

In the AFXII there are MIN and MAX values. These are the actual parameter values. For example, if you want to change the delay time from 500 ms to 700 ms, you simply set MIN to 500 ms and MAX to 700 ms. So 0% corresponds to 500 ms and 100% corresponds to 700 ms. Source

PEDALS, SWITCHES, FOOT CONTROLLERS

Can the Quick Control knobs be used as pedals

Yes. Source

What's the purpose of the Rj45 port

Use this to connect the MFC-101, instead of using a MIDI cable. It uses a regular CAT-5 network cable and a propietary protocol. This supports bidirectional communication and phantom power. Source

When using the CAT-5 cable a 9V adapter is no longer needed to provide phantom power. Source1 Source2

When switching off the AFXII, the MFC-101 also switches off. Source

Does it support a future MFC-101 expansion unit

Yes. Source

How many pedals can be connected directly

One.

Is phantom power over 7-pin MIDI still supported

Yes. Pins 6 and 7 carry phantom power.

---

Index of How-Tos for Axe-Fx I, for editing purposes: FIRMWARE, SYSTEM'= How to save and restore stuff== How to replace the battery== SOFTWARE, AXE-EDIT= How to use it as an audio interface== How to use Axe-Edit== CREATING AND EDITING PRESETS= How to edit presets on a computer== How to use presets by other users== How to create a new preset from scratch== How to create your first preset== How to make editing easier== How to copy and paste effect settings between presets== How to reset an effect to its default state== How to adjust the global effects level or the master reverb level== How to insert more than 12 effects in a preset== How to add an effect to a preset== How to use effects in a parallel row== How to put effects before or after your own preamp== How to create a master bypass switch== How to run an effect in stereo or mono== How to set the correct bypass mode for an effect== How to set the volume level of an effect== How to adjust the volume level of a preset while playing== How to boost the signal for leads== How to avoid output clipping== How to decide where to put the cab block== How to enable spillover of delay trails and reverb== How to enable global control of any effects block== How to save and recall favorite amp settings (global amp)== How to minimize gaps in the signal when switching presets== How to print presets== How to keep your presets organized== How to insert an external pedal in the routing== EFFECTS'= How to know which effects are available== AMPS== How to know which amps are simulated=== How to dial in amp settings=== How to set the Drive and Master controls=== How to use the amp tone controls (tonestack)=== How to use the Bright switch=== How to use the Boost switch=== How to use the Presence control=== How to set the amp's advanced parameters=== How to split the preamp and poweramp of an amp sim=== How to get tight bass control=== How to use a Drive block to add or control gain=== How to add a gain stage=== How to prevent crossover distortion=== How to use multiple amps in a preset=== How to solve this issue: "My tone changes when I start editing the Amp block"=== How to get controlled feedback=== CABINETS== How to choose between the stock cabinets=== How to choose between the microphone sims=== How to choose between a stereo or mono cabinet=== How to use the Air and Drive parameters=== How to use an external user cab (IR)=== How to set the speaker resonance parameter=== How to optimize your room tone as well as the FOH tone === OTHER EFFECTS== How to create an automated dive bomb=== How to integrate a real talk box=== How to create the vibrato effect=== How to simulate a violin=== How to simulate multiple violins (strings)=== How to crossfade effects=== How to automate volume swells=== How to get or handle acoustic tones=== How to create U2’s Mysterious Ways effect=== How to create space(ship) and lasergun sounds=== How to simulate a flute=== How to simualte an organ=== How to get the shimmer effect=== How to simulate an E-Bow (infinite sustain)=== How to simulate the sound of a windstorm=== How to simulate a sitar or tampura=== How to create infinite reverb (freeze, hold reverb, chord-drone)=== How to simulate dropped tuning=== How to simulate sirens=== How to create automatic double-tracking (ADT)=== How to use Buzz Feiten tuning=== INTERNAL CONTROLLERS AND MODIFIERS== PEDALS, SWITCHES, FOOT CONTROLLERS, MIDI= How to get familiar with MIDI== How to configure the MIDI settings and stuff== How to handle MIDI problems== How to choose a MIDI foot controller== How to make your MIDI foot controller work== How to operate the MFC-101== How to power a MIDI foot controller through MIDI (phantom power)== How to access presets 128 and higher with a MIDI foot controller== How to switch effects on and off using a MIDI foot controller== How to activate the tuner using a MIDI foot controller== How to display the tuner on a MIDI foot controller's display== How to choose an expression pedal== How to connect and configure an expression pedal or switch== How to solve a "stuttering" expression pedal== How to turn an expression pedal into a wah== How to activate an effect automatically when moving an expression pedal== How to use a single pedal to control different effects without switching presets (dual-function pedal) == How to use a switch for global control of any effects block== How to reset a pedal when switching presets== How to mute the delay using an expression pedal or switch== How to switch between different effect settings using a single switch== How to use a pedal for volume boosts== RECORDINGS= VIDEOS'= CATEGORIZED FACTORY PRESETS=