October 2024: Fractal Audio's VP4 Virtual Pedalboard has been added to the wiki.
Difference between revisions of "Volume/Panner block"
Jump to navigation
Jump to search
| Line 1: | Line 1: | ||
[[image:volumeknob.png|link=]] | [[image:volumeknob.png|link=]] | ||
| − | =Vol/Pan: in the owner's manual= | + | =Vol/Pan: in the Axe-Fx II owner's manual= |
* [[media:5.33 Volume-Pan -VOL-.pdf |Axe-Fx II: 5.33 Vol/Pan [VOL]]] | * [[media:5.33 Volume-Pan -VOL-.pdf |Axe-Fx II: 5.33 Vol/Pan [VOL]]] | ||
| − | =Vol/Pan: | + | =Vol/Pan: supported by which Fractal Audio products?= |
* Axe-Fx II: yes. | * Axe-Fx II: yes. | ||
* FX8: yes. | * FX8: yes. | ||
| Line 11: | Line 11: | ||
* The Volume block offers various audio tapers. Cliff: "The number is the percentage at the halfway point. I.e. Log 20A means that the resistance is 20% at the halfway point in the travel. So if you put the knob at noon, the volume would be 20% of maximum (about -14 dB)." [http://forum.fractalaudio.com/axe-fx-ii-discussion/58160-volume-blk-volume-tapers.html#post727942 source] | * The Volume block offers various audio tapers. Cliff: "The number is the percentage at the halfway point. I.e. Log 20A means that the resistance is 20% at the halfway point in the travel. So if you put the knob at noon, the volume would be 20% of maximum (about -14 dB)." [http://forum.fractalaudio.com/axe-fx-ii-discussion/58160-volume-blk-volume-tapers.html#post727942 source] | ||
* To simulate a Log taper in a modifier menu, set "Mid" in the modifier menu to 20%. Adjust Slope to avoid the dead zone. | * To simulate a Log taper in a modifier menu, set "Mid" in the modifier menu to 20%. Adjust Slope to avoid the dead zone. | ||
| + | |||
| + | =Vol/Pan: processing one side of the signal= | ||
| + | * Just like the Amp block and Drive blocks, Vol/Pan is able to operate on the left, right or both (stereo) sides of the input signal (Input Select parameter). It then can send the signal to either side (Balance parameter) or keep it stereo. | ||
=Vol/Pan: automating volume swells= | =Vol/Pan: automating volume swells= | ||
| − | * To automate volume swells (like a Boss Slow Gear pedal), use a Volume block | + | * To automate volume swells (like a Boss Slow Gear pedal), use a Volume block and attach Envelope to the Volume parameter. You can also copy the block and Envelope settings from a factory preset (such as Auto Swell Pongverb, Ganymede, Atmosphere on the Axe-Fx II. The Envelope's Attack parameter and the Volume block's Taper parameter determine the swell rate. |
| − | * Alternatively, for example to achieve Van Halen's Cathedral effect, set the | + | * Alternatively, for example to achieve Van Halen's Cathedral effect, set the Input Noise Gate to a low Threshold (i.e. -49), set Ratio between 3.3 and 4, and Attack and Release to 31 ms. |
| − | =Vol/Pan: | + | =Vol/Pan: use it as a noise gate= |
| − | * | + | * The Volume block can operate as a noise gate. Attach the Volume parameter to the Envelope controller. When you don't hit the strings, the input signal is muted. |
| − | =Vol/Pan: | + | =Vol/Pan: use it as a router/switcher= |
| − | * The | + | * The Volume block doesn't require much CPU. This makes it a good tool to solve routing issues. By setting its Bypass parameter to mute and placing it at the start of a branch, you can enable or disable a certain routing within a preset, depending on the state of the Volume block. You can engage or bypass the block per preset scene. |
| − | =Vol/Pan: | + | =Vol/Pan: various tips= |
* [http://forum.fractalaudio.com/fx8-discussion/91611-fx8-axe-fx-ii-effects-compression-volume-gate-cmp-vol-gte.html FX8 and Axe-Fx II effects threads: Compression, Volume, Gate (CMP, VOL, GTE)] | * [http://forum.fractalaudio.com/fx8-discussion/91611-fx8-axe-fx-ii-effects-compression-volume-gate-cmp-vol-gte.html FX8 and Axe-Fx II effects threads: Compression, Volume, Gate (CMP, VOL, GTE)] | ||
Revision as of 13:02, 4 May 2015
Contents
Vol/Pan: in the Axe-Fx II owner's manual
Vol/Pan: supported by which Fractal Audio products?
- Axe-Fx II: yes.
- FX8: yes.
Vol/Pan: audio tapers
- The Volume block offers various audio tapers. Cliff: "The number is the percentage at the halfway point. I.e. Log 20A means that the resistance is 20% at the halfway point in the travel. So if you put the knob at noon, the volume would be 20% of maximum (about -14 dB)." source
- To simulate a Log taper in a modifier menu, set "Mid" in the modifier menu to 20%. Adjust Slope to avoid the dead zone.
Vol/Pan: processing one side of the signal
- Just like the Amp block and Drive blocks, Vol/Pan is able to operate on the left, right or both (stereo) sides of the input signal (Input Select parameter). It then can send the signal to either side (Balance parameter) or keep it stereo.
Vol/Pan: automating volume swells
- To automate volume swells (like a Boss Slow Gear pedal), use a Volume block and attach Envelope to the Volume parameter. You can also copy the block and Envelope settings from a factory preset (such as Auto Swell Pongverb, Ganymede, Atmosphere on the Axe-Fx II. The Envelope's Attack parameter and the Volume block's Taper parameter determine the swell rate.
- Alternatively, for example to achieve Van Halen's Cathedral effect, set the Input Noise Gate to a low Threshold (i.e. -49), set Ratio between 3.3 and 4, and Attack and Release to 31 ms.
Vol/Pan: use it as a noise gate
- The Volume block can operate as a noise gate. Attach the Volume parameter to the Envelope controller. When you don't hit the strings, the input signal is muted.
Vol/Pan: use it as a router/switcher
- The Volume block doesn't require much CPU. This makes it a good tool to solve routing issues. By setting its Bypass parameter to mute and placing it at the start of a branch, you can enable or disable a certain routing within a preset, depending on the state of the Volume block. You can engage or bypass the block per preset scene.
