Difference between revisions of "MIDI SysEx"

Revision as of 04:15, 8 April 2013

About MIDI System Exclusive (SysEx) messages

If you're a MIDI expert, you can use SysEx messages (MIDI System Exclusive) to control the Axe-Fx II.
To learn more about MIDI, read this article.
To learn more about SysEx, read this article.

SysEx messages for Ultra

Ultra-specific SysEx information has been accurately acquired and organized by forum member GM Arts: here.
Information about SysEx commands for retrieving Preset/Effect bypass states is here.

SysEx messages for Axe-Fx II

Many Axe-Fx II SysEx messages are similar to Standard/Ultra messages documented here.
Model ID is 3.
All messages must be sent with checksums.
Responses for some key messages are different. Information about SysEx commands for retrieving Preset names and Preset/Effect bypass states is here.
All Axe-Fx II SysEx messages have the same header as follows:

0xF0 sysex start 0x00 Manf. ID byte0 0x01 Manf. ID byte1 0x74 Manf. ID byte2 0x03 Model # (Axe-Fx II = 0x03) 0xdd Function ID

*Function IDs*
Function ID	Function Name
0x02	MIDI_GET_PARAMETER, MIDI_SET_PARAMETER
0x07	MIDI_GET_MODIFIER, MIDI_SET_MODIFIER
0x08	MIDI_GET_FIRMWARE_VERSION
0x0D	MIDI_TUNER_INFO
0x0E	MIDI_GET_PRESET_EFFECT_BLOCKS_AND_CC_AND_BYPASS_STATE
0x0F	MIDI_GET_PRESET_NAME
0x10	MIDI_TEMPO_BEAT
0x14	MIDI_GET_PRESET_NUMBER
0x20	MIDI_GET_ROUTING_GRID_LAYOUT
0x23	MIDI_LOOPER_STATUS_ENABLE, MIDI_LOOPER_STATUS
0x29	MIDI_SET_SCENE_NUMBER

MIDI_GET_PARAMETER, MIDI_SET_PARAMETER

Message format:

0xF0 sysex start 0x00 Manf. ID byte0 0x01 Manf. ID byte1 0x74 Manf. ID byte2 0x03 Model # 0x02 Function ID (2) 0xdd effect ID bits 6-0 0xdd effect ID bits 13-7 0xdd parameter ID bits 6-0 0xdd parameter ID bits 13-7 0xdd parameter value bits 6-0 0xdd parameter value bits 13-7 0xdd parameter value bits 15-14 0x00 0=query value, 1=set value 0xdd checksum 0xF7 sysex end

Response format:

0xF0 sysex start 0x00 Manf. ID byte0 0x01 Manf. ID byte1 0x74 Manf. ID byte2 0x03 Model # 0x02 Function ID (2) 0xdd effect ID bits 6-0 0xdd effect ID bits 13-7 0xdd parameter ID bits 6-0 0xdd parameter ID bits 13-7 0xdd parameter value bits 6-0 0xdd parameter value bits 13-7 0xdd parameter value bits 15-14 0xdd 0xdd 0xdd 0xdd 0xdd 0xdd null-terminated string byte0 0xdd byte1 ... 0x00 null character 0xdd checksum 0xF7 sysex end

MIDI_GET_MODIFIER, MIDI_SET_MODIFIER

Message format:

0xF0 sysex start 0x00 Manf. ID byte0 0x01 Manf. ID byte1 0x74 Manf. ID byte2 0x03 Model # 0x07 Function ID (7) 0xdd effect ID bits 6-0 0xdd effect ID bits 13-7 0xdd parameter ID bits 6-0 0xdd parameter ID bits 13-7 0xdd modifier parameter selector ID bits 6-0 0xdd 0 0xdd modifier value bits 6-0 0xdd modifier value bits 13-7 0xdd modifier value bits 15-14 0x00 0=query value, 1=set value 0xdd checksum 0xF7 sysex end

