MIDI SysEx

System Exclusive messages

If you're a MIDI expert, you can use SysEx messages (MIDI System Exclusive) to control Fractal Audio devices.

Learn more about SysEx

Discussion about Fractal Audio's SysEx implementation

Firmware Ares and later provides MIDI support for 3rd-party devices to set and/or get scene, channel, bypass, scene names, preset names, tuner data, tempo data, via System Exclusive messages.

Read this: Axe-Fx III MIDI for Third-Party Devices

Axe-Fx Standard and Axe-Fx Ultra

Ultra-specific SysEx information from forum member GM Arts

SysEx commands for retrieving Preset/Effect bypass states

Axe-Fx III and FM3

SysEx commands for control of the Axe-Fx III and FM3 through third-party MIDI devices is documented in this guide: Axe-Fx III MIDI for Third-Party Devices

SysEx Model number per device

The numbers below refer to the processors.

• 0x00 Axe-Fx Standard
• 0x01 Axe-Fx Ultra
• 0x02 MFC-101
• 0x03 Axe-Fx II
• 0x04 MFC-101 mk3
• 0x05 FX8
• 0x06 Axe-Fx II XL
• 0x07 Axe-Fx II XL+
• 0x08 AX8
• 0x0A FX8 mk2
• 0x10 Axe-Fx III
• 0x11 FM3
• 0x12 FM9

MIDI SysEx Functions

Many Axe-Fx II SysEx messages are similar to Standard/Ultra messages: documented here

The messages documented here are compatible between Axe-Fx II, Axe-Fx II XL, Axe-Fx II XL+ and AX8. FX8 messages are not documented.

Note, many examples on this page are using 3 for the Model #.

All messages you send must be sent with Checksums, but not all response messages will have a Checksum, those documented here will specify if a Checksum is not included.

All Axe-Fx II/AX8 SysEx messages have the same HEADER as follows:

0xF0 sysex start

0x00 Manf. ID byte0

0x01 Manf. ID byte1

0x74 Manf. ID byte2

0xdd Model #

The byte after the Model # will always be the Function ID.

The last byte of each message will be 0xF7, the Checksum is the byte before 0xF7

Here's an example of a sysex message, in this example the AX8 is responding with the preset number, function 0x14 GET_PRESET_NUMBER

[0xF0, 0x00, 0x01, 0x74, 0x08, 0x14, 0x00, 0x00, 0x19, 0xF7];

GET_FIRMWARE_VERSION

This message responds with the firmware version, also this acts as a "Greeting" message, only after the Axe FX II has received a firmware version request it will start sending message 0x21 FRONT_PANEL_CHANGE_DETECTED, if you're writing an app or foot controller that will need to be in sync then the first thing you want to do is request the firmware version so that message 0x21 is sent when changes happen on the front panel. Keep in mind, if you do this you will need to "Disconnect" from the hardware when your app closes by sending function 0x42 DISCONNECT_FROM_CONTROLLER

Message format:

HEADER BYTES

0x08 Function ID (0x08)

0xdd Checksum

0xF7 SysEx End

Response format:

HEADER BYTES

0x08 Function ID (0x08)

0xdd Firmware Version major number

0xdd Firmware Version minor number

0xdd

0xdd

0xdd

0xdd

0xdd Checksum

0xF7 SysEx End

FRONT_PANEL_CHANGE_DETECTED

This message is sent to notify you that something may have changed on the hardware, and is the message that causes Axe-Edit/AX8-Edit to "Pause Communication". This message is notifies the editor that something changed and that it should reload the data for that preset, and is why you get the PAUSE overlay on the editor. When you click that overlay the Editor will re-request all the preset data it needs to keep the editor in sync with the hardware.

For example if you select a block on the Axe FX II, say, the Filter block, and you change the gain, then the Axe FX will send this message.

This message is sent about 400ms after the action was complete.

Another example, on the AX8, if you use the Amp Controls on the front panel to change the Gain then you will receive this message. This message is also sent if you press a footswitch that changes a scene/preset/block bypass/XY.

This message is only sent by the hardware if you requested the Firmware version. Read 0x08 GET_FIRMWARE_VERSION for more information.

Message format:

HEADER BYTES

0x21 Function ID (0x21)

0xdd Checksum

0xF7 SysEx End

DISCONNECT_FROM_CONTROLLER

This message should be sent when you quit an application connected to the Axe Fx if your application sent the 0x08 GET_FIRMWARE_VERSION message. See the 0x08 GET_FIRMWARE_VERSION section for more information.

Message format:

HEADER BYTES

0x42 Function ID (0x42)

0xdd Checksum

0xF7 SysEx End

GET_MIDI_CHANNEL

This message message replies with the MIDI channel set under SETUP > I/O > MIDI > MIDI CHANNEL.

Message format:

HEADER BYTES

0x17 Function ID (0x17)

0xdd Checksum

0xF7 SysEx End

Response format:

HEADER BYTES

0x17 Function ID (0x17)

0xdd Midi Channel (single byte)

0xdd Checksum

0xF7 SysEx End

TUNER_INFO

This message is broadcast when the Tuner is engaged. Note that the Axe-FX II does not include the checksum byte in this message:

HEADER BYTES

0x0D Function ID (0x0D)

0xdd Note (0=A; 1=Bb; 2=B; etc.)

0xdd String number (0=high E string; 5=low E string)

0xdd Tuner data (value of 63 indicates 'perfectly in tune')

0xF7 SysEx End

TUNER_TOGGLE

To turn the tuner on/off you send a MIDI Control Change (CC). The CC value is the same that you assign on the Axe-Fx II in the same channel your Axe-Fx II is set to.

The default CC for the tuner is 15. Send the value 0 to turn the tuner off, any value of 64 or higher to turn it on.

You can get the MIDI Channel of your Axe-Fx with GET_MIDI_CHANNEL.

METRONOME_TOGGLE

To turn the metronome on/off you send a MIDI Control Change (CC). The CC value is the same you assign on the Axe-Fx II in the same channel your Axe-Fx II is set to.

Send the value 0 to turn the metronome off, any value of 64 or higher to turn it on.

You can get the MIDI channel of your Axe-Fx with GET_MIDI_CHANNEL.

NOTE that the metronome's level can not be edited via MIDI.

PRESET_BLOCKS_DATA

This message returns a 32-bit unsigned integer split into five MIDI words for each block loaded onto the preset. That is, if the amp block is loaded you will get five bytes with data for the amp block, etc.

The message contains five important pieces of data:

The block's current Bypass state (0 if bypassed, 1 if engaged).

The block's current X/Y state (0 if Y, 1 if X).

The block's ID (number ranging from 100 to 170).

The block's bypass CC# (if the value is 0 or more than 127, it means the block doesn't have a CC# assigned).

The block's XY CC# (if the value is 0 or more than 127, it means the block doesn't have a CC# assigned or doesn't have X/Y).

Request format:

HEADER BYTES

0x0E Function ID (0x0E)

0xdd Checksum

0xF7 SysEx End

Response format: (response doesn't have a checksum)

HEADER BYTES

0x0E Function ID (0x0E)

Information about each effect block in preset follows, using 5 bytes for each effect block in the preset

0xdd Byte 1 (flags) uint32_t LSB

Bit 0: 0 = Bypassed, 1 = Engaged

Bit 1: 0 = Y, 1 = X

Bit 2: unused

Bit 3: unused

Bit 4: unused

Bit 5: unused

Bit 6: unused

0xdd Byte 2 (bypass cc# number LSB)

Bit 0: unused (Bit 7 for the byte above)

Bit 1: Bypass CC# Bit 0

Bit 2: Bypass CC# Bit 1

Bit 3: Bypass CC# Bit 2

Bit 4: Bypass CC# Bit 3

Bit 5: Bypass CC# Bit 4

Bit 6: Bypass CC# Bit 5

0xdd Byte 3 (bypass cc# MSB and XY cc# LSB)

Bit 0: Bypass CC# Bit 6

Bit 1: Bypass CC# Bit 7

Bit 2: XY CC# Bit 0

Bit 3: XY CC# Bit 1

Bit 4: XY CC# Bit 2

Bit 5: XY CC# Bit 3

Bit 6: XY CC# Bit 4

0xdd Byte 4 (XY cc# MSB and Block ID LSB)

Bit 0: XY CC# Bit 5

Bit 1: XY CC# Bit 6

Bit 2: XY CC# Bit 7

Bit 3: Block ID Bit 0

Bit 4: Block ID Bit 1

Bit 5: Block ID Bit 2

Bit 6: Block ID Bit 3

0xdd Byte 5 (Block ID MSB) uint32_t MSB

Bit 0: Block ID Bit 4

Bit 1: Block ID Bit 5

Bit 2: Block ID Bit 6

Bit 3: Block ID Bit 7

Bit 4: unused

Bit 5: unused

Bit 6: unused

The following C++ code will iterate thru the sysex message array, take each five-byte chunk and convert them into a uint32_t:

// "data" is the entire sysex array, "lengthOfMessage" is the length/size of that array

for(uint16_t i = 6, n = lengthOfMessage - 1 ; i < n ; i += 5){
  // convert the 5 bytes into a uint32_t with some bit-shifting
  uint32_t blockData = (data[i] & 0x7F) | ((data[i+1] & 0x7F)<<7) | ((data[i+2] & 0x7F)<<14) | ((data[i+3] & 0x7F)<<21) | ((data[i+4] & 0x7F)<<28);

  bool isBlockEngaged = (bool) (blockData & 0x01); // true if the block is on, false if bypassed
  bool isX            = (bool) (blockData & 0x02); // true if the block is in X, false if Y
  uint8_t id          = (uint8_t) ((blockData & 0xFF000000) >> 24);
  uint8_t bypassCC    = (uint8_t) ((blockData & 0x0000FF00) >> 8); // if this number is 0 or higher than 127, then there's no cc# assigned
  uint8_t xyCC        = (uint8_t) ((blockData & 0x00FF0000) >> 16); // if this number is 0 or higher than 127, then there's no cc# assigned
}

GET/SET_BLOCK_PARAMETER_VALUE

This message will get or set the value of the specified block parameter, this value ranges from 0 to 65534, the response message will contain a string which is the label displayed by the Axe Fx II and its editor. For example, the Bass parameter of the AMP block may have a value of 32767 but the label will be "5.00", the value may be 65534 but the label will be "10.00".

