October 2024: Fractal Audio's VP4 Virtual Pedalboard has been added to the wiki.
Difference between revisions of "Realtime Analyzer block"
| (5 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
__TOC__ | __TOC__ | ||
| − | = | + | =Realtime Analyzer block= |
| − | + | '''Axe-Fx III''': 1 block, no channels<BR> | |
| − | + | '''FM3''': n/a<BR> | |
| − | + | '''FM9''': n/a<BR> | |
| + | '''VP4''': n/a | ||
| − | + | '''Axe-Fx II''': n/a<BR> | |
| − | + | '''AX8''': n/a<BR> | |
| − | + | '''FX8''': n/a | |
=About the RTA= | =About the RTA= | ||
| Line 28: | Line 29: | ||
</blockquote> | </blockquote> | ||
| − | = | + | =Position on the grid= |
The RTA block requires an input signal only and doesn't transmit any signal, so its output doesn't need to be connected. | The RTA block requires an input signal only and doesn't transmit any signal, so its output doesn't need to be connected. | ||
| − | =Use RTA to | + | =Use RTA to visualize the audio spectrum= |
| − | The RTA | + | The RTA visualizes the audio spectrum. |
To view the display, scroll to the RTA block and press Edit. | To view the display, scroll to the RTA block and press Edit. | ||
| Line 62: | Line 63: | ||
# Set the Synth Type = Sine, Tracking = Off, Frequency = 1000 Hz. | # Set the Synth Type = Sine, Tracking = Off, Frequency = 1000 Hz. | ||
# Connect an instrument cable from Output 3 (left or right) to the Instrument Input. | # Connect an instrument cable from Output 3 (left or right) to the Instrument Input. | ||
| − | # Set the Input 1 / Instrument Level in the I/O | + | # Set the Input 1 / Instrument Level in the I/O menu to 50%. |
# Turn the Out 3 Level knob all the way up. | # Turn the Out 3 Level knob all the way up. | ||
# The Input 1 yellow LED should be lit. Red should not be lit. Go to the RTA block Config tab. Set Bands to 128, Window to Blackman. Go to the RTA tab. There should be a narrow spike at 1 kHz (three bands). There should be no other bands showing power except maybe a little noise at the highest bands. The spike at 1 kHz should be about 2 1/4 divisions below full-scale. | # The Input 1 yellow LED should be lit. Red should not be lit. Go to the RTA block Config tab. Set Bands to 128, Window to Blackman. Go to the RTA tab. There should be a narrow spike at 1 kHz (three bands). There should be no other bands showing power except maybe a little noise at the highest bands. The spike at 1 kHz should be about 2 1/4 divisions below full-scale. | ||
Latest revision as of 10:41, 9 November 2024
Contents
Realtime Analyzer block
Axe-Fx III: 1 block, no channels
FM3: n/a
FM9: n/a
VP4: n/a
Axe-Fx II: n/a
AX8: n/a
FX8: n/a
About the RTA
The RTA block is available on the Axe-Fx only.
FRACTAL AUDIO QUOTES
[1] The RTA is a Fourier Transform.
[2] The RTA block is a "constant Q" analyzer. White noise increases by 3dB/octave. The two tones are equal in amplitude. Therefore you should see a rising slope on the noise and the tones at equal amplitude.
Position on the grid
The RTA block requires an input signal only and doesn't transmit any signal, so its output doesn't need to be connected.
Use RTA to visualize the audio spectrum
The RTA visualizes the audio spectrum.
To view the display, scroll to the RTA block and press Edit.
It also makes for a great dynamic display during performances.
Use RTA to fight feedback
The RTA can point out frequencies where undesired feedback occurs. Turn the Value knob to select the desired band, and the frequency of the selected band will be displayed in the upper left corner. You can then use a PEQ to cut frequencies.
FRACTAL AUDIO QUOTES
[3] Use it to identify problem frequencies or as a spiffy screen saver.
Use RTA to test hardware I/O
The RTA can be used to test the hardware I/O. For example, to test the Instrument input:
FRACTAL AUDIO QUOTES [4]
- Go to a blank preset.
- Create a chain that connects Input 1 to the RTA block. On a separate row create a chain where the Synth block feeds Output 3.
- Set the Synth Type = Sine, Tracking = Off, Frequency = 1000 Hz.
- Connect an instrument cable from Output 3 (left or right) to the Instrument Input.
- Set the Input 1 / Instrument Level in the I/O menu to 50%.
- Turn the Out 3 Level knob all the way up.
- The Input 1 yellow LED should be lit. Red should not be lit. Go to the RTA block Config tab. Set Bands to 128, Window to Blackman. Go to the RTA tab. There should be a narrow spike at 1 kHz (three bands). There should be no other bands showing power except maybe a little noise at the highest bands. The spike at 1 kHz should be about 2 1/4 divisions below full-scale.
Use RTA to measure devices
The RTA can be used to measure the output of other equipment, in conjunction with the Synth block. For example, to measure the frequency response of an external EQ or distortion pedal, set the Synth block to Pink Noise, send the Synth's signal through the pedal and back again, and use the RTA to measure and see the response.
