Read the Owners Manual first!

Difference between revisions of "Factory presets"

From Fractal Audio Wiki
Jump to navigation Jump to search
Line 1: Line 1:
 
==List==
 
==List==
 
* To get an up-to-date list of all factory presets, download the latest banks from [http://www.fractalaudio.com/support Support]. Start Axe-Edit > Axe-Manage and load the banks.
 
* To get an up-to-date list of all factory presets, download the latest banks from [http://www.fractalaudio.com/support Support]. Start Axe-Edit > Axe-Manage and load the banks.
* Here are screen grabs from version 9.xx factory banks.
+
* Here are screen grabs from version 10 factory banks.
  
 
[[File:BankA.jpg]]
 
[[File:BankA.jpg]]
 +
 +
----
  
 
[[File:BankB.jpg]]
 
[[File:BankB.jpg]]
 +
 +
----
  
 
[[File:BankC.jpg]]
 
[[File:BankC.jpg]]
Line 32: Line 36:
 
* When really digging in the strings, especially using a high-output humbucker, some clean presets may distort. Don't worry, they should probably be getting into distortion, based on their settings. If you don't like that, just turn down Drive or Master Volume in the Amp block.
 
* When really digging in the strings, especially using a high-output humbucker, some clean presets may distort. Don't worry, they should probably be getting into distortion, based on their settings. If you don't like that, just turn down Drive or Master Volume in the Amp block.
 
* If a factory presets makes the Out 1 Clip LED blink, its signal level is too hot. Turn down Level in the Amp block.
 
* If a factory presets makes the Out 1 Clip LED blink, its signal level is too hot. Turn down Level in the Amp block.
* Cliff: "Adam and I created the first 50 presets with the mantra "Quality above quantity". Rather than sifting through hundreds of mediocre presets, we just wanted to give 50 of the best amp sounds we could come up with. They should be usable "out of the box" and as a starting point for your own tone creations. We used a PRS and a Strat to make the presets. The Fenders were made with the Strat, the heavier stuff with the PRS. As with real amps, certain guitars work better with certain amps." [http://www.thegearpage.net/board/showpost.php?p=13002309&postcount=8 Source]
 
* Adam Cook (firmware 7): "We did try to dial in a bit more bite this time around as some folks complained the 6.0 presets had a bit of a "blanket on the speaker" quality at times and we did notice that occasionally when revisiting them. These adjustments were generally done just by tweaking the cab IR or mic choice on the cab IR. Most of the amp settings are very close to defaults. If you have a monitor setup that accentuates the highs they might seem a bit too bright. As always, please use your ears and adjust to taste." [http://forum.fractalaudio.com/axe-fx-ii-discussion/56135-fw-7-presets-hi-end-issue-solved.html#post707135 Source]
 
* Cliff (firmware 9.xx): "I went through all the "raw amp" presets and retweaked them. I've found that the new firmware really brings out the character of the cabs now. Cabs that I rarely used in the past really sound good with certain amps." [http://forum.fractalaudio.com/axe-fx-ii-discussion/61456-new-presets-v9-support-page-4.html#post764921 Source]
 
  
 
[[category:Presets and effects]]
 
[[category:Presets and effects]]
 
[[category:About the Axe-Fx II]]
 
[[category:About the Axe-Fx II]]

Revision as of 20:55, 6 April 2013

List

  • To get an up-to-date list of all factory presets, download the latest banks from Support. Start Axe-Edit > Axe-Manage and load the banks.
  • Here are screen grabs from version 10 factory banks.

File:BankA.jpg


File:BankB.jpg


File:BankC.jpg

Factory presets updates

  • Fractal Audio posts new versions of the factory presets on the Support page from time to time. Go here for update instructions: Factory presets, updating.

Listening to recordings of factory presets

How to audition the factory presets

  • If possible, play the factory presets in stereo. It makes a lot of difference and you'll hear the presets the right way.
  • Use a guitar with single coil pickups. The Axe-Fx is very sensitive to the type of guitar you're using.
  • Preset output levels can vary from preset to preset.
  • Some presets contain an ENH block (Enhancer) which is for stereo use only. If you're running mono and audio output is set to “Sum L+R”, Phase cancellation may occur.
  • Some presets include a Delay block with the Phase Rev parameter engaged. This is a stereo-only feature. If you're running in mono and audio output mode is set to “Sum L+R”, you may not hear any delay because of Phase cancellation. Switch off Phase Rev or select output mode “Copy L>R” instead.
  • When using stereo output mode "Copy L>R" you'll lose the part of the signal that's hardwired to the right channel.

Restoring factory presets

  • When saving your own presets you have to overwrite factory presets. You can restore the factory presets at any moment:
    • from onboard ROM (original three banks; probably outdated), or
    • from disk after downloading them from Support. They are also included with Axe-Edit. Go here for update instructions: Factory presets, updating.

More information about the factory presets

  • When hitting the strings in a normal manner on a guitar equipped with single coils, clean factory presets such as Bassman, Doubleverb, Shiva Clean should not distort.
  • When really digging in the strings, especially using a high-output humbucker, some clean presets may distort. Don't worry, they should probably be getting into distortion, based on their settings. If you don't like that, just turn down Drive or Master Volume in the Amp block.
  • If a factory presets makes the Out 1 Clip LED blink, its signal level is too hot. Turn down Level in the Amp block.