Always consult the official Owners Manuals first!
March 2024: all pages have been checked and are up-to-date

Channels

From Fractal Audio Wiki
Jump to navigation Jump to search

Iii all-blocks-3x13.jpg

Available on which products

  • Axe-Fx III and FM3: yes
  • Axe-Fx II: no
  • MFC-101: no
  • AX8: no
  • FX8: no

What are channels

About presets, scenes and channels:

  • Preset: like your traditional pedalboard.
  • Scene: like your traditional pedalboard at a particular moment, with effects being on or off, and set to a channel.
  • Channel: like one of the pedals on that pedalboard with its controls set in a specific way. There are 4 channels so 4 different sets of settings.

Most of the effect blocks in firmware Ares and later have multiple channels. Channels can be regarded as mini-presets in each block. Each channel provides a unique set of parameter values. Switching between channels is instantaneous and pretty seamless and can be done manually (on the hardware or with a foot controller) or automatically when changing scenes. Channels can also be switched via MIDI for applications requiring automation.

Channels provide quick and easy switching between sounds without the unwanted side-effects of preset changes (due to grid reordering). For example, set the Amp block so that Channel A is a “Deluxe Verb” model, Channel B is a “Plexi”, Channel C is a “Recto” and Channel D is “FAS Modern”. Then change channels almost instantly at the touch of a button.

Channel-switching is the successor of X/Y switching, a feature of the Axe-Fx II, AX8, FX8 (and MFC-101).

More explanation in the Owner's Manual

"Channels are the cat's sphincter. Many blocks, including the amp block, have four channels. Channels switch instantly." source

"Channels save all settings for a block. A channel is like a preset within a block." source

"Channels can be thought of as a preset for an individual block. For example, you can think of the Delay block as being a stand-alone delay pedal (or rackmount processor) with four presets. Scenes store the bypass state and channel for each block. By using scenes and channels you can use a single preset for an entire song, an entire set or even the entire show. Since the routing doesn't need to change things switch fast and smooth. When switching presets the processor has to assume the routing might have changed and therefore has to clear all the buffers, mute the audio, etc. which takes time and interrupts the audio." source

The Axe-Fx III was designed so that single preset can be thought of as an entire rack full of processors. Each virtual processor has up to four presets. So if you were trying to do spillover in a rack you would use two reverb processors. source

"The Control block has four channels." source

Which effect blocks have channels

The list below applies to the Axe-Fx III.

The effect blocks on the FM3 have the same number of channels as on the Axe-Fx III.

Note: the Multiplexer actually has 6 channels.

Iii-effect-types-table-364x1024.gif

And read this:

How to switch between channels

To switch between the channels of an effect block, use:

  • the hardware GUI
  • the software editor
  • presets
  • scenes
  • FC-6 or FC-12 controller
  • MIDI: assign a MIDI CC in Setup > MIDI/Remote > Channel (Axe-Fx III and FM3 only, and specify a value to select a specific channel:
0 = A
1 = B
2 = C
3 = D

Switching channels can cause an audio gap

When switching channels on an Amp block, there will be a short gap in the sound. Channels do NOT run simultaneously. They do not crossfade. If you need crossfading, use the Mixer block which can crossfade between input sources, or use a Scene Controller.

"Crossfading channels would require that two instances of an effect be running at all times. This would cut the useable CPU in half. Most people wouldn't like that. source

Also read this:

Channels and CPU usage

CPU usage is calculated based on the currently selected channel of an effect. When switching channels, CPU usage may change.

Channels and modifiers

If a controller is assigned as a source to a parameter in a modifier menu, you can choose between applying it to all channels of that block, or to just a single channel.

Note: a parameter allows only one modifier, not multiple.

Read this: Modifiers, Controllers and Control Switches

Managing channels

On the hardware, channel settings can be copied-and-pasted within the same block (Layout > Tools), or swapped.

To copy channels between blocks and to/from other presets, use the software editor.

Resetting a channel or an entire block

Resetting a block defaults the parameters of the current channel. It does not change the settings of other channels.

To reset all channels of the block, switch to the other channels and repeat the process, or use the software editor to reset the entire block in one go.

Read this: Resetting blocks

Using channels to compare sounds and parameters

Channels offer an easy way to compare sounds when tweaking. They also allow you to quickly detect non-default settings by resetting one channel to default settings and then comparing the channels.

An alternative approach to comparing sounds is saving a preset as a Snapshot in the editor. Select Revert to get the original sound back. Then drag and drop the Snapshot file into the editor.