Always consult the official Owners Manuals first!
March 2024: all pages have been checked and are up-to-date

Difference between revisions of "Volume/Panner block"

From Fractal Audio Wiki
Jump to navigation Jump to search
Line 27: Line 27:
 
Or simply copy the effect and Envelope settings from a factory preset that incorporates volume swells.
 
Or simply copy the effect and Envelope settings from a factory preset that incorporates volume swells.
  
Some Axe-Fx III effect types have a dedicated Envelope controller, allowing swells without the need to use the internal Envelope controller in the Controllers block.
+
Some Axe-Fx III effect types have a dedicated Envelope controller, allowing swells without the need to use the internal Envelope controller in the Controllers block. Owner's Manual:
 
 
Owner's Manual:
 
  
 
<blockquote>"For a basic volume “roll up” setting, try Threshold: -70.0 dB; Attack: About 400 ms; Release: about 15 ms. Increase Attack Time for a slower fade in."</blockquote>
 
<blockquote>"For a basic volume “roll up” setting, try Threshold: -70.0 dB; Attack: About 400 ms; Release: about 15 ms. Increase Attack Time for a slower fade in."</blockquote>

Revision as of 17:51, 17 July 2018

Available on which Fractal Audio products

  • Axe-Fx III: 4 blocks
  • Axe-Fx II: 4 blocks
  • AX8: 2 blocks
  • FX8: 2 blocks

X/Y and channels

  • Axe-Fx III: 4 channels
  • Axe-Fx II: no
  • AX8: no
  • FX8: no

Purposes

As a volume pedal

Assign an expression pedal to the Volume parameter in the Volume block to create a volume pedal.

For automated volume swells

Guitar players can fade in notes and chords by using their pink finger to operate the volume knob on their guitars. BOSS automated this method in their discontinued Slow Gear pedal.

To get a similar result, attach the Envelope internal controller to the Volume parameter in the Vol/Pan block, Input Gain in a Delay block or another effect block's Level or Input Gain parameter. Fine-tune the effect by adjusting the modifier settings, selecting the Taper in the Volume block and the Envelope settings. The Envelope's Attack parameter and the Volume block's Taper parameter determine the swell rate.

Or simply copy the effect and Envelope settings from a factory preset that incorporates volume swells.

Some Axe-Fx III effect types have a dedicated Envelope controller, allowing swells without the need to use the internal Envelope controller in the Controllers block. Owner's Manual:

"For a basic volume “roll up” setting, try Threshold: -70.0 dB; Attack: About 400 ms; Release: about 15 ms. Increase Attack Time for a slower fade in."

As a noise gate

Read this: Gate/Expander block.

To route signals

The Volume block doesn't require much CPU. This makes it a handy tool for routing. Set its Bypass parameter to Mute and put it at the start of a split signal to enable or disable a certain routing within a preset, depending on the bypass state of the Volume block. You can engage or bypass the block per scene.

As a lead boost

Place the Volume block at the end of the signal chain and increase its Level to turn it into a clean boost, through scenes or an assigned switch.

Parameters

Parameters table

Parameter Axe-Fx III Axe-Fx II AX8, FX8
Volume yes yes yes
Balance yes yes yes
Taper yes yes yes
Input Select yes yes yes
Pan Left/Right yes yes yes
Bypass Mode yes yes yes
Output Level yes yes yes

Taper

The Volume block offers various audio tapers.

"The number is the percentage at the halfway point. I.e. Log 20A means that the resistance is 20% at the halfway point in the travel. So if you put the knob at noon, the volume would be 20% of maximum (about -14 dB)." source

To simulate a Log taper in a Modifier menu, set "Mid" in the modifier menu to the log number, i.e. 20%. Adjust Slope to avoid the dead zone.

Input Select

Like the Amp and Drive blocks, the Input Select parameter in the Volume block determines whether the block processes only the left or right input signal, or both (stereo). It can send the processed signal to either side using Balance, or keep it stereo.