Also, many parameters have a low/high limit and step. For example, the "Voices" parameter of the CHORUS block will have a low limit: 2, high limit: 8 and step: 2 that means you can send values of 2,4,6,8. If you send a value lower than 2 it will set the parameter to 2, if it's higher than 8 it will set the value to 8.

The Effect Type selector is also a parameter. For example, in the AMP block the effect type is parameter 0, most blocks with an effect type use parameter 0 as the effect type but not all. You should monitor the MIDI messages between the Axe FX II and Axe-Edit to make sure which parameter is which.

Bypassing/Engaging a Block is also done with this function with parameter 255. Send the value 0 to Engage, 1 to Bypass.

When you are getting a parameter value you still have to include a parameter value with your message but this value can be 0.

To convert these bytes to decimal and vice-versa see MIDI Sysex: converting bytes to decimal and vise versa and more.

Message format:

HEADER BYTES

0x02 Function ID (0x02)

0xdd effect ID bits 6-0

0xdd effect ID bits 13-7

0xdd parameter ID bits 6-0

0xdd parameter ID bits 13-7

0xdd parameter value bits 6-0

0xdd parameter value bits 13-7

0xdd parameter value bits 15-14

0x00 0=query value, 1=set value

0xdd Checksum

0xF7 SysEx End

Response format:

HEADER BYTES

0x02 Function ID (0x02)

0xdd effect ID bits 6-0

0xdd effect ID bits 13-7

0xdd parameter ID bits 6-0

0xdd parameter ID bits 13-7

0xdd parameter value bits 6-0

0xdd parameter value bits 13-7

0xdd parameter value bits 15-14

0xdd

0xdd

0xdd

0xdd

0xdd

0xdd null-terminated string byte0

0xdd byte1

...

0x00 null character

0xdd Checksum

0xF7 SysEx End

SET_TYPED_BLOCK_PARAMETER_VALUE

This is the function used by Axe-Edit when you type the value of a parameter. If you read this page you've learned that parameter values range from 0 to 65534, and, with that in mind, the Bass on the AMP block displays a value of 0.00 to 10.00 with 0.00 being 0 and 10.00 being 65534. If you want to set the value of that parameter to exactly 6.35 then you would use this function.

The parameter value is sent as a 32-bit Signed Float split into five 7-bit bytes, for example, for the Balance parameter on the AMP block you can send -50.6 as the parameter value since the knob displays a range from -100.0 to 100.0.

NOTE: this function behaves differently with the AMP's Level parameter which doesn't seem to respond with the proper value.

Message format:

HEADER BYTES

0x2E Function ID (0x2E)

0xdd Block ID bits 6-0

0xdd Block ID bits 13-7

0xdd Parameter ID bits 6-0

0xdd Parameter ID bits 13-7

0xdd Parameter Value bits 6-0

0xdd Parameter Value bits 13-7

0xdd Parameter Value bits 21-14

0xdd Parameter Value bits 29-22

0xdd Parameter Value bits 32-30

0xdd Checksum

0xF7 SysEx End

This responds in the same way as 0x02 GET/SET_BLOCK_PARAMETER_VALUE.

GET/SET_MODIFIER_VALUE

Message format:

HEADER BYTES

0x07 Function ID (0x07)

0xdd effect ID bits 6-0

0xdd effect ID bits 13-7

0xdd parameter ID bits 6-0

0xdd parameter ID bits 13-7

0xdd modifier parameter selector ID bits 6-0

0xdd 0

0xdd modifier value bits 6-0

0xdd modifier value bits 13-7

0xdd modifier value bits 15-14

0x00 0=query value, 1=set value

0xdd Checksum

0xF7 SysEx End

Response format:

HEADER BYTES

0x02 Function ID (0x02)

0xdd effect ID bits 6-0

0xdd effect ID bits 13-7

0xdd parameter ID bits 6-0

0xdd parameter ID bits 13-7

0xdd modifier parameter selector ID bits 6-0

0xdd 0

0xdd modifier value bits 6-0

0xdd modifier value bits 13-7

0xdd modifier value bits 15-14

0xdd null-terminated string byte0

0xdd byte1

...

0x00 null character

0xdd Checksum

0xF7 SysEx End

Modifier Parameter Selector IDs:

0x0 modifier source

0x1 min

0x2 max

0x3 start

0x4 mid

0x5 end

0x6 slope

0x7 damping

0x8 ?

0x9 ?

0xA auto engage

0xB pc reset

0xC off val

0xD scale

0xE offset

GET_PRESET_NAME

Message format:

HEADER BYTES

0x0F Function ID (0x0F)

0xdd Checksum

0xF7 SysEx End

Response format:

HEADER BYTES

0x0F Function ID (0x0F)

0xdd null-terminated string byte0

0xdd byte1

...

0x00 null character

0xdd Checksum

0xF7 SysEx End

SET_PRESET_NAME

Message format:

HEADER BYTES

0x0F Function ID (0x09)

0xdd Each letter of the preset name sent as an ASCII byte

...

0xdd Checksum

0xF7 SysEx End

This responds with a 0x64 MULTIPURPOSE_RESPONSE.

MIDI_TEMPO_BEAT

This is the Tempo beat or "pulse" message sent by Axe-FX II. Note that the Axe-FX II does not include the Checksum byte in this message:

HEADER BYTES

0x10 Function ID (0x10)

0xF7 SysEx End

SET_TAP_TEMPO

If you want to send a BPM value to the Axe-Fx II/AX8, you can do this via the 0x02 GET/SET_BLOCK_PARAMETER_VALUE function.

To do this, send the parameter to the "CONTROLLERS" Block (ID 141), Parameter ID 32, and the value would be a number between 30 and 250.

GET_PRESET_NUMBER

Message format:

HEADER BYTES

0x14 Function ID (0x14)

0xdd Checksum

0xF7 SysEx End

Response format:

HEADER BYTES

0x14 Function ID (0x14)

0xdd Preset Number bits 6-0

0xdd Preset Number bits 13-7

0xdd Checksum

0xF7 SysEx End

SET_PRESET_NUMBER

This message sets a preset number of your choice, it will respond with message 0x64 to confirm.

Message format:

HEADER BYTES

0x3C Function ID (0x3C)

0xdd Preset Number bits 6-0

0xdd Preset Number bits 13-7

0xdd Checksum

0xF7 SysEx End

This function will respond with 0x64 MULTIPURPOSE_RESPONSE.

GET_GRID_LAYOUT_AND_ROUTING

Message format:

HEADER BYTES

0x20 Function ID (0x20)

0xdd Checksum

0xF7 SysEx End

Response format:

HEADER BYTES

0x20 Function ID (0x20)

Information about each grid location follows. The first 4-byte chunk corresponds to the top-left grid location (column 1, row 1). The next four-byte chunk corresponds to the grid location at column 1, row 2. Following this pattern, each of the 48 grid locations are described.

0xdd Block/Shunt ID bits 6-0

0xdd Block/Shunt ID bits 13-7

0xdd routing flags

Bit 0: connect row 1 to effect input

Bit 1: connect row 2 to effect input

Bit 2: connect row 3 to effect input

Bit 3: connect row 4 to effect input

Bit 4:

Bit 5:

Bit 6:

0xdd (unused?)

... (47 additional four-byte chunks)

0xdd Checksum

0xF7 SysEx End

About Shunts: Each shunt has a unique ID just like blocks, there are 36 shunts, on the Axe-Fx II the Shunt IDs start at 200 up to 235, on the AX8 they start at 300 to 335.

MIDI_LOOPER_STATUS_ENABLE, MIDI_LOOPER_STATUS

Message format:

HEADER BYTES

0x23 Function ID (0x23)

0xdd 0=Disable looper status messages, 1=Enable looper status messages

0xdd Checksum

0xF7 SysEx End

Response format:

HEADER BYTES

0x23 Function ID (0x23)

0xdd Looper Status Bits

Bit 0: Record

Bit 1: Play

Bit 2: Once

Bit 3: Overdub

Bit 4: Reverse

Bit 5: Half

Bit 6: Undo

0xdd Looper Position (range: 0 to 99)

0xdd Checksum

0xF7 SysEx End

GET_SCENE_NUMBER

This is the same as SET_SCENE_NUMBER except you use 0x7F as the value for getting the scene number.

Message format:

HEADER BYTES

0x29 Function ID (0x29)

0x7F Indicator that you want to read the scene number

0xdd Checksum

0xF7 SysEx End

Response format:

HEADER BYTES

0x29 Function ID (0x29)

0xdd Scene Number (range: 0 to 7)

0xdd Checksum

0xF7 SysEx End

SET_SCENE_NUMBER

Message format:

HEADER BYTES

0x29 Function ID (0x29)

0xdd Scene Number (range: 0 to 7)

0xdd Checksum

0xF7 SysEx End

Response format:

HEADER BYTES

0x29 Function ID (0x29)

0xdd Scene Number (range: 0 to 7)

0xdd Checksum

0xF7 SysEx End

GET_CAB_NAME

Message format:

HEADER BYTES

0x12 Function ID (0x12)

0xdd Cab Number

0xdd Checksum

0xF7 SysEx End

Response format:

HEADER BYTES

0x12 Function ID (0x12)

0xdd null-terminated string byte0

0xdd byte1

...

0x00 null character

0xdd Checksum

0xF7 SysEx End

GET_ALL_CAB_NAMES

Message format:

HEADER BYTES

0x12 Function ID (0x12)

0x7F Get all cabs identifier byte 1

0x7F Get all cabs identifier byte 2

0xdd Checksum

0xF7 SysEx End

Response format:

HEADER BYTES

0x12 Function ID (0x12)

0xdd null-terminated string byte0

0xdd byte1

...

