October 2024: Fractal Audio's VP4 Virtual Pedalboard has been added to the wiki.
Difference between revisions of "Enhancer block"
Jump to navigation
Jump to search
| Line 7: | Line 7: | ||
=User contributions= | =User contributions= | ||
| − | ==Enhancer | + | ==Enhancer== |
* Firmware 5: "the new Enhancer uses multi-band techniques for a much more natural effect. Also, the effect is mono-compatible with no phasing problems when summing to mono. The effect both widens stereo signals and “stereoizes” mono signals. Low-cut and High-cut parameters allow control over the region of influence. Note that it is NOT recommended to use the Enhancer if just using one side of a stereo output as phasing effects may be encountered." [http://forum.fractalaudio.com/axe-fx-ii-bugs/48082-enhancer-issue.html More information] | * Firmware 5: "the new Enhancer uses multi-band techniques for a much more natural effect. Also, the effect is mono-compatible with no phasing problems when summing to mono. The effect both widens stereo signals and “stereoizes” mono signals. Low-cut and High-cut parameters allow control over the region of influence. Note that it is NOT recommended to use the Enhancer if just using one side of a stereo output as phasing effects may be encountered." [http://forum.fractalaudio.com/axe-fx-ii-bugs/48082-enhancer-issue.html More information] | ||
* Firmware 6.01: "Added “Classic” mode to Enhancer block which uses old Haas effect delay-based processing. The Type parameter selects between the new (Modern) and old (Classic) enhancer types." | * Firmware 6.01: "Added “Classic” mode to Enhancer block which uses old Haas effect delay-based processing. The Type parameter selects between the new (Modern) and old (Classic) enhancer types." | ||
| Line 15: | Line 15: | ||
* While a stereo input signal works best, the Enhancer can also "stereoize" an incoming mono signal. Of course, the output signal still has to be stereo. | * While a stereo input signal works best, the Enhancer can also "stereoize" an incoming mono signal. Of course, the output signal still has to be stereo. | ||
| − | == | + | ==Enhancer: avoiding phase cancellation== |
* When summing a stereo signal to mono, the Enhancer in Classic mode can cause [[Audio topics | phase cancellation]]. The Modern Mode is mono-compatible to prevent this. | * When summing a stereo signal to mono, the Enhancer in Classic mode can cause [[Audio topics | phase cancellation]]. The Modern Mode is mono-compatible to prevent this. | ||
| − | == | + | ==Enhancer: alternatives== |
* Cliff: "Another way would be to use the Delay block. Set the Mix to 100%, dial in the desired amount of delay and set Balance to full right." [http://forum.fractalaudio.com/axe-fx-ii-discussion/75709-30-ms-delay-but-nothing-else.html#post924932 Source] | * Cliff: "Another way would be to use the Delay block. Set the Mix to 100%, dial in the desired amount of delay and set Balance to full right." [http://forum.fractalaudio.com/axe-fx-ii-discussion/75709-30-ms-delay-but-nothing-else.html#post924932 Source] | ||
| − | == | + | ==Enhancer: widening the Panner== |
* Make the Panner effect appear “fuller” and “wider” (stereo only) by adding the Enhancer. | * Make the Panner effect appear “fuller” and “wider” (stereo only) by adding the Enhancer. | ||
[[category:Presets and effects]] | [[category:Presets and effects]] | ||
Revision as of 09:50, 11 April 2014
Contents
Manual
5.9 Enhancer (ENH) — 16.10 Mono and Stereo
User contributions
Enhancer
- Firmware 5: "the new Enhancer uses multi-band techniques for a much more natural effect. Also, the effect is mono-compatible with no phasing problems when summing to mono. The effect both widens stereo signals and “stereoizes” mono signals. Low-cut and High-cut parameters allow control over the region of influence. Note that it is NOT recommended to use the Enhancer if just using one side of a stereo output as phasing effects may be encountered." More information
- Firmware 6.01: "Added “Classic” mode to Enhancer block which uses old Haas effect delay-based processing. The Type parameter selects between the new (Modern) and old (Classic) enhancer types."
Enhancer: mono/stereo
- The Enhancer only works when your OUTPUT signal is stereo. Also, don't use it if you only use one channel (left or right) of a stereo signal.
- While a stereo input signal works best, the Enhancer can also "stereoize" an incoming mono signal. Of course, the output signal still has to be stereo.
Enhancer: avoiding phase cancellation
- When summing a stereo signal to mono, the Enhancer in Classic mode can cause phase cancellation. The Modern Mode is mono-compatible to prevent this.
Enhancer: alternatives
- Cliff: "Another way would be to use the Delay block. Set the Mix to 100%, dial in the desired amount of delay and set Balance to full right." Source
Enhancer: widening the Panner
- Make the Panner effect appear “fuller” and “wider” (stereo only) by adding the Enhancer.