Response format:

0xF0 sysex start 0x00 Manf. ID byte0 0x01 Manf. ID byte1 0x74 Manf. ID byte2 0x03 Model # 0x02 Function ID (2) 0xdd effect ID bits 6-0 0xdd effect ID bits 13-7 0xdd parameter ID bits 6-0 0xdd parameter ID bits 13-7 0xdd modifier parameter selector ID bits 6-0 0xdd 0 0xdd modifier value bits 6-0 0xdd modifier value bits 13-7 0xdd modifier value bits 15-14 0xdd null-terminated string byte0 0xdd byte1 ... 0x00 null character 0xdd checksum 0xF7 sysex end

Modifier Parameter Selector IDs:

0x0 modifier source 0x1 min 0x2 max 0x3 start 0x4 mid 0x5 end 0x6 slope 0x7 damping 0x8 ? 0x9 ? 0xA auto engage 0xB pc reset 0xC off val 0xD scale 0xE offset

MIDI_GET_FIRMWARE_VERSION

Message format:

0xF0 sysex start 0x00 Manf. ID byte0 0x01 Manf. ID byte1 0x74 Manf. ID byte2 0x03 Model # 0x08 Function ID (8) 0xdd checksum 0xF7 sysex end

Response format:

0xF0 sysex start 0x00 Manf. ID byte0 0x01 Manf. ID byte1 0x74 Manf. ID byte2 0x03 Model # 0x08 Function ID (8) 0xdd Firmware Version major number 0xdd Firmware Version minor number 0xdd 0xdd 0xdd 0xdd 0xdd checksum 0xF7 sysex end

MIDI_TUNER_INFO

This message is broadcast when the Tuner enabled. Note that the Axe-FX II does not include the checksum byte in this message:

0xF0 sysex start 0x00 Manf. ID byte0 0x01 Manf. ID byte1 0x74 Manf. ID byte2 0x03 Model # 0x0D Function ID (0x0D) 0xdd Note (0=A; 1=Bb; 2=B; etc.) 0xdd String number (0=high E string; 5=low E string) 0xdd Tuner data (value of 63 indicates 'perfectly in tune') 0xF7 sysex end

MIDI_GET_PRESET_EFFECT_BLOCKS_AND_CC_AND_BYPASS_STATE

Message format:

0xF0 sysex start 0x00 Manf. ID byte0 0x01 Manf. ID byte1 0x74 Manf. ID byte2 0x03 Model # 0x0E Function ID (0x0E) 0xdd checksum 0xF7 sysex end

Response format:

0xF0 sysex start 0x00 Manf. ID byte0 0x01 Manf. ID byte1 0x74 Manf. ID byte2 0x03 Model # 0x0E Function ID (0x0E) Information about each effect block in preset follows, using 5 bytes for each effect block in the preset 0xdd Status Bits Bit 0: 0=Bypassed, 1=Enabled Bit 1: 0=Y, 1=X Bit 2: Bit 3: Bit 4: Bit 5: Bit 6: 0xdd IA CC Number LSB Bit 0: Bit 1: IA_CC_Number Bit 0 Bit 2: IA_CC_Number Bit 1 Bit 3: IA_CC_Number Bit 2 Bit 4: IA_CC_Number Bit 3 Bit 5: IA_CC_Number Bit 4 Bit 6: IA_CC_Number Bit 5 0xdd IA CC Number MSB Bit 0: IA_CC_Number Bit 6 Bit 1: IA_CC_Number Bit 7 Bit 2: Bit 3: Bit 4: Bit 5: Bit 6: 0xdd Effect ID LSB Bit 0: Bit 1: Bit 2: Bit 3: Effect_ID Bit 0 Bit 4: Effect_ID Bit 1 Bit 5: Effect_ID Bit 2 Bit 6: Effect_ID Bit 3 0xdd Effect ID MSB Bit 0: Effect_ID Bit 4 Bit 1: Effect_ID Bit 5 Bit 2: Effect_ID Bit 6 Bit 3: Effect_ID Bit 7 Bit 4: Bit 5: Bit 6: ... (Additional 5-byte chunks, one for each block in the preset) 0xdd checksum 0xF7 sysex end