0x00 null character

0xdd Checksum

0xF7 SysEx End

MIDI_SET_PRESET

Function number: 14

Example:

F0 0 1 74 3 14 0 1 13 0 FF --> to set the current preset (edit buffer) to preset 0 (1 if DISPLAY OFFSET activated)

F0 0 1 74 3 14 1 0 13 0 FF --> to set the current preset (edit buffer) to preset 128 (129 if DISPLAY OFFSET activated)

Send from AXE-FX to AXE-EDIT and MFC-101

GET_BLOCK_PARAMETERS_LIST

This function will get you a list of all the parameters values of a specified block, each parameter with its value is returned in a separate message.

Message format:

HEADER BYTES

0x01 Function ID (0x01)

0xdd block ID bits 6-0

0xdd block ID bits 13-7

0xdd Checksum

0xF7 SysEx End

This message will respond with 0x32 BATCH_LIST_REQUEST_START confirming that the batch of messages will be sent and how many will be sent.

After that message you will receive messages with function ID 0x01, these messages are identical to function 0x02 with the exception of the function ID being 0x01

Once complete it will respond with 0x33 BATCH_LIST_REQUEST_COMPLETE confirming that they were all sent.

Message 0x01 response format:

HEADER BYTES

0x01 Function ID (0x01)

0xdd block ID bits 6-0

0xdd block ID bits 13-7

0xdd parameter ID bits 6-0

0xdd parameter ID bits 13-7

0xdd parameter value bits 6-0

0xdd parameter value bits 13-7

0xdd parameter value bits 15-14

0xdd

0xdd

0xdd

0xdd

0xdd

0xdd null-terminated string byte0

0xdd byte1

...

0x00 null character

0xdd Checksum

0xF7 SysEx End

BATCH_LIST_REQUEST_START

This message is sent to you when you request a list of certain items, this includes when you request a list of parameters of a block (0x01 GET_BLOCK_PARAMETERS_LIST) or when you request a list of factory/user cab names, you can treat this message as confirmation that those parameters are about to be sent to you. The "Response Length" below represents how many messages will be sent as part of that batch.

Message format:

HEADER BYTES

0x32 Function ID (0x32)

0xdd ID of function that it's replying to

0xdd Response Length bits 6-0

0xdd Response Length bits 13-7

0xdd Checksum

0xF7 SysEx End

BATCH_LIST_REQUEST_COMPLETE

This message is sent to you after a batch of messages you requested was sent to you and is complete.

For example, if you request 0x01 GET_BLOCK_PARAMETERS_LIST, this message will reply confirming that the request has been complete.

The "ID of function that it's replying to" is the ID of the function that requested the list. In the case of 0x01 GET_BLOCK_PARAMETERS_LIST, which is function 0x01, it will show this byte as 0x01 (on the AX8 the function ID will be 0x02 even though the request was for 0x01).

Message format:

HEADER BYTES

0x33 Function ID (0x33)

0xdd ID of function that it's replying to

0xdd Checksum

0xF7 SysEx End

MULTIPURPOSE_RESPONSE

This message is sent by the hardware as a response to certain requests, the first byte after the function id is the requested function id (for example if you change the preset using function id 0x3C the first byte after 0x64 will be 0x3C). The next byte is a response code for the requested function, this code can mean different things, it could mean that the message you first sent had an error, usually if the response code is 0 it means that the task you requested is valid.

Message format:

HEADER BYTES

0x64 Function ID (0x64)

0xdd Response Function ID

0xdd Response Code

0xdd Checksum

0xF7 SysEx End

GET_BLOCK_XY, SET_BLOCK_XY

Message format:

HEADER BYTES

0x11 Function ID (0x11)

0xdd effect ID bits 6-0

0xdd effect ID bits 13-7

0xdd 0 = set to X, 1 = set to Y

0xdd 0 = get value, 1 = set value

0xdd Checksum

0xF7 SysEx End

Response format:

HEADER BYTES

0x11 Function ID (0x11)

0xdd effect ID bits 6-0

0xdd effect ID bits 13-7

0xdd 0 = effect is X, 1 = effect is Y

0xdd Checksum

0xF7 SysEx End

SET_BLOCK_BYPASS_STATE

You can Bypass/Engage a block using Function 0x02 GET/SET_BLOCK_PARAMETER_VALUE. To do this you will use the Block ID that you want to bypass, Parameter ID 255, and the value would be 0 to Engage and 1 to Bypass.

For example, this will bypass the amp block. Keep in mind the checksum must be calculated for the target device:

HEADER BYTES

0x02 Function ID (2)

0x6A effect ID bits 6-0

0x00 effect ID bits 13-7

0x7F parameter ID bits 6-0

0x01 parameter ID bits 13-7

0x01 parameter value bits 6-0

0x00 parameter value bits 13-7

0x00 parameter value bits 15-14

0x01 Set Value

0xXX Checksum

0xF7 SysEx End

GET_CPU_USAGE

Message format:

HEADER BYTES

0x13 Function ID (0x13)

0xdd Checksum

0xF7 SysEx End

Response format:

HEADER BYTES

0x13 Function ID (0x13)

0xdd CPU % (single byte from 0 to 100)

0xdd Checksum

0xF7 SysEx End

GET_PRESET_EDITED_STATUS

The Axe FX and AX8 both have an LED on the front panel labeled "EDITED", which lights whenever you make any changes to your preset that have not been saved. This message will request that status. It will reply with 1 if the LED is on because the preset has changes that need to be saved, and 0 if it's off.

Message format:

HEADER BYTES

0x2A Function ID (0x2A)

0xdd Checksum

0xF7 SysEx End

Response format:

HEADER BYTES

0x2A Function ID (0x2A)

0xdd 0 = NO, 1 = YES

0xdd Checksum

0xF7 SysEx End

SET_TARGET_BLOCK

This function is sent when Axe-Edit opens a block for editing, this message should be sent if you will be requesting Real Time modifiers or the GET_MONITOR_GRAPH.

Message format:

HEADER BYTES

0x37 Function ID (0x37)

0xdd Block ID bits 6-0

0xdd Block ID bits 13-7

0xdd Checksum

0xF7 SysEx End

Responds with 0x64 MULTIPURPOSE_RESPONSE

GET_MONITOR_GRAPH

This function responds with the Monitor Graph, this is the "MONITOR" section you see on Axe-Edit displaying the EQ curve of many blocks.

This function's response contains 256 bytes, aside from the header, checksum and sysex end bytes, representing 128 points on the graph, where each point is made up of two bytes.

Each pair of bytes is a 14-bit signed integer, the integer will range from -8191 to 8191 with 0 being the middle of the graph. The Controllers tab also makes use of this graph for ADSR1/2 but the integer will range from 0 to 8191.

When requesting this Graph you must specify the Index of the graph. All blocks have one graph, so use 0 as the Graph Index, with the exception of the Controllers which has two graphs, ADSR1 Index is 0, ADSR2 Index is 1.

You MUST send SET_TARGET_BLOCK before requesting the graph since the graph request does not include a block id.

TIP: you should be careful with how often you request this graph. You should only do it when after a set interval after the parameter for that block has been edited.

Message format:

HEADER BYTES

0x36 Function ID (0x36)

0xdd Graph Index (0 for most blocks, see the above info)

0xdd Checksum

0xF7 SysEx End

HEADER BYTES

0x36 Function ID (0x36)

256 bytes to follow, representing 128 14-bit Signed Integers

0xdd Point 1 bits 6-0

0xdd Point 1 bits 13-7

0xdd Point 2 bits 6-0

0xdd Point 2 bits 13-7

0xdd Point 3 bits 6-0

0xdd Point 3 bits 13-7

...

0xdd Checksum

0xF7 SysEx End

GET/SET_AX8_FOOTSWITCHES

This function returns the contents of both the per-preset and global foot-switches on the AX8.

It includes eight 6-byte chunks:

• The first 2 bytes of the chunk represent the block of the local (per-preset) footswitch, the ID will be the Block ID or other IDs representing the function of the footswitch.
• The next two bytes of the chunk represent the global footswitch block ID.
• The next byte represents the flags of the global footswitch, as in if the global footswitch is engaged, engaged+momentary & engaged+latching.
• The next byte represents the flags of the local footswitch.
• When the Global Flag is 0 the per-preset footswitch is used. When the flag is 1, global is engaged in as a latching type. When it is 2 it's engaged as a momentary type.

Message format:

HEADER BYTES

0x48 Function ID (0x48)

0xdd QUERY, 0=Get Value, 1=Set Value

0xdd Number of Foot-switches (0 to request all)

0xdd Checksum

0xF7 SysEx End

Response format:

HEADER BYTES

0x48 Function ID (0x48)

0xdd QUERY, 0=Get Value, 1=Set Value

0xdd Number of Foot-switches (0x08 on the AX8)

Eight 6-byte chunks to follow (with the first chunk representing footswitch 1, last one footswitch 8)

0xdd Local ID bits 6-0

0xdd Local ID bits 13-7

0xdd Global ID bits 6-0

0xdd Global ID bits 13-7

0xdd Global Flag, 0=Global Disabled, 1=Global Engaged/Latching, 2=Global Engaged/Momentary

0xdd Local Flag, 1=Local Latching, 2=Local Momentary

...

0xdd Checksum

0xF7 SysEx End

To edit footswitches you send the entire layout of footswitches with the QUERY being 1, you would include each 6-byte chunk after the Number of Foot-switches, each chunk would have to have the values you want to set for each footswitch.

MIDI SysEx: calculating the SysEx Checksum

As mentioned above, the Axe-FX II units require a Checksum at the end of the SysEx string that is sent to it (before the terminating F7 byte) as a verification step.

In order to calculate the Checksum, you basically have to XOR every byte from the start of the SysEx message, up to the character BEFORE the terminating F7 byte. For example, to send the following SysEx message (to fetch a preset name):

F0 00 01 74 03 0F F7

We would have to XOR all the byte values from the starting 'F0' to the '0F' which is the second last byte:

0xF0 ^ 0x00 ^ 0x01 ^ 0x74 ^ 0x03 ^ 0x0F = 0x89

Then, we would need to strip the leftmost bit from the result (by ANDing it to 0x7F):

0x89 & 0x7F = 0x09

And, we add this byte (actually, a septet now) to the end of the SysEx string, BEFORE the terminating F7:

F0 00 01 74 03 0F 09 F7

Obviously, in a "static" SysEx message like above, you do not have to recalculate the Checksum each time as it will always be "09" as the rest of the message does not change, but if you are sending a SysEx string to change a parameter value, etc., then you will have to calculate the Checksum on the fly as byte values towards the end of the SysEx string will be different each time.

