October 2024: Fractal Audio's VP4 Virtual Pedalboard has been added to the wiki.
Difference between revisions of "Realtime Analyzer block"
| Line 6: | Line 6: | ||
* '''Axe-Fx III''': 1 block | * '''Axe-Fx III''': 1 block | ||
| − | * '''FM3''': | + | * '''FM3''': yes |
* '''Axe-Fx II''': no | * '''Axe-Fx II''': no | ||
* '''AX8''': no | * '''AX8''': no | ||
| Line 13: | Line 13: | ||
=X/Y and channels= | =X/Y and channels= | ||
* '''Axe-Fx III''': no | * '''Axe-Fx III''': no | ||
| − | * '''FM3''': | + | * '''FM3''': no |
* '''Axe-Fx II''': n/a | * '''Axe-Fx II''': n/a | ||
* '''AX8''': n/a | * '''AX8''': n/a | ||
| Line 85: | Line 85: | ||
[[category:Axe-Fx3]] | [[category:Axe-Fx3]] | ||
| + | [[category:FM3]] | ||
[[category:Sounds]] | [[category:Sounds]] | ||
Revision as of 10:32, 29 April 2019
Contents
Available on which Fractal Audio products
- Axe-Fx III: 1 block
- FM3: yes
- Axe-Fx II: no
- AX8: no
- FX8: no
X/Y and channels
- Axe-Fx III: no
- FM3: no
- Axe-Fx II: n/a
- AX8: n/a
- FX8: n/a
About the RTA
The RTS provides detailed visual feedback of the audio spectrum. Possible uses are described below.
Many users will just use it because it looks pretty and dynamic.
It can point out frequencies where undesired feedback occurs. You can then use a PEQ to cut those frequencies.
“Use it to identify problem frequencies or as a spiffy screen saver.” source
It can used to test hardware I/O. For example, to test the Instrument input: (source)
- Go to a blank preset.
- Create a chain that connects Input 1 to the RTA block. On a separate row create a chain where the Synth block feeds Output 3.
- Set the Synth Type = Sine, Tracking = Off, Frequency = 1000 Hz.
- Connect an instrument cable from Output 3 (left or right) to the Instrument Input.
- Set the Input 1 / Instrument A/D Input Level (Home->Setup->I/O) to 50%.
- Turn the Out 3 Level knob all the way up.
- The Input 1 yellow LED should be lit. Red should not be lit. Go to the RTA block Config tab. Set Bands to 128, Window to Blackman. Go to the RTA tab. There should be a narrow spike at 1 kHz (three bands). There should be no other bands showing power except maybe a little noise at the highest bands. The spike at 1 kHz should be about 2 1/4 divisions below full-scale.
And it can be used to measure the output of other equipment, in conjunction with the Synth block. For example, to measure the frequency response of an external EQ or distortion pedal, set the Synth block to Pink Noise, send the Synth's signal through the pedal and back again, and use the RTA to measure and see the response.
Connecting the RTA
The RTA block requires an input signal and doesn't send a signal out, so its output doesn't need to be connected.
How to view the RTA
Scroll to the RTA block and press Edit to view the dynamic meters. It makes for a great display during performances.
To make the peaks remain longer visible, adjust Decay Time.
Turn the Value knob to select the desired band, and the frequency of the selected band will be displayed in the upper left corner.
Parameters table
| Parameter | Axe-Fx III | Axe-Fx II | AX8, FX8 |
|---|---|---|---|
| Decay Time | yes | n/a | n/a |
| Input Select | yes | n/a | n/a |
| Bands | yes | n/a | n/a |
| Window Type | yes | n/a | n/a |
