Always consult the official Owners Manuals first!
March 2024: all pages have been checked and are up-to-date

Difference between revisions of "Tempo"

From Fractal Audio Wiki
Jump to navigation Jump to search
Line 25: Line 25:
 
Audible bleed-through of the tempo signal can occur when the MIDI cable is not properly shielded.
 
Audible bleed-through of the tempo signal can occur when the MIDI cable is not properly shielded.
  
=Metronome=
+
=Tempo and MIDI=
The Axe-Fx II, AX8 and FX8 can emit a metronome signal. The metronome is located in the Tempo menu. You can start the metronome using a switch (assigned to the Metronome's MIDI CC) or through the Tempo menu. The metronome plays through Output 1 only.
+
==Auto-activate a Delay using Tap Tempo==
 
 
The Axe-FX III does not provide a metronome.
 
 
 
=Auto-activate a Delay using Tap Tempo=
 
 
If the parameter Auto Delay in the Tempo menu is “ON,” any delay blocks that are bypassed will become active whenever a tempo is tapped in. This allows you to set the tempo and un-bypass your delay block(s) from a single footswitch.
 
If the parameter Auto Delay in the Tempo menu is “ON,” any delay blocks that are bypassed will become active whenever a tempo is tapped in. This allows you to set the tempo and un-bypass your delay block(s) from a single footswitch.
  
=MIDI CCs for Tempo and Metronome=
+
==MIDI CCs for Tempo and Metronome==
 
* '''Tempo''': CC 14.
 
* '''Tempo''': CC 14.
 
* '''Metronome''': CC 122 (not on Axe-Fx III).
 
* '''Metronome''': CC 122 (not on Axe-Fx III).
  
=Showing tempo on on MIDI controllers=
+
==Showing tempo on a foot controllers==
 
Fractal Audio FC series indicate the preset tempo.  
 
Fractal Audio FC series indicate the preset tempo.  
  
3rd party controllers can also show tempo when they have been programmed to act as a client to the Axe-Fx III, using Fractal Audio's protocol. Regular MIDI does not suffice to accomplish. The Axe-Fx III does not provide a Send Realtime Sysex parameter anymore.
+
3rd party MIDI controllers can also show tempo when they have been programmed to act as a client to the Axe-Fx III, using Fractal Audio's protocol. Regular MIDI does not suffice to accomplish. The Axe-Fx III does not provide a Send Realtime Sysex parameter anymore.
  
=MIDI Clock=
+
==MIDI Clock==
 
The Axe-Fx II, Axe-Fx III, FX8 and AX8 do not transmit MIDI Clock to other devices. They can process an incoming MIDI clock signal.
 
The Axe-Fx II, Axe-Fx III, FX8 and AX8 do not transmit MIDI Clock to other devices. They can process an incoming MIDI clock signal.
 +
 +
=Metronome=
 +
The Axe-Fx II, AX8 and FX8 can emit a metronome signal. The metronome is located in the Tempo menu. You can start the metronome using a switch (assigned to the Metronome's MIDI CC) or through the Tempo menu. The metronome plays through Output 1 only.
 +
 +
The Axe-FX III does not provide a metronome.
  
 
[[category:Axe-Fx]]
 
[[category:Axe-Fx]]

Revision as of 14:18, 5 March 2018

The information on this page supplements the official manuals.

Metronome.png

Using Tempo in effect blocks

You can assign parameters such as Time or Rate to a specific tempo, like 1/4 or 1/8 Dotted, instead of number of milliseconds. That will make the effect depend on the global or preset tempo. Tapping a different tempo will change the rate of the effect.

Note: after assigning a parameter to a tempo, you can no longer adjust the time!

Tap Tempo modes in the Global menu

The Global menu lets you set the Tap Tempo operating mode:

  • Average: averages the tempo to the last ten taps.
  • Last Two: uses only the most recent two taps to determine the tempo.

Tempo menu

When tapping the Tempo button or switch, the Tempo menu appears. It will disappear after a few seconds. You can specify in the Global menu how long it should stay on-screen.

Tempo: global or preset

You can specify in the Tempo menu whether you want tempo to be set globally (across all presets) or per preset.

Tempo LED accuracy

"The tempo LED is handled by a low-priority thread so it isn't rock solid and the higher the CPU usage the less solid it will be." source

Ticking tempo noise

Audible bleed-through of the tempo signal can occur when the MIDI cable is not properly shielded.

Tempo and MIDI

Auto-activate a Delay using Tap Tempo

If the parameter Auto Delay in the Tempo menu is “ON,” any delay blocks that are bypassed will become active whenever a tempo is tapped in. This allows you to set the tempo and un-bypass your delay block(s) from a single footswitch.

MIDI CCs for Tempo and Metronome

  • Tempo: CC 14.
  • Metronome: CC 122 (not on Axe-Fx III).

Showing tempo on a foot controllers

Fractal Audio FC series indicate the preset tempo.

3rd party MIDI controllers can also show tempo when they have been programmed to act as a client to the Axe-Fx III, using Fractal Audio's protocol. Regular MIDI does not suffice to accomplish. The Axe-Fx III does not provide a Send Realtime Sysex parameter anymore.

MIDI Clock

The Axe-Fx II, Axe-Fx III, FX8 and AX8 do not transmit MIDI Clock to other devices. They can process an incoming MIDI clock signal.

Metronome

The Axe-Fx II, AX8 and FX8 can emit a metronome signal. The metronome is located in the Tempo menu. You can start the metronome using a switch (assigned to the Metronome's MIDI CC) or through the Tempo menu. The metronome plays through Output 1 only.

The Axe-FX III does not provide a metronome.