Read the Owners Manual first!
Difference between revisions of "Phaser block"
| Line 19: | Line 19: | ||
==Uni-vibe== | ==Uni-vibe== | ||
| − | The Vibe effect is available as a special mode of the Phaser block. | + | The Vibe effect is available as a special mode of the Phaser block. Engage Vibe Mode (or select the Classic Vibe type). |
The default settings are modeled after the Fulltone Deja-Vibe. [http://forum.fractalaudio.com/threads/need-help-with-some-sounds.109156/#post-1305852 source] | The default settings are modeled after the Fulltone Deja-Vibe. [http://forum.fractalaudio.com/threads/need-help-with-some-sounds.109156/#post-1305852 source] | ||
| + | |||
| + | [http://forum.fractalaudio.com/threads/vibe.138468/#post-1641918 AustinBuddy recreates the Shin-ei Vibe.] | ||
<blockquote>"You need it before the amp if you want the bump." [http://forum.fractalaudio.com/threads/recommendations-to-achieve-a-good-univibe-sound.104710/#post-1252527 source] </blockquote> | <blockquote>"You need it before the amp if you want the bump." [http://forum.fractalaudio.com/threads/recommendations-to-achieve-a-good-univibe-sound.104710/#post-1252527 source] </blockquote> | ||
Revision as of 12:04, 30 May 2018
Contents
Available on which Fractal Audio products
- Axe-Fx III: 2x.
- Axe-Fx II: 2x.
- AX8: 1x.
- FX8: 2x.
X/Y and channels
- Axe-Fx III: 4 channels.
- Axe-Fx II: yes.
- AX8: yes.
- FX8: yes.
Effect types
Uni-vibe
The Vibe effect is available as a special mode of the Phaser block. Engage Vibe Mode (or select the Classic Vibe type).
The default settings are modeled after the Fulltone Deja-Vibe. source
AustinBuddy recreates the Shin-ei Vibe.
"You need it before the amp if you want the bump." source
Tip: connect a pedal or switch (via an external controller) to the Rate parameter to control speed.
More information:
Barber Pole Phaser
Like the "Shepard" tone, this type gives the illusion of a never-ending cycle. Works best when placed at the end of the chain.
Mono or stereo
Phaser defaults to mono to prevent phase problems when used before an Amp block. To make it stereo, change the LFO Phase setting and place it after Drive, Amp and (mono) Cab.
Parameters
Parameters table
| Parameter | Axe-Fx III | Axe-Fx II | AX8, FX8 |
|---|---|---|---|
| Type | yes | ||
| Rate | yes | ||
| Tempo | yes | ||
| Depth | yes | ||
| Feedback | yes | ||
| Frequency | yes | ||
| Frequency Span | yes | ||
| Tone | yes | ||
| Phaser Mode | yes | ||
| Order | yes | ||
| LFO Type | yes | ||
| LFO Phase | yes | ||
| Bulb Bias | yes | ||
| Feedback Tap | yes | ||
| LFO Reset on Bypass | yes |
Order
Increase the Order parameter to simulate phasers such as the EHX Small stone and Mu-tron Bi-Phase.
Feedback Tap
"There is no feedback on a Script 90." source
LFO Bypass Reset
If LFO Bypass Reset is set to anything other than Off, the LFO will be reset to the selected phase whenever the block is bypassed. This allows synchronizing the sweep to the engagement of the effect.
Troubleshooting
Thump when engaging the Phaser
If engaging/bypassing the Phaser block causes an audible thump or gap, change input impedance to 1M (Axe-Fx II, III and FX8).
