Always consult the official Owners Manuals and Guides first.
Information about the FM3 may be incomplete or wrong, it's being worked on.

Difference between revisions of "Amp and Cab modeling for beginners"

From Fractal Audio Wiki
Jump to: navigation, search
Line 24: Line 24:
  
 
'''Questions,troubles?'''<BR>
 
'''Questions,troubles?'''<BR>
Consult the [http://www.fractalaudio.com/downloads/manuals/axe-fx-2/Axe-Fx-II-Owners-Manual.pdf Owner's Manual], check this wiki, read the [http://forum.fractalaudio.com/axe-fx-ii-discussion/74884-troubleshooting-faq.html#post915618 Troubleshooting FAQ] and [http://forum.fractalaudio.com/search.php?searchid=3742292 visit the forum].
+
Consult the [http://www.fractalaudio.com/downloads/manuals/axe-fx-2/Axe-Fx-II-Owners-Manual.pdf Owner's Manual], delve into this wiki, read the [http://forum.fractalaudio.com/axe-fx-ii-discussion/74884-troubleshooting-faq.html#post915618 Troubleshooting FAQ] and [http://forum.fractalaudio.com/search.php?searchid=3742292 visit the forum].
  
 
Have fun!
 
Have fun!
  
 
[[category:About the Axe-Fx II]]
 
[[category:About the Axe-Fx II]]

Revision as of 17:05, 1 April 2014

Virtual preamp
The Axe-Fx is a guitar preamp. It models more than hundred real amps such as heads, combos and racked preamps. You can also use its many other effects, use it to reamp a dry signal, create tone matches, use it for mastering, etc.

Virtual power amp
It has built-in power amp simulation, which means that you can listen to the sounds of the modeled amps through headphones, and connect the Axe-Fx to a mixer or record it without needing a separate power amp.

Using a real power amp
To amplify the Axe-Fx through a real speaker, you need an physical power amp. This can be a standalone tube power amp designed for guitar, a head or combo (through its effects loop), or a so-called neutral power amp.
You can also use studio monitors and monitor wedges with built-in amplifiers ("active", "powered").
Depending on the amplification device you engage or disable the Axe-Fx's power amp simulation.

Playing through a guitar speaker
The speaker you use is very important for the tone.
You can use the Axe-Fx with a traditional guitar speaker, in combination with a power amp. This will give you the familiar "amp-in-the-room" tone. It does limit the possibilities of the Axe-Fx, because any sound you will create will go through that speaker en therefore will be colored by it.

Playing through FRFR amplification
You can opt for FRFR (full-range flat response) sound reproduction. This requires a FRFR speaker and an external or built-in neutral (power) amp. Studio monitors are FRFR, as well as some wedges / cabs.
A FRFR setup requires power amp simulation and cabinet simulation to be engaged. Cabinet simulation means that the sound of a virtual speaker cabinet is added to the tone of the modeled amp. The Axe-Fx comes with many built-in cabinet models and allows loading external cab models, known as IRs or user cabs (Impulse Responses).

Listening to FRFR amplification
It's very important to realize that when you're using FRFR with cabinet simulation, you'll be listening to the sound of a mic'd speaker, as opposed to an amp-in-the-room. A cab model always represents the tone of a speaker that as captured using one or more microphones, mostly positioned very close to the speaker. That's totally different from listening to a guitar speaker at some distance. FRFR has more lows, more highs and has the coloring of the used microphone baked in. It takes a while to get accustomed to FRFR tone, but it's the tone the audience hears too through the FOH system and when listening to recorded music.

About clipping
Be aware that input clipping is something totally different than output clipping.
It's okay for the input LED to "tickle" the red. If it happens all the time, decrease Input Level the I/O menu. Be aware in this is not a real input level control, the control controls the signal-to-noise ratio only and does NOT affect signal level or gain.
The output clipping LED light indicates that the signal level in the effects chain is too hot. Adjusting Input Level does NOT solve this. Decrease the level somewhere in the chain.

Software
Axe-Edit — load and save presets from/to disk, edit sounds, rearrange presets and user cabs.
Fractal-Bot — backup or restore your Axe-Fx, load/save presets and user cabs, upgrade the firmware.
Cab-Lab — mix IRs and send them to the Axe-Fx, convert IRs, create an IR of your guitar cabinet (IR Capture).

Questions,troubles?
Consult the Owner's Manual, delve into this wiki, read the Troubleshooting FAQ and visit the forum.

Have fun!