October 2024: Fractal Audio's VP4 Virtual Pedalboard has been added to the wiki.
X/Y switching (legacy)
The information on this page supplements the official manuals.
Contents
- 1 X/Y switching: supported by which Fractal Audio products?
- 2 About X/Y switching
- 3 Blocks with X/Y support
- 4 X/Y switching and scenes
- 5 X/Y switching on the hardware
- 6 X/Y switching in the software editors
- 7 X/Y indication
- 8 X/Y switching and CPU usage
- 9 Copying and swapping X/Y settings
- 10 Resetting effect parameters and X/Y settings
- 11 Modified parameters and X/Y settings
- 12 Recall Effect and X/Y settings
- 13 Using X/Y switching to compare sounds and settings
- 14 X/Y switching on the MFC-101 and other MIDI controllers
X/Y switching: supported by which Fractal Audio products?
- Axe-Fx II: yes.
- MFC-101: yes.
- AX8: yes.
- FX8: yes.
About X/Y switching
Fractal Audio: "The idea behind X/Y is that people often have multiple distortion/chorus/delay/etc. pedals on their board but they rarely have more than one on at a time. So rather than creating more instances of effects, which sucks up CPU, have each instance capable of more than one sound."
X/Y-switching occurs at block level, not at preset level.
There's no crossfading when switching between X and Y. If you want crossfading, use Scene Controllers as an alternative to X/Y switching.
Blocks with X/Y support
- Axe-Fx II Mark I and II: Amp, Cab, Chorus, Delay, Drive, Flanger, Phaser, Pitch, Reverb, Wah, Rotary.
- Axe-Fx II XL and XL+: Amp, Cab, Chorus, Compressor/Dynamics, Delay, Drive, Flanger, GEQ, Gate, Mixer, PEQ, Phaser, Pitch, Rotary, Reverb, Tremolo, Wah.
- AX8: Amp, Cab, Chorus, Compressor/Dynamics, Delay, Drive, Filter, Flanger, Gate, Multi Delay, Phaser, Pitch, Rotary, Reverb, Tremolo, Wah.
- FX8: Chorus, Compressor/Dynamics, Delay, Drive, Filter, Flanger, Gate, MIDI, Multi Delay, Phaser, Pitch, Relay, Rotary, Reverb, Tremolo, Wah.
Fractal Audio: "Any blocks that have X/Y on the XL but not on the Mark II will not import the bypass state as that is stored differently. You need to manually adjust the bypass state after import." source
X/Y switching and scenes
The X/Y state of an effect can vary per Scene. This is one of the advantages of using scenes.
X/Y switching on the hardware
Axe-Fx II: use the dedicated X/Y buttons on the front panel.
FX8 and AX8:
- Hold a switch (1-8) to alternate between X and Y. If the LED is amber lit, Y is active.
- You can also assign one of the 3 switches at the right to "Single X/Y" or "Sticky X/Y".
- You can adjust the switch "hold" time in the Global menu.
- You can also switch an effect between X and Y on the grid, using a shortcut key:
- AX8: SHIFT + 2x EDIT on LAYOUT page, or 2x EDIT in a block's editing mode.
- FX8: 2x EDIT on CFG screen.
X/Y switching in the software editors
Press the "X" key on the keyboard to switch a block between X and Y in the software editor.
The X/Y-states of the blocks are displayed in the software editor, without needing to select the block first.
X/Y indication
The X/Y state of effects blocks is shown in the software editors.
On the AX8 hardware the current X/Y state of the selected block is shown at the bottom of the Layout page.
On the Axe-Fx II and FX8 hardware the current X/Y state of the selected block is shown in an effect block's EDIT menu (not on the Layout page).
X/Y switching and CPU usage
CPU usage is calculated using the current state of a block (X or Y). When switching an effect between X and Y, CPU usage may change.
Copying and swapping X/Y settings
X and Y effect settings can be copied using the front panel of the Axe-Fx II: press X or Y twice quickly.
Swapping X and Y always requires use of a software editor.
Resetting effect parameters and X/Y settings
Resetting an effect block on the hardware resets the parameters to their default values. This only applies to the current state: X or Y. To reset the entire block, switch to the other state and repeat the process (or use the software editor to initialize the entire block).
Modified parameters and X/Y settings
- When a controller is assigned to a parameter, it always applies to both X and Y. It's not possible to have different modifier settings for X and Y, the architecture doesn't allow for this. source
Recall Effect and X/Y settings
Using Recall Effect on the Axe-Fx II and AX8 will always import all effect block settings: X and Y. So you can't use Recall Effect for just X or just Y. Use the software editor instead to copy and paste X-only or Y-only settings.
Using X/Y switching to compare sounds and settings
X/Y switching offers an easy way to compare sounds when tweaking. Example:
- Go to an AMP block, state "X".
- Double-click "Y" on the front panel to copy the "X" settings into "Y".
- Select X or Y and adjust settings.
- Now alternate between X and Y to see and hear the differences.
You can also do this in the software editor.
This also offers an easy method to quickly see where effect settings differ from default, by resetting X or Y to default.
An alternative approach to comparing sounds on the Axe-Fx II: save a preset as a Snapshot in the editor. Select Revert to get the original sound back. Then drag and drop the snapshot file into the editor.
X/Y switching on the MFC-101 and other MIDI controllers
There's a dedicated MIDI CC for most blocks that offer X/Y switching. Assign this CC to a switch to alternate between X and Y.
You can configure X/Y effect blocks to engage the effect in either X or Y mode. Example: (source)
- IA Switch 1, ON message: DELAY 1 ON, DELAY 1 X (CC#47:127, CC#106: 127)
- IA Switch 1, OFF message: DELAY 1 OFF, DELAY 1 X (CC#47:0, CC#106: 127)
- IA Switch 2, OFF message: DELAY 1 ON, DELAY 1 Y (CC#47:127, CC#106: 0)
- IA Switch 2, OFF message: DELAY 1 OFF, DELAY 1 Y (CC#47:0, CC#106: 0)
Or use a controller's "group" or'"linked switches" feature.
On the MFC-101 X is green, Y is red. If you prefer the default state to be green, use Y as the default state.