MIDI_GET_PRESET_NAME

Message format:

0xF0 sysex start 0x00 Manf. ID byte0 0x01 Manf. ID byte1 0x74 Manf. ID byte2 0x03 Model # 0x0F Function ID (0x0F) 0xdd checksum 0xF7 sysex end

Response format:

Function number: 14 Example: F0 0 1 74 3 14 0 1 13 0 FF --> to set the current preset (edit buffer) to preset 0 (1 if DISPLAY OFFSET activated) F0 0 1 74 3 14 1 0 13 0 FF --> to set the current preset (edit buffer) to preset 128 (129 if DISPLAY OFFSET activated) Send from AXE-FX to AXE-EDIT and MFC-101

Calculating the SysEx checksum for the Axe-FX II

As mentioned above, the Axe-FX II units require a checksum to be added to the end of the SysEx string that is sent to it (before the terminating F7 byte) as a verification step.
In order to calculate the checksum, you basically have to XOR every byte from the start of the SysEx message, up to the character BEFORE the terminating F7 byte. For example, to send the following SysEx message (to fetch a preset name):

F0 00 01 74 03 0F F7

We would have to XOR all the byte values from the starting 'F0' to the '0F' which is the second last byte:

0xF0 ^ 0x00 ^ 0x01 ^ 0x74 ^ 0x03 ^ 0x0F = 0x89

Then, we would need to strip the leftmost bit from the result (by ANDing it to 0x7F):

0x89 && 0x7F = 0x09

And, we add this byte (actually, a septet now) to the end of the SysEx string, BEFORE the terminating F7:

F0 00 01 74 03 0F 09 F7

Obviously, in a 'static' SysEx message like above, you do not have to recalculate the checksum each time as it will always be '09' as the rest of the message does not change, but if you are sending a SysEx string to change a parameter value etc. then you will have to calculate the checksum on the fly as byte values towards the end of the SysEx string will be different each time.

Obtaining Parameter Values via SysEx Messages

The old Standard/Ultra devices used to store the parameter values on *most* knobs as 0-254. This was split into two bytes, XX YY where XX was the lowest 4 bits of the value, and YY was the highest 4 bits. Pretty simple.

The new Axe-II now has more granular control over *most* knobs, with the values going from 0-65534. This requires a full 16 bits to store. The problem is that the MIDI specifications means you can only transmit values using 7 bits as the highest bit of each byte must be a zero.

To get around this, the Axe-II uses THREE bytes to transmit the values XX YY ZZ where XX is the lowest 7 bits of the data, YY is the 8th to the 14th bit of the data, and ZZ is the remaining top two bits of the data.

So, if you had the value 52421 on a knob, then this would be represented by the 16 bits: 1100110011000101

If you split this into segments of length 2/7/7 to store in ZZ/YY/XX: 11 0011001 1000101

So XX gets the last segment: 01000101 And YY gets the middle segment: 00011001 And ZZ gets the first segment: 00000011

You will also have to back-calculate the respective knob values to the 16 bit values. For example, a knob that goes from 0 - 10, 0 would of course be 0, but 10 would be 65534. From there, you would work out that 5 is 32767 and 7 would be about 45871 etc.

