Compressor block

The information on this page supplements the official manuals.

Image to be added

Compressor/Dynamics: supported by which Fractal Audio products

• Axe-Fx III: 2x.
• Axe-Fx II: 2x.
• FX8: 2x.
• AX8: 1x.

Compressor/Dynamics: X/Y switching or channels

• Axe-Fx III: 4 channels.
• Axe-Fx II: yes.
• FX8: yes.
• AX8: yes.

There's no MIDI CC available for X/Y switching in the Axe-Fx II XL/XL+.

About the compressor types

• Pedal 1 and 2: "Pedal 2" uses a different algorithm which is smoother and pumps less than "Pedal 1". CPU usage by both types is much less than the "Studio" type.
• Dynamics: this algorithm allows compression or expansion with a single control. When set to negative values, the block compresses the signal. When set to positive values, the block expands the signal.
• Optical 1 and 2: Optical 1 is based on classic optical tube compressors famed for their smooth sound. Use it before the Amp block to smooth out your licks and increase sustain, use it after the Amp block for instant “Hit Record” sound. Optical 2 is similar to Optical 1 but uses a true RMS detector.

"Optical 1 uses a full-wave rectifier as a detector (peak detector). Optical 2 uses a true RMS detector. The LA-2A and many other compressors use rectifiers as detectors because it's easy and simple. Technically true-RMS detectors are "better" but they are difficult to implement in analog hardware. Whether or not true-RMS is better in actual real-world applications is debatable. There are those that claim that true-RMS detectors more closely replicate the natural compression behavior of the human auditory system. Peak detectors respond more rapidly to transients while RMS detectors have a smoother behavior. The only way to know which you like better is to try them." source

"It's not an "LA-2A" but it can sound like one. It's a generic optical compressor that can be adjusted to sound like a variety of compressors. It has adjustable attack, release and compression." source

"The LA-2A, CL1B, et. al. are high-end studio compressors that use optical circuits." source

Compressor/Dynamics in the Axe-Fx III

• The old RMS detector has been removed. Now "RMS"is the same as "Fast RMS" in the AX8 and Axe-Fx II.
• An "E-L Panel" mode has been added to the optical compressor.
• Input Level has been removed from the Pedal types.
• The Studio Compressor has been changed; the threshold has been calibrated and its range has been adjusted.

Compressor block vs compression in the Amp block

The Amp block has built-in compression: a Dynamics parameter in the preamp section (same as the compressor's Dynamics mode), and OUT COMP at the output. You can use it instead of a separate Compressor block. It increases CPU usage.

"The Dynamics knob in the Amp block does the same thing as the Dynamics mode of the compressors so you can save a block that way." source

Position of the Compressor/Dynamics block

Placing the Compressor block after the Amp block makes it interfere less with the amp dynamics.

When placing a Pedal or Optical type compressor after the Amp block, set its input to Line (instead of Instrument).

Compressor/Dynamics parameters

Mix

Compressors are used mostly as a 100% wet effect. But there are compressors with Blend or Mix controls. These can be simulated by using the Mix parameter.

Sidechain Select

You can use the signal that enters the grid to feed the compressor, even if the compressor block is placed further upon the grid, through the Sidechain Select parameter (Studio mode only).

Release (Pedal mode)

"Pedal compressors typically have very long release times so the time is scaled by 10 for pedal mode. The time in studio mode is accurate to within a microsecond." source

"The times are the classic "time constants" for analog circuits, i.e. the time it takes for a signal to settle to 37% of it's final value (e^-1)." source

Emphasis

This boosts the high frequencies prior to compression and then lower them after.

Filter

Filter is a low-cut filter which can be used to tailor the response of the various compressor types to different material.

In the Axe-Fx III the Filter parameter has been replaced with EQ-ing tools.

Lookahead

The default Lookahead value has been changed to 0 in firmware 16.x and later, because of detector improvements.

Fast RMS detector

The “Fast RMS” Detector type in the Studio Comp mimics the fast detectors in classic rack-mount compressors. It uses less CPU than the other detectors.

Use the compressor as a limiter

There's no dedicated brickwall limiter in the unit, but the compressor can be used as such. From the manual: "Setting the RATIO to “INFINITY” turns the compressor into a “limiter,” reducing any level above the threshold to the threshold, applying a sort of “ceiling” or “brick-wall limiting” above which nothing can rise." More information.

More information about compressors

• Radley's extensive and comprehensible Compression tips.
• Compressor FAQ.
• Danny Danzi's video tutorial.
• Dynamic range compression in Wikipedia.
• Compressors settings for country.
• Emulate the Solo Dallas Schaffer, more information.
• Pete Thorn explains compressor controls.