For Python users, here is a checksum function to return the checksum string:

from functools import reduce

def checksum(ip_str):
    outstr =   # Create an outstring object
    ip_list = ip_str.split()  # Split the string into a list
    int_list = [int('0x' + str(x), 16) for x in ip_list[0:-1]]  #  Create an integer list
    s = reduce(lambda x, y: x ^ y, int_list)  # Calculate the checksum
    int_list.append(s & 0x7f)  # Append the checksum to the list with leftmost bit stripped
    int_list.append(0xF7)  # Append the terminating byte to the list
    for itm in int_list:  # Get each item from the list
        a_str = str(hex(itm))[2:]  # Create a string without the first two characters
        outstr = outstr + a_str.zfill(2) + ' '  # Concatenate each item into a single string
    return outstr.strip()  # Strip leading or trailing blanks and return the string

MIDI SysEx: obtaining parameter values

The old Standard/Ultra devices used to store the parameter values on *most* knobs as 0-254. This was split into two bytes, XX YY where XX was the lowest 4 bits of the value, and YY was the highest 4 bits. Pretty simple.

The new Axe-II now has more granular control over *most* knobs, with the values going from 0-65534. This requires a full 16 bits to store. The problem is that the MIDI specifications means you can only transmit values using 7 bits as the highest bit of each byte must be a zero.

To get around this, the Axe-II uses THREE bytes to transmit the values XX YY ZZ where XX is the lowest 7 bits of the data, YY is the 8th to the 14th bit of the data, and ZZ is the remaining top two bits of the data.

So, if you had the value 52421 on a knob, then this would be represented by the 16 bits: 1100110011000101.

If you split this into segments of length 2/7/7 to store in ZZ/YY/XX: 11 0011001 1000101

So XX gets the last segment: 01000101 And YY gets the middle segment: 00011001 And ZZ gets the first segment: 00000011

You will also have to back-calculate the respective knob values to the 16 bit values. For example, a knob that goes from 0 - 10, 0 would of course be 0, but 10 would be 65534. From there, you would work out that 5 is 32767 and 7 would be about 45871 etc.

To convert these bytes to the decimal value and visa-versa read MIDI Sysex: converting bytes to decimal and vise versa and more.

MIDI SysEx: loading IRs

The information below was provided by former forum member LMO.

The Axe Fx II supports 2040-point impulse responses that are packaged for download in a series of 66 MIDI SysEx messages, as follows:

MIDI_START_IR_DOWNLOAD

Prepare the Axe-Fx II to receive impulse response data

Message Format:

HEADER BYTES

0x7A function ID

0x20

0x00

0x10

0xdd Checksum

0xF7 SysEx End

MIDI_G2_IR_DATA

There are 64 SysEx messages, each containing 32 chunks of data. Each chunk consists of five bytes and can hold either four text characters or one 32-bit IR data sample.

The first data message sent includes 8 chunks of text that specify the 32-character IR name, and 24 chunks of IR data. The subsequent 63 data messages each contain 32 data samples for a total of 2040 samples.

Message Format:

HEADER BYTES

0x7B function ID

0x20

0x00

0xdd data chunk byte 0

0xdd data chunk byte 1

0xdd data chunk byte 2

0xdd data chunk byte 3

0xdd data chunk byte 4

--- 31 additional five byte data chunks ---

0xdd Checksum

0xF7 SysEx End

MIDI_CLOSE_IR_DOWNLOAD

Terminate the IR download sequence

Message Format:

HEADER BYTES

0x7C function ID

0xdd encoded Checksum byte 0 for IR data

0xdd encoded Checksum byte 1 for IR data

0xdd encoded Checksum byte 2 for IR data

0xdd encoded Checksum byte 3 for IR data

0xdd encoded Checksum byte 4 for IR data

0xdd Checksum

0xF7 SysEx End

Data Chunk Encoding Scheme

The data encoding scheme translates four octets into five septets. Each septet occupies the lower seven bits of a byte, with the most significant bit set to 0.

• octet is one byte containing 8 bits of data
• septet is one byte containing 7 bits of data

byte_chunk = (data[0] & 0xFF )<< 24 | (data[1] & 0xFF )<< 16 | (data[2] & 0xFF )<< 8 (data[3] & 0xFF;

• convert four octets to five septets

septet[0] = byte_chunk & 0xFF;

septet[1] = byte_chunk >> 7 & 0xFF;

septet[2] = byte_chunk >> 14 & 0xFF;

septet[3] = byte_chunk >> 21 & 0xFF;

septet[4] = byte_chunk >> 28 & 0xFF;

MIDI Sysex: converting bytes to decimal and vise versa and more

All the functions below are written in C++.

The following are for each 5 byte chunk of message 0x0E [#PRESET_BLOCKS_DATA|PRESET_BLOCKS_DATA].

This function returns true if the block is in X state or false if the block is in Y state. x is the first byte of each 5 byte chunk of message 0x0E.

bool isBlockX(byte x){
  if(x==0x03||x==0x02){
    return true;
  }
  return false;
}

This function returns true if the block is bypassed, false if it's not. x is the first byte of each 5 byte chunk of message 0x0E.

bool isBlockBypassed(byte x){
  if(x==0x03||x==0x01){
    return false;
  }
  return true;
}

This function converts the two bytes for the block's bypass CC (IA CC Number LSB/MSB) into a decimal number. LSB is the second byte and MSB is the third byte of each 5 byte chunk of message 0x0E.

int toBlockCC(byte LSB, byte MSB){
  return ((LSB & 0x7E) >> 1) + ((MSB & 3) << 6);
}

This function converts the two bytes for the block's ID (Effect ID LSB/MSB) into a decimal number. LSB is the fourth byte and MSB is the fifth byte of each 5 byte chunk of message 0x0E.

int blockID(byte LSB, byte MSB){
  return ((LSB & 0x78) >> 3) + ((MSB & 0x0F) << 4);
}

This function converts the effect ID bytes OR the parameter ID bytes into a decimal number.

int bytesToInt(byte byte1, byte byte2){
  return (byte1 & 0x7F) | ((byte2 & 0x7F)<<7);
}

This is the reverse of the above to turn a decimal number into two bytes where x is the decimal number.

byte byte1 = (x & 0x7F);

byte byte2 = ((x >> 7) & 0x7F);

This function converts the 3 parameter value bytes on message (0x02) into a decimal number.

int parameterValueBytesToInt(byte byte1, byte byte2, byte byte3){
  return (byte1 & 0x7F) | ((byte2 & 0x7F)<<7) | ((byte3 & 0x7F)<<14);
}

This is the reverse of the above to turn a decimal number into 3 bytes where x is the decimal number.

byte byte1 = x & 0x7F;

byte byte2 = (x >> 7) & 0x7F;

byte byte3 = (x >> 14) & 0x7F);

This will convert a decimal number into the two bytes for a preset change, where x is the decimal number.

byte byte1 = x >> 7;

byte byte2 = x & 0x7F;

To convert the two bytes received from a preset change to a decimal number use:

Axe FX II:

int x = (byte1 & 0x7F) << 7 | byte2;

AX8:

int x = (byte1 & 0x7F) | ((byte2 & 0x7F) << 7);

This will convert the decimal preset number into a Bank/Preset set. This number ranges from 0 to 383 on the Axe FX II, 0 to 767 on the XL/+ and 0 to 511 on the AX8.

On the Axe FX II or later, where x is the decimal number from 0 to 383/767:

byte bankNumber = floor(x / 128); // banks are labeled A,B,C,D,E,F where bank A is 0 and bank F is 5

byte presetNumber = x - (bankNumber*128); // preset number with index of 0, to display offset it to 1 just add 1 to this number when displayed

For the AX8, where x is the decimal number from 0 to 511:

byte bankNumber = floor(x / 8); // banks are labeled from 1 to 64, this functions will return a number from 0 to 63, add 1 when you display it

byte presetNumber = x - (bank * 8);

MIDI SysEx: Blocks & Parameters IDs

Read this: MIDI SysEx

MIDI SysEx: more information

Read this: Recalling presets and scenes in hex

Axe-Fx II MIDI SysEx: Info

The following tables contain Axe-Fx II data as of Quantum 8.02.

Information on this page is for educational purposes only.