Axe Fx II SysEx Information for loading IRs

The information below was provided by former forum member LMO.
The Axe Fx II supports 2040-point impulse responses that are packaged for download in a series of 66 MIDI SysEx messages, as follows:

MIDI_START_IR_DOWNLOAD

Prepare the Axe-Fx II to receive impulse response data

Message Format:

0xF0 sysex start 0x00 manufacturing ID byte 0 0x01 manufacturing ID byte 1 0x74 manufacturing ID byte 2 0x03 model number 0x7A function ID 0x20 0x00 0x10 0xdd checksum 0xF7 sysex end

MIDI_G2_IR_DATA

There are 64 SysEx messages, each containing 32 chunks of data. Each chunk consists of five bytes and can hold either four text characters or one 32-bit IR data sample.

The first data message sent includes 8 chunks of text that specify the 32-character IR name, and 24 chunks of IR data. The subsequent 63 data messages each contain 32 data samples for a total of 2040 samples.

Message Format:

0xF0 sysex start 0x00 manufacturing ID byte 0 0x01 manufacturing ID byte 1 0x74 manufacturing ID byte 2 0x03 model number 0x7B function ID 0x20 0x00 0xdd data chunk byte 0 0xdd data chunk byte 1 0xdd data chunk byte 2 0xdd data chunk byte 3 0xdd data chunk byte 4 --- 31 additional five byte data chunks --- 0xdd checksum 0xF7 sysex end

MIDI_CLOSE_IR_DOWNLOAD

Terminate the IR download sequence

Message Format:

0xF0 sysex start 0x00 manufacturing ID byte 0 0x01 manufacturing ID byte 1 0x74 manufacturing ID byte 2 0x03 model number 0x7C function ID 0xdd encoded checksum byte 0 for IR data 0xdd encoded checksum byte 1 for IR data 0xdd encoded checksum byte 2 for IR data 0xdd encoded checksum byte 3 for IR data 0xdd encoded checksum byte 4 for IR data 0xdd checksum 0xF7 sysex end

Data Chunk Encoding Scheme

The data encoding scheme translates four octets into five septets. Each septet occupies the lower seven bits of a byte, with the most significant bit set to 0.

octet is one byte containing 8 bits of data septet is one byte containing 7 bits of data byte_chunk = (data[0] & 0xFF )<< 24 | (data[1] & 0xFF )<< 16 | (data[2] & 0xFF )<< 8 (data[3] & 0xFF; convert four octets to five septets septet[0] = byte_chunk & 0xFF; septet[1] = byte_chunk >> 7 & 0xFF; septet[2] = byte_chunk >> 14 & 0xFF; septet[3] = byte_chunk >> 21 & 0xFF; septet[4] = byte_chunk >> 28 & 0xFF;

Effect IDs

100 Comp 1 101 Comp 2 102 GEQ 1 103 GEQ 2 104 PEQ 1 105 PEQ 2 106 Amp 1 107 Amp 2 108 Cab 1 109 Cab 2 110 Reverb 1 111 Reverb 2 112 Delay 1 113 Delay 2 114 Multi Delay 1 115 Multi Delay 2 116 Chorus 1 117 Chorus 2 118 Flanger 1 119 Flanger 2 120 Rotary 1 121 Rotary 2 122 Phaser 1 123 Phaser 2 124 Wah 1 125 Wah 2 126 Formant 127 Vol 1 128 Pan Trem 1 129 Pan Trem 2 130 Pitch 1 131 Filter 1 132 Filter 2 133 Drive 1 134 Drive 2 135 Enhancer 1 136 Effects Loop 137 Mixer 1 138 Mixer 2 139 Noise Gate 140 Output 141 Controllers 142 FB Send 143 FB Return 144 Synth 1 145 Synth 2 146 Vocoder 147 Megatap Dly 148 Crossover 1 149 Crossover 2 150 Gate Exp 1 151 Gate Exp 2 152 Ring Mod 153 Pitch 2 154 MB Comp 1 155 MB Comp 2 156 Quad Cho 1 157 Quad Cho 2 158 Resonator 1 159 Resonator 2 160 GEQ 3 161 GEQ 4 162 PEQ 3 163 PEQ 4 164 Filter 3 165 Filter 4 166 Vol 2 167 Vol 3 168 Vol 4 169 Looper 170 Tone Match

