Always consult the official Owners Manuals and Guides first.
Information about the FM3 may be incomplete or wrong, it's being worked on.

Difference between revisions of "Amp and Cab modeling for beginners"

From Fractal Audio Wiki
Jump to: navigation, search
Line 12: Line 12:
  
 
'''FRFR amplification'''<BR>
 
'''FRFR amplification'''<BR>
You can opt for FRFR (full-range flat respons) sound reproduction. This requires a FRFR speaker and an external or built-in neutral (power) amp. Studio monitors are FRFR, as well as some wedges / cabs.<BR>A FRFR setup requires power amp simulation and cabinet simulation to be engaged. Cabinet simulation means that the sound of a virtual speaker cabinet is added to the tone of the modeled amp. The Axe-Fx comes with many built-in cabinet models and allows loading external cab models, known as IRs (Impulse Responses).
+
You can opt for FRFR (full-range flat respons) sound reproduction. This requires a FRFR speaker and an external or built-in neutral (power) amp. Studio monitors are FRFR, as well as some wedges / cabs.<BR>A FRFR setup requires power amp simulation and cabinet simulation to be engaged. Cabinet simulation means that the sound of a virtual speaker cabinet is added to the tone of the modeled amp. The Axe-Fx comes with many built-in cabinet models and allows loading external cab models, known as IRs or user cabs (Impulse Responses).
  
 
'''FRFR amplification: tone'''<BR>
 
'''FRFR amplification: tone'''<BR>
 
It's very important to realize that when you're using FRFR with cabinet simulation, you'll be listening to the sound of a mic'd speaker, as opposed to an amp-in-the-room. A modeled cab always represents the tone of a speaker that as captured using a microphone, mostly very close to the speaker. That's different from listening to a guitar speaker at some distance. FRFR has more lows, more highs and has the coloring of the used microphone baked in. It takes a while to get accustomed to FRFR tone, but it's the tone the audience hears too through the FOH system and when listening to recorded music.
 
It's very important to realize that when you're using FRFR with cabinet simulation, you'll be listening to the sound of a mic'd speaker, as opposed to an amp-in-the-room. A modeled cab always represents the tone of a speaker that as captured using a microphone, mostly very close to the speaker. That's different from listening to a guitar speaker at some distance. FRFR has more lows, more highs and has the coloring of the used microphone baked in. It takes a while to get accustomed to FRFR tone, but it's the tone the audience hears too through the FOH system and when listening to recorded music.
  
 +
'''About clipping'''<BR>
 +
Be aware that input clipping is something totally different than output clipping.<BR> There's no real input level control on the Axe-Fx. That control (in the I/O menu) controls the signal-to-noise ratio only and does not affect level or gain.<BR>Output clipping means that the signal level in the chain is too high. Adjusting Input Level won't solve this. Decreasing Decrease the level somewhere (the Level parameter in the Amp block is a good place).
 +
 +
'''Software'''<BR>
 +
Use Axe-Edit to load and save presets from/to disk, edit presets, rearrange presets and user cabs etc.<BR>Use Fractal-Bot to backup or restore your Axe-Fx, load/save presets and user cabs, upgrade the firmware.<BR>Use Cab-Lab to load user cabs and mix multiple IRs.
 +
 +
For more information, delve into the wiki.
 
Have fun!
 
Have fun!
  
 
[[category:About the Axe-Fx II]]
 
[[category:About the Axe-Fx II]]

Revision as of 16:32, 1 April 2014

Virtual preamp
The Axe-Fx is a guitar preamp. It models more than hundred real amps such as heads, combos and racked preamps. You can also use the Axe-Fx for effects only, for mastering etc.

Virtual power amp
It has built-in power amp simulation, which means that you can listen to the sounds of the modeled amps through headphones, and connect the Axe-Fx to a mixer or record it without needing a separate power amp.

Real power amp
To amplify the Axe-Fx through a real speaker, you need an physical power amp. This can be a standalone tube power amp designed for guitar, a head or combo (through its effects loop), or a so-called neutral power amp.
You can also use studio monitors and monitor wedges with built-in amplifiers ("active", "powered").
Depending on the amplification device you engage or disable the Axe-Fx's power amp simulation.

Guitar speaker
The speaker you use is very important for the tone.
You can use the Axe-Fx with a traditional guitar speaker, in combination with a power amp. This will give you the familiar "amp-in-the-room" tone. It does limit the possibilities of the Axe-Fx, because any sound you will create will go through that speaker en therefore will be colored by it.

FRFR amplification
You can opt for FRFR (full-range flat respons) sound reproduction. This requires a FRFR speaker and an external or built-in neutral (power) amp. Studio monitors are FRFR, as well as some wedges / cabs.
A FRFR setup requires power amp simulation and cabinet simulation to be engaged. Cabinet simulation means that the sound of a virtual speaker cabinet is added to the tone of the modeled amp. The Axe-Fx comes with many built-in cabinet models and allows loading external cab models, known as IRs or user cabs (Impulse Responses).

FRFR amplification: tone
It's very important to realize that when you're using FRFR with cabinet simulation, you'll be listening to the sound of a mic'd speaker, as opposed to an amp-in-the-room. A modeled cab always represents the tone of a speaker that as captured using a microphone, mostly very close to the speaker. That's different from listening to a guitar speaker at some distance. FRFR has more lows, more highs and has the coloring of the used microphone baked in. It takes a while to get accustomed to FRFR tone, but it's the tone the audience hears too through the FOH system and when listening to recorded music.

About clipping
Be aware that input clipping is something totally different than output clipping.
There's no real input level control on the Axe-Fx. That control (in the I/O menu) controls the signal-to-noise ratio only and does not affect level or gain.
Output clipping means that the signal level in the chain is too high. Adjusting Input Level won't solve this. Decreasing Decrease the level somewhere (the Level parameter in the Amp block is a good place).

Software
Use Axe-Edit to load and save presets from/to disk, edit presets, rearrange presets and user cabs etc.
Use Fractal-Bot to backup or restore your Axe-Fx, load/save presets and user cabs, upgrade the firmware.
Use Cab-Lab to load user cabs and mix multiple IRs.

For more information, delve into the wiki. Have fun!