Axe-Fx II MIDI SysEx: Block IDs

ID	Name	Group Code	Can Bypass	Available on AX8	Axe-Fx II X/Y	Axe-Fx II XL/XL+ X/Y	AX8 X/Y
106	Amp 1	AMP	Yes	Yes	Yes	Yes	Yes
107	Amp 2	AMP	Yes	No	Yes	Yes	Yes
108	Cab 1	CAB	Yes	Yes	Yes	Yes	Yes
109	Cab 2	CAB	Yes	No	Yes	Yes	Yes
116	Chorus 1	CHO	Yes	Yes	Yes	Yes	Yes
117	Chorus 2	CHO	Yes	No	Yes	Yes	Yes
100	Compressor 1	CPR	Yes	Yes	No	Yes	Yes
101	Compressor 2	CPR	Yes	No	No	Yes	Yes
141	Controllers	CONTROLLERS	No	Yes	No	No	No
148	Crossover 1	XVR	Yes	No	No	No	No
149	Crossover 2	XVR	Yes	No	No	No	No
112	Delay 1	DLY	Yes	Yes	Yes	Yes	Yes
113	Delay 2	DLY	Yes	Yes	Yes	Yes	Yes
133	Drive 1	DRV	Yes	Yes	Yes	Yes	Yes
134	Drive 2	DRV	Yes	Yes	Yes	Yes	Yes
135	Enhancer	ENH	Yes	Yes	No	No	No
136	FX Loop	FXL	Yes	Yes	No	No	No
143	Feedback Return	RTN	No	No	No	No	No
142	Feedback Send	SND	No	No	No	No	No
131	Filter 1	FIL	Yes	Yes	No	No	Yes
132	Filter 2	FIL	Yes	Yes	No	No	Yes
164	Filter 3	FIL	Yes	No	No	No	Yes
165	Filter 4	FIL	Yes	No	No	No	Yes
118	Flanger 1	FLG	Yes	Yes	Yes	Yes	Yes
119	Flanger 2	FLG	Yes	No	Yes	Yes	Yes
126	Formant	FRM	Yes	Yes	No	No	No
150	Gate Expander	GTE	Yes	Yes	No	Yes	Yes
151	Gate Expander 2	GTE	Yes	No	No	Yes	Yes
102	Graphic EQ 1	GEQ	Yes	Yes	No	Yes	No
103	Graphic EQ 2	GEQ	Yes	Yes	No	Yes	No
160	Graphic EQ 3	GEQ	Yes	No	No	Yes	No
161	Graphic EQ 4	GEQ	Yes	No	No	Yes	No
139	Input Noise Gate	INPUT	No	Yes	No	No	No
169	Looper	LPR	Yes	Yes	No	No	No
147	Megatap Delay	MGT	Yes	No	No	No	No
137	Mixer	MIX	No	No	No	No	No
138	Mixer 2	MIX	No	No	No	Yes	No
114	Multi Delay 1	MTD	Yes	Yes	Yes	Yes	Yes
115	Multi Delay 2	MTD	Yes	No	Yes	Yes	Yes
154	Multiband Compressor 1	MBC	Yes	No	No	No	No
155	Multiband Compressor 2	MBC	Yes	No	No	No	No
140	Output	OUTPUT	No	Yes	No	No	No
104	Parametric EQ 1	PEQ	Yes	Yes	No	Yes	No
105	Parametric EQ 2	PEQ	Yes	Yes	No	Yes	No
162	Parametric EQ 3	PEQ	Yes	No	No	Yes	No
163	Parametric EQ 4	PEQ	Yes	No	No	Yes	No
122	Phaser 1	PHA	Yes	Yes	Yes	Yes	Yes
123	Phaser 2	PHA	Yes	No	Yes	Yes	Yes
130	Pitch 1	PIT	Yes	Yes	Yes	Yes	Yes
153	Pitch 2	PIT	Yes	No	Yes	Yes	Yes
156	Quad Chorus 1	QCH	Yes	No	No	No	No
157	Quad Chorus 2	QCH	Yes	No	No	No	No
158	Resonator 1	RES	Yes	No	No	No	No
159	Resonator 2	RES	Yes	No	No	No	No
110	Reverb 1	REV	Yes	Yes	Yes	Yes	Yes
111	Reverb 2	REV	Yes	No	Yes	Yes	Yes
152	Ring Modulator	RNG	Yes	Yes	No	No	No
120	Rotary Speaker 1	ROT	Yes	Yes	Yes	Yes	Yes
121	Rotary Speaker 2	ROT	Yes	No	Yes	Yes	Yes
144	Synth 1	SYN	Yes	Yes	No	No	No
145	Synth 2	SYN	Yes	No	No	No	No
170	Tone Match	TMA	Yes	No	No	No	No
128	Tremolo/Panner 1	TRM	Yes	Yes	No	Yes	Yes
129	Tremolo/Panner 2	TRM	Yes	No	No	Yes	Yes
146	Vocoder	VOC	Yes	No	No	No	No
127	Volume/Pan 1	VOL	Yes	Yes	No	No	No
166	Volume/Pan 2	VOL	Yes	Yes	No	No	No
167	Volume/Pan 3	VOL	Yes	No	No	No	No
168	Volume/Pan 4	VOL	Yes	No	No	No	No
124	Wah 1	WAH	Yes	Yes	Yes	Yes	Yes
125	Wah 2	WAH	Yes	No	Yes	Yes	Yes

Back to Top

Axe-Fx II MIDI SysEx

CPR

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
CPR	0	TRESHOLD	knob					No
CPR	1	RATIO	knob					No
CPR	2	ATTACK	knob					No
CPR	3	RELEASE	knob					No
CPR	4	Level	knob					Yes
CPR	5	KNEE	select	0: HARD 1: SOFT 2: SOFTER 3: SOFTEST				No
CPR	6	MAKEUP	switch		0: Off	1: On		No
CPR	7	DETECT	select	0: RMS 1: PEAK 2: RMS+PEAK 3: FAST RMS				No
CPR	8	FILTER	knob					No
CPR	10	SIDECHAIN	select	0: BLOCK L+R 1: ROW 1 2: ROW 2 3: ROW 3 4: ROW 4 5: INPUT 1 6: INPUT 2 7: BLOCK L 8: BLOCK R				No
CPR	11	MIX	knob					Yes
CPR	12	EFFECT TYPE	select	0: STUDIO COMP 1: PEDAL COMP 1 2: PEDAL COMP 2 3: DYNAMICS 4: OPTICAL 1 5: OPTICAL 2				No
CPR	13	COMP	knob					No
CPR	14	BYPASS MODE	select	0: THRU 1: MUTE FX OUT 2: MUTE OUT				Yes
CPR	15	LOOK AHEAD	knob					No
CPR	16	AUTO	switch		0: Off	1: On		No
CPR	17	EMPHASIS	knob					No
CPR	18	DYNAMICS	knob					No
CPR	19	INPUT Level	select	0: INSTRUMENT 1: LINE				No	Since Quantum 7.01

Back to Top

GEQ

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
GEQ	0	31	slider					No
GEQ	1	63	slider					No
GEQ	2	125	slider					No
GEQ	3	250	slider					No
GEQ	4	500	slider					No
GEQ	5	1K	slider					No
GEQ	6	2K	slider					No
GEQ	7	4K	slider					No
GEQ	8	8K	slider					No
GEQ	9	16K	slider					No
GEQ	11	Level	knob					Yes
GEQ	12	Balance	knob					Yes
GEQ	13	BYPASS MODE	select	0: THRU 1: MUTE				Yes
GEQ	15	EFFECT TYPE	select	0: 10 BAND CONST Q 1: 8 BAND CONST Q 2: 7 BAND CONST Q 3: 5 BAND CONST Q 4: 10 BAND VAR Q 5: 8 BAND VAR Q 6: 7 BAND VAR Q 7: 5 BAND VAR Q 8: 5 BAND PASSIVE 9: 4 BAND PASSIVE 10: 3 BAND PASSIVE 11: 3 BAND CONSOLE				No
GEQ	16	MASTER Q	knob					No

Back to Top

PEQ

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
PEQ	0	FREQ 1	knob					No
PEQ	1	FREQ 2	knob					No
PEQ	2	FREQ 3	knob					No
PEQ	3	FREQ 4	knob					No
PEQ	4	FREQ 5	knob					No
PEQ	5	Q 1	knob					No
PEQ	6	Q 2	knob					No
PEQ	7	Q 3	knob					No
PEQ	8	Q 4	knob					No
PEQ	9	Q 5	knob					No
PEQ	10	GAIN 1	knob					No
PEQ	11	GAIN 2	knob					No
PEQ	12	GAIN 3	knob					No
PEQ	13	GAIN 4	knob					No
PEQ	14	GAIN 5	knob					No
PEQ	15	FREQ TYPE 1	select	0: SHELVING 1: PEAKING 2: BLOCKING 3: SHELVING2				No
PEQ	16	FREQ TYPE 5	select	0: SHELVING 1: PEAKING 2: BLOCKING 3: SHELVING2				No
PEQ	17	FREQ TYPE 2	select	0: PEAKING 1: SHELVING 2: SHELVING2				No
PEQ	18	FREQ TYPE 4	select	0: PEAKING 1: SHELVING 2: SHELVING2				No
PEQ	19	Level	knob					Yes
PEQ	20	Balance	knob					Yes
PEQ	21	BYPASS MODE	select	0: THRU 1: MUTE				Yes