@@ Line 33: / Line 33: @@
 |-
 |0x07
-|MIDI_GET_MODIFIER, MIDI_SET_MODIFIER
+|[[#MIDI_GET_MODIFIER, MIDI_SET_MODIFIER|MIDI_GET_MODIFIER, MIDI_SET_MODIFIER]]
 |-
 |0x08
@@ Line 110: / Line 110: @@
 :0xdd   checksum
 :0xF7   sysex end
+</tt>
+===MIDI_GET_MODIFIER, MIDI_SET_MODIFIER===
+Message format:
+<tt>
+:0xF0   sysex start
+:0x00   Manf. ID byte0
+:0x01   Manf. ID byte1
+:0x74   Manf. ID byte2
+:0x03   Model #
+:0x07   Function ID (7)
+:0xdd   effect ID bits 6-0
+:0xdd   effect ID bits 13-7
+:0xdd   parameter ID bits 6-0
+:0xdd   parameter ID bits 13-7
+:0xdd   modifier parameter selector ID bits 6-0
+:0xdd   0
+:0xdd   modifier value bits 6-0
+:0xdd   modifier value bits 13-7
+:0xdd   modifier value bits 15-14
+:0x00   0=query value, 1=set value
+:0xdd   checksum
+:0xF7   sysex end
+</tt>
+Response format:
+<tt>
+:0xF0   sysex start
+:0x00   Manf. ID byte0
+:0x01   Manf. ID byte1
+:0x74   Manf. ID byte2
+:0x03   Model #
+:0x02   Function ID (2)
+:0xdd   effect ID bits 6-0
+:0xdd   effect ID bits 13-7
+:0xdd   parameter ID bits 6-0
+:0xdd   parameter ID bits 13-7
+:0xdd   modifier parameter selector ID bits 6-0
+:0xdd   0
+:0xdd   modifier value bits 6-0
+:0xdd   modifier value bits 13-7
+:0xdd   modifier value bits 15-14
+:0xdd   null-terminated string byte0
+:0xdd   byte1
+:...
+:0x00   null character
+:0xdd   checksum
+:0xF7   sysex end
+</tt>
+Modifier Parameter Selector IDs:
+<tt>
+:0x0   modifier source
+:0x1   min
+:0x2   max
+:0x3   start
+:0x4   mid
+:0x5   end
+:0x6   slope
+:0x7   damping
+:0x8   ?
+:0x9   ?
+:0xA   auto engage
+:0xB   pc reset
+:0xC   off val
+:0xD   scale
+:0xE   offset
 </tt>

Difference between revisions of "MIDI SysEx"

Revision as of 04:15, 8 April 2013

Contents

About MIDI System Exclusive (SysEx) messages

SysEx messages for Ultra

SysEx messages for Axe-Fx II

MIDI_GET_PARAMETER, MIDI_SET_PARAMETER

MIDI_GET_MODIFIER, MIDI_SET_MODIFIER

MIDI_GET_FIRMWARE_VERSION

MIDI_TUNER_INFO

MIDI_GET_PRESET_EFFECT_BLOCKS_AND_CC_AND_BYPASS_STATE

MIDI_GET_PRESET_NAME

MIDI_TEMPO_BEAT

MIDI_GET_PRESET_NUMBER

MIDI_GET_ROUTING_GRID_LAYOUT

MIDI_LOOPER_STATUS_ENABLE, MIDI_LOOPER_STATUS

MIDI_SET_SCENE_NUMBER

MIDI_SET_PRESET

Calculating the SysEx checksum for the Axe-FX II

Obtaining Parameter Values via SysEx Messages

Axe Fx II SysEx Information for loading IRs

Effect IDs

Navigation menu

Personal tools

Namespaces

Variants

Views

More

Search

Navigation

Categories

Contribute

Tools