Always consult the official Owners Manuals first
Difference between revisions of "Phaser block"
| Line 13: | Line 13: | ||
=Feedback Tap parameter in the Phaser block= | =Feedback Tap parameter in the Phaser block= | ||
| − | Fractal Audio: | + | Fractal Audio:<BR> |
"There is no feedback on a Script 90." [http://forum.fractalaudio.com/axe-fx-ii-bugs/52270-phaser-type-feedback-tap-incorrect-script-90-type.html#post669003 source] | "There is no feedback on a Script 90." [http://forum.fractalaudio.com/axe-fx-ii-bugs/52270-phaser-type-feedback-tap-incorrect-script-90-type.html#post669003 source] | ||
| Line 25: | Line 25: | ||
The Vibe effect is a special mode of the Phaser block. Set Vibe Mode to On (or select the Classic Vibe type). This mode at default settings was modeled after the Fulltone Deja-Vibe. [http://forum.fractalaudio.com/threads/need-help-with-some-sounds.109156/#post-1305852 source] | The Vibe effect is a special mode of the Phaser block. Set Vibe Mode to On (or select the Classic Vibe type). This mode at default settings was modeled after the Fulltone Deja-Vibe. [http://forum.fractalaudio.com/threads/need-help-with-some-sounds.109156/#post-1305852 source] | ||
| − | Fractal Audio: | + | Fractal Audio:<BR> |
"You need it before the amp if you want the bump." [http://forum.fractalaudio.com/axe-fx-ii-discussion/104710-recommendations-achieve-good-univibe-sound.html#post1252527 source] | "You need it before the amp if you want the bump." [http://forum.fractalaudio.com/axe-fx-ii-discussion/104710-recommendations-achieve-good-univibe-sound.html#post1252527 source] | ||
Revision as of 18:58, 9 April 2017
The information on this page supplements the official manuals.
Contents
- 1 Phaser: supported by which Fractal Audio products?
- 2 X/Y switching in the Phaser block
- 3 Phaser: mono or stereo output
- 4 Feedback Tap parameter in the Phaser block
- 5 Prevent thump when engaging the Phaser
- 6 Control the start of the Phaser sweep
- 7 Create an Uni-vibe effect
- 8 Barber Pole Phaser type
- 9 More information
Phaser: supported by which Fractal Audio products?
- Axe-Fx II: yes.
- AX8: yes.
- FX8: yes.
X/Y switching in the Phaser block
The Phaser block in the Axe-Fx II, AX8 and FX8 supports X/Y switching.
Phaser: mono or stereo output
Phaser defaults to mono to prevent phase problems when used before an Amp block. To make it stereo, change the LFO Phase setting and place it after Drive, Amp and (mono) Cab.
Feedback Tap parameter in the Phaser block
Fractal Audio:
"There is no feedback on a Script 90." source
Prevent thump when engaging the Phaser
If engaging/bypassing the Phaser block causes an audible thump or gap, change input impedance to 1M (Axe-Fx II and FX8).
Control the start of the Phaser sweep
Use the parameter “LFO Bypass Reset”. When set to anything other than “Off”, the LFO will be reset to the selected phase whenever the block is bypassed. This allows synchronizing the sweep to the engagement of the effect.
Create an Uni-vibe effect
The Vibe effect is a special mode of the Phaser block. Set Vibe Mode to On (or select the Classic Vibe type). This mode at default settings was modeled after the Fulltone Deja-Vibe. source
Fractal Audio:
"You need it before the amp if you want the bump." source
Tip: connect a pedal or switch (via an external controller) to the Rate parameter to control speed.
Barber Pole Phaser type
This phaser type works best when placed at the end of the chain.