Back to Top

AMP

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
AMP	0	EFFECT TYPE	select	0: 59 BASSGUY 1: 65 BASSGUY NRML 2: VIBRATO VERB 3: DELUXE VERB VIB 4: DOUBLE VERB VIB 5: JR BLUES 6: CLASS-A 15W TB 7: CLASS-A 30W 8: CLASS-A 30W TB 9: BRIT JM45 10: PLEXI 50W NRML 11: PLEXI 50W HI 1 12: 1987X NORMAL 13: 1987X TREBLE 14: BRIT 800 15: BRIT SUPER 16: HIPOWER NORMAL 17: HIPOWER BRILLNT 18: USA CLEAN 19: USA PRE CLEAN 20: USA RHYTHM 21: USA IIC+ 22: USA IIC+ BRight 23: USA LEAD 24: USA LEAD BRT 25: RECTO2 ORG VNTG 26: RECTO2 ORG MDRN 27: RECTO2 RED VNTG 28: RECTO2 RED MDRN 29: EURO BLUE 30: EURO RED 31: SHIVER CLEAN 32: SHIVER LEAD 33: EURO UBER 34: SOLO 99 CLEAN 35: SOLO 100 RHY 36: SOLO 100 LEAD 37: FRIEDMAN BE V1 38: FRIEDMAN HBE V1 39: PVH 6160 BLOCK 40: MR Z MZ-38 41: CA3+ RHY 42: CA3+ LEAD 43: WRECKER ROCKET 44: CORNCOB M50 45: CA OD-2 46: FRYETTE D60 L 47: FRYETTE D60 M 48: BRIT BROWN 49: CITRUS RV50 50: JAZZ 120 51: ENERGYBALL 52: ODS-100 CLEAN 53: ODS-100 HRM 54: FAS RHYTHM 55: FAS LEAD 1 56: FAS LEAD 2 57: FAS MODERN 58: DAS METALL 59: BRIT PRE 60: BUTTERY 61: BOUTIQUE 1 62: BOUTIQUE 2 63: CAMERON CCV 1A 64: CAMERON CCV 2A 65: SV BASS 66: TUBE PRE 67: FAS BROWN 68: BIG HAIR 69: SOLO 99 LEAD 70: SUPERTWEED 71: TX STAR LEAD 72: FAS WRECK 73: BRIT JVM OD1 OR 74: BRIT JVM OD2 OR 75: FAS 6160 76: CALI LEGGY 77: USA LEAD + 78: USA LEAD BRT + 79: PRINCE TONE 80: BLANKNSHP LEEDS 81: 5153 100W GREEN 82: 5153 100W BLUE 83: 5153 100W RED 84: SOLO 88 RHYTHM 85: DIV/13 CJ 86: HERBIE CH2- 87: HERBIE CH2+ 88: HERBIE CH3 89: DIRTY SHIRLEY 1 90: DIZZY V4 BLUE 2 91: DIZZY V4 BLUE 3 92: DIZZY V4 BLUE 4 93: SUHR BADGER 18 94: SUHR BADGER 30 95: PRINCE TONE NR 96: SUPREMO TREM 97: ATOMICA LOW 98: ATOMICA HIGH 99: DELUXE TWEED 100: SPAWN ROD OD2-1 101: SPAWN ROD OD2-2 102: SPAWN ROD OD2-3 103: BRIT SILVER 104: SPAWN NITROUS 2 105: FAS CRUNCH 106: TWO STONE J35 1 107: FOX ODS 108: HOT KITTY 109: BAND-COMMANDER 110: SUPER VERB VIB 111: VIBRA-KING 112: GIBTONE SCOUT 113: PVH 6160+ LD 114: SOLO 100 CLEAN 115: USA PRE LD2 GRN 116: USA PRE LD2 YLW 117: CA3+ CLEAN 118: FOX ODS DEEP 119: BRIT JVM OD1 GN 120: BRIT JVM OD2 GN 121: VIBRATO LUX 122: BRIT 800 MOD 123: NUCLEAR-TONE 124: BLUDOJAI CLEAN 125: BLUDOJAI LD PAB 126: PLEXI 100W HIGH 127: PLEXI 100W NRML 128: RUBY ROCKET 129: AC-20 EF86 B 130: PRINCE TONE REV 131: COMET CONCOURSE 132: FAS MODERN II 133: CA TRIPTIK MDRN 134: CA TRIPTIK CLSC 135: CA TRIPTIK CLN 136: THORDENDAL VINT 137: THORDENDAL MDRN 138: ODS-100 HRM MID 139: EURO BLUE MDRN 140: EURO RED MDRN 141: PLEXI 50W JUMP 142: AC-20 EF86 T 143: COMET 60 144: HIPOWER JUMPED 145: PLEXI 100W JUMP 146: BRIT JM45 JUMP 147: 1987X JUMP 148: RECTO1 ORG VNTG 149: RECTO1 RED 150: ODS-100 FORD 1 151: BOGFISH STRATO 152: BOGFISH BROWN 153: 5F1 TWEED 154: WRECKER EXPRESS 155: TWO STONE J35 2 156: ODS-100 FORD 2 157: MR Z MZ-8 158: CAR ROAMER 159: USA SUB BLUES 160: WRECKER LVRPOOL 161: CITRUS TERRIER 162: CITRUS A30 CLN 163: CITRUS A30 DRTY 164: DIV/13 FT37 LO 165: DIV/13 FT37 HI 166: MATCHBOX D-30 167: FAS CLASS-A 168: USA BASS 400 1 169: USA BASS 400 2 170: CITRUS BASS 200 171: FAS BASS 172: TREMOLO LUX 173: FAS BROOTALZ 174: RECTO1 ORG MDRN 175: ANGLE SEVERE 1 176: ANGLE SEVERE 2 177: USA PRE LD2 RED 178: USA PRE LD1 RED 179: TX STAR CLEAN 180: AC-20 12AX7 T 181: VIBRATO VERB AA 182: VIBRATO VERB AB 183: CA TUCANA LEAD 184: JR BLUES FAT 185: SOLO 88 LEAD 186: BRIT AFS100 1 187: BRIT AFS100 2 188: CLASS-A 30W HOT 189: DIZZY V4 SLVR 2 190: DIZZY V4 SLVR 3 191: DIZZY V4 SLVR 4 192: 1959SLP NORMAL 193: 1959SLP TREBLE 194: 1959SLP JUMP 195: FAS MODERN III 196: ODS-100 FORD MD 197: MR Z HWY 66 198: 6G4 SUPER 199: 6G12 CONCERT 200: 65 BASSGUY BASS 201: VIBRA-KING FAT 202: SPAWN ROD OD1-1 203: SPAWN ROD OD1-2 204: SPAWN ROD OD1-3 205: CA TUCANA CLN 206: BRIT JVM OD1 RD 207: BRIT JVM OD2 RD 208: CAMERON CCV 1B 209: CAMERON CCV 2B 210: CAMERON CCV 2C 211: CAMERON CCV 2D 212: FRIEDMAN SM BOX 213: 5153 50W BLUE 214: DIV/13 CJ BOOST 215: USA IIC+ DEEP 216: USA IIC+ BRT/DP 217: 5F8 TWEED 218: DOUBLE VERB SF 219: VIBRATO VERB CS 220: JMPRE-1 OD1 221: JMPRE-1 OD2 222: JMPRE-1 OD1 BS 223: JMPRE-1 OD2 BS 224: DELUXE VERB NRM 225: DOUBLE VERB NRM 226: SUPER VERB NRM 227: BLUDOJAI LD 2 228: PLEXI 50W 6550 229: FAS HOT ROD 230: PVH 6160+ RHY B 231: PVH 6160+ RHY 232: SOLO 88 CLEAN 233: CLASS-A 30W BRT 234: PLEXI 50W HI 2 235: SPAWN NITROUS 1 236: RUBY ROCKET BRT 237: AC-20 12AX7 B 238: PLEXI 100W 1970 239: JS410 LEAD OR 240: JS410 LEAD RD 241: JS410 CRUNCH OR 242: JS410 CRUNCH RD 243: FRIEDMAN BE V2 244: FRIEDMAN HBE V2 245: DWEEZIL'S B-MAN 246: FRIEDMAN BE 247: FRIEDMAN HBE 248: USA IIC++ 249: LEGATO 100 250: CAPT HOOK 2B 251: CAPT HOOK 3B 252: CAPT HOOK 2A 253: CAPT HOOK 3A 254: CAPT HOOK 1A 255: CAPT HOOK 1B 256: DIRTY SHIRLEY 2 257: BRIT 800 #34 258: 5F1 TWEED EC				No
AMP	1	INPUT DRIVE	knob					Yes
AMP	2	BASS	knob					No
AMP	3	MIDDLE	knob					No
AMP	4	TREBLE	knob					No
AMP	5	MASTER VOLUME	knob					Yes
AMP	6	PREAMP LOW CUT	knob					No
AMP	7	HIGH CUT FREQ	knob					No
AMP	8	TONE FREQ	knob					No
AMP	9	XFORMER GRIND	knob					No
AMP	10	BRight CAP	knob					No
AMP	12	XFORMER LOW FREQ	knob					No
AMP	13	XFORMER HI FREQ	knob					No
AMP	14	TONE LOCATION	select	0: PRE 1: POST 2: MID 3: END				No
AMP	15	INPUT SELECT	select	0: Left 1: Right 2: SUM L+R				No
AMP	16	DEPTH	knob					No
AMP	19	SUPPLY SAG	knob					No
AMP	20	PRESENCE	knob					No
AMP	21	Level	knob					No
AMP	22	Balance	knob					Yes
AMP	23	BYPASS MODE	select	0: Left 1: Right 2: SUM L+R				Yes
AMP	24	NEG FEEDBACK	knob					No
AMP	25	PRESENCE FREQ	knob					No
AMP	26	LOW RES FREQ	knob					No
AMP	27	LOW RES	knob					No
AMP	29	DEPTH FREQ	knob					No
AMP	31	MV CAP	knob					No
AMP	33	HARMONICS	knob					No
AMP	34	TONE STACK	select	0: ACTIVE 1: DEFAULT 2: BROWNFACE 3: BLACKFACE 4: BASSGUY 5: TOP BOOST 6: PLEXI 7: BOUTIQUE 8: HI POWER 9: USA NORMAL 10: USA FAT 11: RECTO1 ORG 12: RECTO1 RED 13: SKYLINE 14: GERMAN 15: JR BLUES 16: WRECKER 1 17: NEUTRAL 18: CA3+SE 19: FREYER D60 20: MR Z 38 SR 21: EURO UBER 22: PVH 6160 23: SOLO 100 24: CORNCOB 25: XTC 26: CAROLANN 27: CITRUS 28: BRIT JM45 29: USA RHY 30: RECTO2 ORG 31: RECTO2 RED 32: SHIVER CLN 33: CAMERON 34: BRIT JVM 0D1 35: BRIT JVM 0D2 36: 5153 GREEN 37: 5153 BLUE 38: 5153 RED 39: BRIT SUPER 40: DIV13 CJ 41: BADGER 18 42: ATOMICA 43: SPAWN 44: BADGER 30 45: BRIT SILVER 46: SUPER VERB 47: HOT KITTY 48: VIBRATO-KING 49: GIBTONE SCOUT 50: CA3+SE CLEAN 51: BF FIXED MID 52: GERMAN V4 53: VIBRATO-LUX 54: DIRTY SHIRLEY 55: PLEXI 100W 56: RUBY ROCKET BRT 57: CONCOURSE 58: TRIPTIK LD 59: TRIPTIK CLN 60: JAZZ 120 61: BOGFISH 62: WRECKER 2 63: SKYLINE DEEP 64: USA SUB BLUES 65: WRECKER LVRPOOL 66: CITRUS A30 CLN 67: CITRUS A30 DRT 68: CAR ROAMER 69: USA BASS 70: CITRUS BASS 71: STUDIO 72: BRIT 800 73: RECTO1 ORG MDRN 74: ANGLE SEVERE 1 75: ANGLE SEVERE 2 76: USA PRE LD1 RED 77: RECTO ORG BRT 78: RECTO RED BRT 79: VIBROVERB AA 80: PVH 6160 II LD 81: RUMBLE HRM 82: MR Z HWY 66 83: SUPER 6G4 84: 65 BASSMAN BASS 85: FREIDMAN 86: BAND-COMMANDER 87: USA PRE CLEAN 88: TUCANA CLEAN 89: FRIEDMAN SM BOX 90: TX STAR 91: USA IIC+ 92: THORDENDAL 93: SOLO 99 94: BLUDOJAI 95: HERBIE 96: PVH 6160 II RHY 97: SOLO 88 CLEAN 98: JS410 99: JS410 MIDSHIFT 100: RUBY ROCKET 101: USA IIC++ 102: LEGATO 100 103: HOOK EDGE 104: HOOK NO EDGE 105: HOOK CLEAN 1 106: HOOK CLEAN 2 107: SOLO 88				No
AMP	35	B+ TIME CONST	knob					No
AMP	36	TUBE GRID BIAS	knob					No
AMP	39	BRight SWITCH	switch		0: Off	1: On		Yes
AMP	40	BOOST	switch		0: Off	1: On		Yes
AMP	41	LOW RES Q	knob					No
AMP	42	PREAMP BIAS	knob					No
AMP	43	HI FREQ	knob					No
AMP	44	HI RESONANCE	knob					No
AMP	45	CUT	switch		0: Off	1: On		No
AMP	46	XFORMER DRIVE	knob					No
AMP	47	INPUT TRIM	knob					Yes
AMP	48	PREAMP HARDNESS	knob					No
AMP	49	MV LOCATION	select	0: PRE-PI 1: POST-PI 2: PRE-TRIODE				No
AMP	50	SPEAKER DRIVE	knob					No
AMP	51	XFORMER MATCH	knob					No
AMP	54	SAT SWITCH	select	0: OFF 1: AUTH 2: IDEAL				No
AMP	55	GEQ BAND 1	slider					No
AMP	56	GEQ BAND 2	slider					No
AMP	57	GEQ BAND 3	slider					No
AMP	58	GEQ BAND 4	slider					No
AMP	59	GEQ BAND 5	slider					No
AMP	60	GEQ BAND 6	slider					No
AMP	61	GEQ BAND 7	slider					No
AMP	62	GEQ BAND 8	slider					No
AMP	63	BIAS EXCURSION	knob					No
AMP	66	TRIODE 2 PLATE FREQ	knob					No
AMP	67	TRIODE 1 PLATE FREQ	knob					No
AMP	68	PWR AMP TUBE	select	0: IDEAL TETRODE 1: IDEAL PENTODE 2: EL34/6CA7 3: EL84/6BQ5 4: 6L6/5881 5: 6V6 6: KT66 7: KT88 8: 6550 9: 6973 10: 6AQ5 11: 300B				No
AMP	69	PREAMP TUBES	select	0: 12AX7A SYL 1: ECC83 2: 7025 3: 12AX7A JJ 4: ECC803S 5: EF86 6: 12AX7A RCA 7: 12AX7A 8: 12AX7B				No
AMP	70	OUT COMP CLARITY	knob					No
AMP	71	CHARACTER Q	knob					No
AMP	72	CHARACTER FREQ	knob					No
AMP	73	CHARACTER AMT	knob					No
AMP	74	OVERDRIVE	knob					No
AMP	75	OUT COMP AMOUNT	knob					Yes
AMP	76	OUT COMP THRESHOLD	knob					No
AMP	77	MASTER TRIM	knob					Yes
AMP	78	FAT	switch		0: Off	1: On		No
AMP	79	DEFINITION	knob					No
AMP	80	PREAMP CF COMPRESS	knob					No
AMP	81	PREAMP CF TIME	knob					No
AMP	84	DYNAMIC PRESENCE	knob					No
AMP	85	DYNAMIC DEPTH	knob					No
AMP	86	POWER TYPE	select	0: AC 1: DC				No
AMP	87	AC LINE FREQ	knob					No
AMP	88	PWR AMP HARDNESS	knob					No
AMP	91	PREAMP CF RATIO	knob					No
AMP	92	EQ TYPE	select	0: 8 BAND VAR Q 1: 7 BAND VAR Q 2: 5 BAND (MARK) 3: 8 BAND CONST Q 4: 7 BAND CONST Q 5: 5 BAND CONST Q 6: 5 BAND PASSIVE 7: 4 BAND PASSIVE 8: 3 BAND PASSIVE 9: 3 BAND CONSOLE				No
AMP	93	CATHODE RESIST	knob					No
AMP	96	PREAMP SAG	switch		0: Off	1: On		No
AMP	97	BRight	knob					No
AMP	98	PWR AMP BIAS	knob					No
AMP	99	PREAMP DYNAMICS	knob					No
AMP	100	HI FREQ SLOPE	knob					No
AMP	101	VARIAC	knob					No
AMP	102	CHAR TYPE	select	0: SHELVING 1: PEAKING 2: DYNAMIC				No
AMP	104	PRESENCE SHIFT	switch		0: Off	1: On		No
AMP	105	SATURATION DRIVE	knob					Yes
AMP	106	CRUNCH	knob					No
AMP	109	OUT COMP TYPE	select	0: OUTPUT 1: FEEDBACK				No
AMP	110	EQ LOCATION	select	0: POST P.A. 1: PRE P.A.				No
AMP	111	CF COMP TYPE	select	0: AUTHENTIC 1: IDEAL				No
AMP	113	PREAMP CF HARDNESS	knob					No
AMP	114	PI BIAS SHIFT	knob					No
AMP	115	MOTOR DRIVE	knob					No	Since Quantum 7.02
AMP	116	MOTOR TIME CONST	knob					No	Since Quantum 7.02

