Scenes

Manual

16.16 Scenes — 4.3.1 Quick Control

User contributions

Preset scenes

• Each preset has 8 separate scenes. The routing (grid) in all scenes is always exactly identical. And the parameter values in all blocks also are always the same. The bypass state ("engaged/bypassed" aka "on/off") of each effect block can be different per scene. Also, the X/Y state of each effect block can vary per scene. Finally, each scene has its own output level setting (Gain in Layout menu), and this goes for the output level in the FXL block too. All in all, the scenes feature is comparable to an advanced switching system for a pedalboard or a 19" rack.
• Example: scene 1 of a certain preset may have everything on the grid bypassed except for the Amp/Cab blocks, both set to X. Scene 2 has 3 additional blocks engaged and the Amp block is set Y. With a simple stomp on the MIDI controller you can switch between scene 1 and 2.
• Mini Manual.

Preset scenes: advantages

• The routing stays the same, so there's no audio gap when switching between scenes within a preset. Note: switching an Amp between X/Y does cause a gap.
• Spillover of delay/reverb is unaffected when switching between scenes in a preset.
• You can migrate the functionality of various presets into a single preset and then use scenes to recall that functionality, or parts of it. This requires less presets and therefore decreases the need for bank scrolling on your MIDI controller.
• A change of the routing in a scene is inherited by the other scenes in the preset. This may decrease the need for global block functionality in certain scenarios.
• The output level is stored independently for each scene. This applies to the FXL block too. This presents a solution for those who use multiple guitars with different output levels with their Axe-Fx.
• You can use two Scene controllers to change parameters.

Preset scenes: scene indication

• Check the indicator on the front panel display or the Layout sreen.

Preset scenes: can scenes be named?

• No.

Preset scenes: switching scenes

• Front panel: use Quick Control knob A to select a scene within the current preset. You need to be in the Recall screen or Layout menu.
• MFC-101: the MFC-101 will let you assign switches to specific Scene functionality. You can assign a switch to each scene, or increment of decrement scenes, or toggle between scenes 1/2. The MFC-101 LEDs are refreshed after a scene change.
• MIDI controller:
  • Assign a switch to the MIDI CC for Scene Select (default 34) with values 0 to 7 to select scene 1 to 8 within the current preset. Values higher than 7 also select scene 8. Values higher than 63 will step through the scenes, wrapping at the limits. Also, there are dedicated MIDI CCs to increment or decrement the current scene. If you don't specify a value, the switch will switch between scene 1 and 8.
  • I/O > Mapping provides a Map To Scene parameter. This makes it possible to use a MIDI PC message to select a specific scene within a specific preset. After configuring the mapping, don't forget to set Mapping to Custom to activate it.
• Pedal jack:
  • Connect a momentary switch to the rear of the Axe-Fx.
  • In I/O > CTRL set Scene Increment to Pedal. In I/O > Pedal set Pedal Type to Latching.
• Notes:
  • When using the front panel to switch presets, scene 1 will always be active by default. Even if the preset was saved while being in scene other than the first.
  • The default MIDI CC for scene selection is 34. This CC previously was reserved for Global Bypass. The Global Bypass functionality has been removed due to the introduction of scenes.
  • To turn the bottom row of the MFC-101 into scenes switches, set the MFC's Bank Size to 0.

Preset scenes: initial block state

• Scenes 2 to 7 will have ALL effect blocks engaged initially. This is by design.

Preset scenes: can each scene have different X/Y block states?

• Yes. For example, the Delay 1 block in scene 1 can be set to X while the same Delay block in scene 2 is set to Y. This is extremely flexible. Note that using different types of Delay/Reverb in X and Y may impact spillover behavior. Of course, you also still use two instances of effect blocks (instead or in addition to X/Y states) in your presets. This lets you bypass/engage each instance per scene (at the expense of CPU usage).
• Notes:
  • Because of the implementation of X/Y in scenes, all blocks in pre-9.00 presets will be set to X initially.
  • Switching an Amp block between X/Y, in the same scene or between scenes, causes a short audio dropout.

Preset scenes: can each scene have different modifiers, different internal controller settings, different global blocks?

• The Scenes functionality was introduced to minimise audio gaps when switching between sets of tones. Therefore routings must be kept the same except for bypass states, X/Y and output volume. Modifier settings, controller settings and global blocks are the same in every scene.

Preset scenes: can I retain the current state of an effect when switching between scenes?

• For the same reason as explained above, you can't "dynamically" carry over the current state of an effect from the current scene to another one.
• If you want to retain effects block states in a switching scenario, stick to preset switching and use general use IA switches on your MFC-101, set to "global", or use external switches with your MFC-101.
• What you can do: tell the Axe-Fx how you want it to handle effect states when leaving and returning to a scene. By default the Axe-Fx remembers which block states you have bypassed/engaged after having selected a scene. If you then leave and return to that scene (without changing presets) the Axe-Fx will recall those changed states. If you prefer always recalling a scene in its saved state (block are set to the state they were in when saved), set the parameter “SCENE REVERT ON CC” in the I/O > MIDI menu to ON. Note that Revert doesn't apply to scene switching using Axe-Edit or the front panel. Also, Revert doesn't work with PC Mapping.

Preset scenes: Scene Controllers

• See Scene controllers.

Preset scenes: how to use them for more and faster control over the Axe-Fx

• Combine presets into a single preset for gapless switching.
• Use scenes instead of the MFC-101's Song Mode, to combine sounds for songs.
• Use two Amp blocks and if necessary two Cab blocks for more choice.
• Configure different X/Y states for effect blocks and vary these per scene.
• Decrease Bank Size on the MFC-101 to have more IA switches on your MFC-101 available for scene switching.
• Use the Alternate Preset functionality on the MFC-101 to get access to multiple presets (with scenes) through a single preset switch.
• Create an ad hoc "Lead" scene for each preset by adding a level boost (such as a NullFilter at the end of the grid), delay and drive block. Save a scene with these blocks engaged.
• Create a scene where only the Amp and Cab blocks in the routing are engaged and dedicate an IA switch to it. This switch lets you return to your basic tone at all times. Think of it as a "Panic" switch.
• When using various guitars, the use of scenes enables you to optimize the preset output level for each guitar. Also, you can bypass/engage stuff like a PEQ in each scene etc. for even more control.

Preset scenes: more information

• Wiki - PSI (Preset Scene Investigation)