October 2024: Fractal Audio's VP4 Virtual Pedalboard has been added to the wiki.
Difference between revisions of "Tempo"
| Line 18: | Line 18: | ||
=Tempo LED accuracy= | =Tempo LED accuracy= | ||
| − | <blockquote>"The tempo LED is handled by a low-priority thread so it isn't rock solid and the higher the CPU usage the less solid it will be | + | <blockquote>"The tempo LED is handled by a low-priority thread so it isn't rock solid and the higher the CPU usage the less solid it will be." [http://forum.fractalaudio.com/axe-fx-ii-discussion/51049-does-tempo-led-actually-flash-time.html#post658471 source] </blockquote> |
=Tempo is part of MIDI data= | =Tempo is part of MIDI data= | ||
| Line 27: | Line 27: | ||
=Metronome= | =Metronome= | ||
| − | + | The Axe-Fx II, AX8 and FX8 can emit a metronome signal. The metronome is located in the Tempo menu. You can start the metronome using a switch (assigned to the Metronome's MIDI CC) or through the Tempo menu. The metronome plays through Output 1 only. | |
| − | The metronome | + | The Axe-FX III does not provide a metronome. |
=Auto-activate a Delay using Tap Tempo= | =Auto-activate a Delay using Tap Tempo= | ||
| Line 36: | Line 36: | ||
=MIDI CCs for Tempo and Metronome= | =MIDI CCs for Tempo and Metronome= | ||
* Tempo: CC 14 | * Tempo: CC 14 | ||
| − | * Metronome: CC 122 | + | * Metronome: CC 122 (not on Axe-Fx III) |
=Using Tempo in effect blocks= | =Using Tempo in effect blocks= | ||
Revision as of 21:17, 5 February 2018
The information on this page supplements the official manuals.
Contents
The Global menu lets you set the Tap Tempo operating mode:
- Average: averages the tempo to the last ten taps.
- Last Two: uses only the most recent two taps to determine the tempo.
When tapping the Tempo button or switch, the Tempo menu appears. It will disappear after a few seconds. You can specify in the Global menu how long it should stay on-screen.
Tempo: global or preset
You can specify in the Tempo menu whether you want tempo to be set globally (across all presets) or per preset.
Tempo LED accuracy
"The tempo LED is handled by a low-priority thread so it isn't rock solid and the higher the CPU usage the less solid it will be." source
Tempo is part of MIDI data
Tempo information is sent to other devices through MIDI syex. This can be disabled in the I/O menu (Send Realtime Sysex parameter).
Ticking tempo noise
Audible bleed-through of the tempo signal can occur when the MIDI cable is not properly shielded.
Metronome
The Axe-Fx II, AX8 and FX8 can emit a metronome signal. The metronome is located in the Tempo menu. You can start the metronome using a switch (assigned to the Metronome's MIDI CC) or through the Tempo menu. The metronome plays through Output 1 only.
The Axe-FX III does not provide a metronome.
Auto-activate a Delay using Tap Tempo
If the parameter Auto Delay in the Tempo menu is “ON,” any delay blocks that are bypassed will become active whenever a tempo is tapped in. This allows you to set the tempo and un-bypass your delay block(s) from a single footswitch.
MIDI CCs for Tempo and Metronome
- Tempo: CC 14
- Metronome: CC 122 (not on Axe-Fx III)
Using Tempo in effect blocks
Some effects let you assign parameters such as Time or Rate to a specific tempo, like 1/4 or 1/8 Dotted, instead of number of milliseconds. That will make the effect depend on the global or preset tempo. Tapping a different tempo will change the rate of the effect.