Back to Top

CAB

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
CAB	0	CAB	select					No
CAB	1	MIC	select	0: None 1: 57 DYN 2: 58 DYN 3: 421 DYN 4: 87A COND 5: U87 COND 6: E609 DYN 7: RE16 DYN 8: R121 RIB 9: D112 DYN 10: 67 COND 11: NULL 12: INVERT				No
CAB	2	CAB R	select					No
CAB	3	MIC R	select	0: None 1: 57 DYN 2: 58 DYN 3: 421 DYN 4: 87A COND 5: U87 COND 6: E609 DYN 7: RE16 DYN 8: R121 RIB 9: D112 DYN 10: 67 COND 11: NULL 12: INVERT				No
CAB	4	LINK	switch		0: Off	1: On		No
CAB	5	Level L	knob					No
CAB	6	Level R	knob					No
CAB	7	Pan L	knob					No
CAB	8	Pan R	knob					No
CAB	9	Level	knob					Yes
CAB	10	Balance	knob					Yes
CAB	11	BYPASS MODE	select	0: THRU 1: MUTE				Yes
CAB	12	EFFECT TYPE	select	0: HI-/ULTRA-RES 1: NORMAL RES 2: STEREO 3: STEREO ULTRARES				No
CAB	14	DRIVE	knob					No
CAB	15	SATURATION	knob					No
CAB	16	ROOM Level	knob					No
CAB	17	ROOM SIZE	knob					No
CAB	18	MIC SPACING	knob					No
CAB	19	LOW CUT	knob					No
CAB	20	HIGH CUT	knob					No
CAB	21	SPEAKER SIZE	knob					No
CAB	22	PROXIMITY	knob					No
CAB	23	AIR	knob					No
CAB	24	MOTOR DRIVE	knob					No
CAB	25	AIR FREQ	knob					No
CAB	26	DELAY L	knob					No
CAB	27	DELAY R	knob					No
CAB	28	PROXIMITY R	knob					No
CAB	29	PROX. FREQ.	knob					No
CAB	30	INPUT SELECT	select	0: STEREO 1: Left 2: Right 3: SUM L+R				No
CAB	31	PREAMP TYPE	select	0: None 1: TUBE 2: BIPOLAR 3: FET I 4: FET II 5: TRANSFORMER 6: TAPE 70us 7: TAPE 50us 8: TAPE 35us 9: VINTAGE 10: MODERN 11: EXCITER				No
CAB	32	BASS	knob					No
CAB	33	MID	knob					No
CAB	34	TREBLE	knob					No
CAB	35	PREAMP MODE	select	0: ECONOMY 1: HIGH QUALITY				No
CAB	36	DEPHASE	knob					No
CAB	37	FILTER SLOPE	select	0: 6 dB/OCT 1: 12 dB/OCT				No
CAB	38	MOTOR TIME CONSTANT	knob					No

Back to Top

REV

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
REV	0	EFFECT TYPE	select	0: SMALL ROOM 1: MEDIUM ROOM 2: LARGE ROOM 3: SMALL HALL 4: MEDIUM HALL 5: LARGE HALL 6: SMALL CHAMBER 7: MEDIUM CHAMBER 8: LARGE CHAMBER 9: SMALL PLATE 10: MEDIUM PLATE 11: LARGE PLATE 12: SMALL CATHEDRAL 13: MED. CATHEDRAL 14: LARGE CATHEDRAL 15: SMALL SPRING 16: MEDIUM SPRING 17: LARGE SPRING 18: CAVERN 19: STONE QUARRY 20: STUDIO 21: AMBIENCE 22: CONCERT HALL 23: LARGE DEEP HALL 24: REC STUDIO C 25: NORTH CHURCH 26: SOUTH CHURCH 27: LONDON PLATE 28: SUN PLATE 29: HUGE ROOM 30: DRUM ROOM 31: HALLWAY 32: TUNNEL 33: DEEP CHAMBER 34: LG WOODEN ROOM 35: GYMNASIUM 36: ASYLUM HALL 37: DEEP SPACE 38: REC STUDIO A 39: LG TILED ROOM 40: VOCAL PLATE 41: WIDE HALL 42: RICH HALL				No
REV	1	TIME	knob					Yes
REV	2	HIGH CUT	knob					No
REV	3	HF TIME	knob					No
REV	4	WALL DIFFUSION	knob					No
REV	5	SIZE	knob					No
REV	7	EARLY Level	knob					No
REV	8	LATE Level	knob					No
REV	9	PREDELAY	knob					Yes
REV	10	LOW CUT	knob					No
REV	11	MOD DEPTH	knob					No
REV	12	MOD RATE	knob					No
REV	13	MIX	knob					Yes
REV	14	Level	knob					Yes
REV	15	Balance	knob					Yes
REV	16	BYPASS MODE	select	0: THRU 1: MUTE FX OUT 2: MUTE OUT 3: MUTE FX IN 4: MUTE IN				Yes
REV	17	GLOBAL	switch		0: Off	1: On		No
REV	18	INPUT GAIN	knob					Yes
REV	19	ECHO DENSITY	rangeKnob		2	8	1	No
REV	20	LATE DIFFUSION	knob					No
REV	21	LATE DIFF TIME	knob					No
REV	23	SPRING NUMBER	rangeKnob		2	6	1	No
REV	24	SPRING TONE	knob					No
REV	25	MIC SPACING	knob					No
REV	26	FREQ 1	knob					No
REV	27	FREQ 2	knob					No
REV	28	Q 1	knob					No
REV	29	Q 2	knob					No
REV	30	GAIN 1	knob					No
REV	31	GAIN 2	knob					No
REV	32	SPRING DRIVE	knob					No
REV	33	LF TIME	knob					No
REV	34	LF CROSSOVER	knob					No
REV	35	STEREO WIDTH	knob					No
REV	36	ATTEN	knob					No
REV	37	THRESHOLD	knob					No
REV	38	RELEASE TIME	knob					No
REV	39	EARLY DIFFUSION	knob					No
REV	40	EARLY DIFF TIME	knob					No
REV	41	EARLY DECAY	knob					No
REV	43	QUALITY	select	0: NORMAL 1: HIGH				No
REV	44	HOLD	switch		0: Off	1: On		Yes

