Always consult the official Owners Manuals first
Difference between revisions of "Firmware"
Jump to navigation
Jump to search
| Line 21: | Line 21: | ||
The firmware for the AX8 and FX8 includes a firmware update guide. | The firmware for the AX8 and FX8 includes a firmware update guide. | ||
| + | |||
| + | MFC-101: go to the [[MFC-101]] page. | ||
=Boot recovery= | =Boot recovery= | ||
| Line 40: | Line 42: | ||
* "The Axe-Fx II can be reprogrammed at least 100,000 times." [http://forum.fractalaudio.com/axe-fx-ii-discussion/53847-axe-fx-ii-firmware-version-6-02-up-8.html#post685291 source] | * "The Axe-Fx II can be reprogrammed at least 100,000 times." [http://forum.fractalaudio.com/axe-fx-ii-discussion/53847-axe-fx-ii-firmware-version-6-02-up-8.html#post685291 source] | ||
* "Most DSP compilers include library functions for common signal processing functions. However every library I've seen makes the same mistakes in several important and oft-used functions. I can't disclose what functions and what those mistakes are but because of this we use our own hand-coded assembly functions for our own libraries. The results are measurable and audible especially when dealing with the special requirements of amp modeling. I should add that these libraries are low-level functions like FFT() and such. You're not going to find a library that implements a Tube Screamer or even something more granular like a diode clipping circuit. That all has to be developed in-house." [http://www.thegearpage.net/board/index.php?threads/technical-question-about-modelers.1660147/#post-21221724 source] | * "Most DSP compilers include library functions for common signal processing functions. However every library I've seen makes the same mistakes in several important and oft-used functions. I can't disclose what functions and what those mistakes are but because of this we use our own hand-coded assembly functions for our own libraries. The results are measurable and audible especially when dealing with the special requirements of amp modeling. I should add that these libraries are low-level functions like FFT() and such. You're not going to find a library that implements a Tube Screamer or even something more granular like a diode clipping circuit. That all has to be developed in-house." [http://www.thegearpage.net/board/index.php?threads/technical-question-about-modelers.1660147/#post-21221724 source] | ||
| − | |||
| − | |||
| − | |||
[[Category:Axe-Fx]] | [[Category:Axe-Fx]] | ||
[[Category:FX8]] | [[Category:FX8]] | ||
[[Category:AX8]] | [[Category:AX8]] | ||
Revision as of 07:57, 10 April 2017
The information on this page supplements the official manuals.
Contents
Fractal Audio products firmware downloads
Firmware release notes
Update the firmware
Axe-Fx II: Firmware update guide for Axe-Fx II. Including troubleshooting tips.
Always disconnect the MFC-101 when updating the firmware on the Axe-Fx II.
The firmware for the AX8 and FX8 includes a firmware update guide.
MFC-101: go to the MFC-101 page.
Boot recovery
Built-in backup firmware in the Axe-Fx II XL and XL+, FX8 and AX8 allows recovery in the event of complications during update.
- Axe-Fx II XL/XL+: hold down Page Left and Page Right while cycling power.
- FX8: hold down SETUP and power the unit on. Hold the button for about 1 second beyond the power up, then release. The unit will now allow you to install firmware using Fractal-Bot.
- AX8: hold down SHIFT and power the unit on. Hold the button for about 1 second beyond the power up, then release. The unit will now allow you to install firmware using Fractal-Bot.
If the Axe-Fx II or AX8 sounds bad after an update, try reinstalling the firmware, or perform a system reset.
Updating presets after a firmware update
Updated firmware may cause changes in your presets. Read the firmware release notes and verify your presets.
Firmware: more information
The Axe-Fx firmware is coded in C and assembly. source
Fractal Audio:
- "The Axe-Fx II can be reprogrammed at least 100,000 times." source
- "Most DSP compilers include library functions for common signal processing functions. However every library I've seen makes the same mistakes in several important and oft-used functions. I can't disclose what functions and what those mistakes are but because of this we use our own hand-coded assembly functions for our own libraries. The results are measurable and audible especially when dealing with the special requirements of amp modeling. I should add that these libraries are low-level functions like FFT() and such. You're not going to find a library that implements a Tube Screamer or even something more granular like a diode clipping circuit. That all has to be developed in-house." source