Back to Top

DLY

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
DLY	0	EFFECT TYPE	select	0: DIGITAL MONO 1: DIGITAL STEREO 2: ANALOG MONO 3: ANALOG STEREO 4: MONO TAPE 5: STEREO TAPE 6: PING-PONG 7: DUAL DELAY 8: REVERSE DELAY 9: SWEEP DELAY 10: DUCKING DELAY 11: VINTAGE DIGITAL 12: 2290 W/ MOD 13: AMBIENT STEREO 14: DELUXE MIND GUY 15: MONO BBD 16: STEREO BBD 17: LO-FI TAPE				No
DLY	1	CONFIG	select	0: MONO 1: STEREO 2: PING-PONG 3: DUAL 4: REVERSE 5: SWEEP 6: TAPE				No
DLY	2	TIME	knob					Yes
DLY	3	RATIO	knob					Yes
DLY	4	FEEDBACK	knob					Yes
DLY	6	FEEDBACK R	knob					Yes
DLY	7	ECHO Pan	knob					Yes
DLY	8	SPREAD	knob					Yes
DLY	9	Tempo	select	Tempo Values				No
DLY	10	LOW CUT	knob					No
DLY	11	HIGH CUT	knob					No
DLY	12	LFO1 RATE	knob					Yes
DLY	13	LFO2 RATE	knob					Yes
DLY	14	LFO1 DEPTH	knob					Yes
DLY	15	LFO2 DEPTH	knob					Yes
DLY	16	DRIVE	knob					Yes
DLY	17	MIX	knob					Yes
DLY	18	Level	knob					Yes
DLY	19	Balance	knob					Yes
DLY	20	BYPASS MODE	select	0: THRU 1: MUTE FX OUT 2: MUTE OUT 3: MUTE FX IN 4: MUTE IN				Yes
DLY	21	GLOBAL	switch		0: Off	1: On		No
DLY	23	INPUT GAIN	knob					Yes
DLY	24	LFO1 TYPE	select	0: SINE 1: TRIANGLE 2: SQUARE 3: SAW UP 4: SAW DOWN 5: RANDOM 6: LOG 7: EXP 8: TRAPEZOID				No
DLY	25	LFO2 TYPE	select	0: SINE 1: TRIANGLE 2: SQUARE 3: SAW UP 4: SAW DOWN 5: RANDOM 6: LOG 7: EXP 8: TRAPEZOID				No
DLY	26	TIME R	knob					Yes
DLY	27	REPEAT HOLD	switch		0: Off	1: On		Yes
DLY	28	MASTER FEEDBACK	knob					Yes
DLY	29	Tempo R	select	Tempo Values				No
DLY	30	FEEDBACK L>R	knob					No
DLY	31	FEEDBACK R>L	knob					No
DLY	32	Level 1	knob					Yes
DLY	33	Level 2	knob					Yes
DLY	34	Pan 1	knob					No
DLY	35	Pan 2	knob					No
DLY	36	LFO1 PHASE	knob					Yes
DLY	37	LFO2 PHASE	knob					Yes
DLY	38	X FADE TIME	knob					No
DLY	39	RUN	switch		0: Off	1: On		No
DLY	40	TRIGGER RESTART	switch		0: Off	1: On		No
DLY	41	FILTER SLOPE	select	0: 6 dB/OCT 1: 12 dB/OCT 2: 24 dB/OCT 3: 36 dB/OCT 4: 48 dB/OCT				No
DLY	42	DUCK ATTN	knob					Yes
DLY	43	DUCK THRES	knob					No
DLY	44	DUCK RELEASE	knob					No
DLY	45	DIFFUSION	knob					Yes
DLY	46	DIFF TIME	knob					No
DLY	47	PHASE REVERSE	select	0: None 1: Right 2: Left 3: Both				No
DLY	48	LFO1 TARGET	select	0: Both 1: Left 2: Right				No
DLY	49	LFO2 TARGET	select	0: Both 1: Left 2: Right				No
DLY	50	LFO1 Tempo	select	Tempo Values				No
DLY	51	LFO2 Tempo	select	Tempo Values				No
DLY	52	SWEEP RATE	knob					No
DLY	53	SWEEP TYPE	select	0: SINE 1: TRIANGLE 2: SQUARE 3: SAW UP 4: SAW DOWN 5: RANDOM 6: LOG 7: EXP 8: TRAPEZOID				No
DLY	54	SWEEP PHASE	knob					No
DLY	55	SWEEP Tempo	select	Tempo Values				No
DLY	56	START FREQ	knob					No
DLY	57	STOP FREQ	knob					No
DLY	58	RESONANCE	knob					No
DLY	59	Q	knob					No
DLY	60	BIT REDUCTION	rangeKnob		0	24	1	Yes
DLY	61	FREQ 1	knob					No
DLY	62	FREQ 2	knob					No
DLY	63	Q 1	knob					No
DLY	64	Q 2	knob					No
DLY	65	GAIN 1	knob					No
DLY	66	GAIN 2	knob					No
DLY	67	LFO1 DEPTH RANGE	select	0: LOW 1: HIGH				Yes
DLY	68	MOTOR SPEED	knob					Yes
DLY	69	Right POST DELAY	knob					No

Back to Top

MTD

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
MTD	0	TIME 1	knob					No
MTD	1	TIME 2	knob					No
MTD	2	TIME 3	knob					No
MTD	3	TIME 4	knob					No
MTD	4	Tempo 1	select	Tempo Values				No
MTD	5	Tempo 2	select	Tempo Values				No
MTD	6	Tempo 3	select	Tempo Values				No
MTD	7	Tempo 4	select	Tempo Values				No
MTD	8	Level 1	knob					No
MTD	9	Level 2	knob					No
MTD	10	Level 3	knob					No
MTD	11	Level 4	knob					No
MTD	12	FEEDBACK 1	knob					No
MTD	13	FEEDBACK 2	knob					No
MTD	14	FEEDBACK 3	knob					No
MTD	15	FEEDBACK 4	knob					No
MTD	16	Pan 1	knob					No
MTD	17	Pan 2	knob					No
MTD	18	Pan 3	knob					No
MTD	19	Pan 4	knob					No
MTD	20	LFO1 RATE	knob					No
MTD	21	LFO2 RATE	knob					No
MTD	22	LFO3 RATE	knob					No
MTD	23	LFO4 RATE	knob					No
MTD	24	LFO1 Tempo	select	Tempo Values				No
MTD	25	LFO2 Tempo	select	Tempo Values				No
MTD	26	LFO3 Tempo	select	Tempo Values				No
MTD	27	LFO4 Tempo	select	Tempo Values				No
MTD	28	MIX	knob					Yes
MTD	29	Level	knob					Yes
MTD	30	Balance	knob					Yes
MTD	31	BYPASS MODE	select	0: THRU 1: MUTE FX OUT 2: MUTE OUT 3: MUTE FX IN 4: MUTE IN				Yes
MTD	32	GLOBAL MIX	switch		0: Off	1: On		No
MTD	33	INPUT GAIN	knob					Yes
MTD	35	EFFECT TYPE	select	0: QUAD-TAP 1: PLEX DELAY 2: PLEX DETUNE 3: PLEX SHIFT 4: BAND DELAY 5: QUAD-SERIES 6: TEN-TAP DLY 7: RHYTHM TAP 8: DIFFUSOR 9: QUAD TAPE DLY				No
MTD	36	DECAY TIME	knob					No
MTD	37	DIFFUSION	knob					No
MTD	38	INPUT DIFF	knob					No
MTD	39	DIFF TIME	knob					No
MTD	40	DUCKER THRES	knob					No
MTD	41	CROSSFADE	knob					No
MTD	42	MASTER TIME	knob					Yes
MTD	43	MASTER Level	knob					Yes
MTD	44	MASTER Pan	knob					Yes
MTD	45	MASTER FREQ	knob					Yes
MTD	46	MASTER Q	knob					Yes
MTD	47	MASTER FEEDBACK	knob					Yes
MTD	48	MASTER PITCH	knob					Yes
MTD	49	MASTER DETUNE	knob					Yes
MTD	50	DETUNE 1	knob					No
MTD	51	DETUNE 2	knob					No
MTD	52	DETUNE 3	knob					No
MTD	53	DETUNE 4	knob					No
MTD	54	SHIFT 1	rangeKnob		0	48	1	No
MTD	55	SHIFT 2	rangeKnob		0	48	1	No
MTD	56	SHIFT 3	rangeKnob		0	48	1	No
MTD	57	SHIFT 4	rangeKnob		0	48	1	No
MTD	58	FREQ 1	knob					Yes
MTD	59	FREQ 2	knob					Yes
MTD	60	FREQ 3	knob					Yes
MTD	61	FREQ 4	knob					Yes
MTD	62	Q 1	knob					No
MTD	63	Q 2	knob					No
MTD	64	Q 3	knob					No
MTD	65	Q 4	knob					No
MTD	66	MASTER RATE	knob					Yes
MTD	67	DUCKER ATTEN	knob					No
MTD	68	MASTER DEPTH	knob					Yes
MTD	69	DIRECTION	select	0: FORWARD 1: REVERSE				No
MTD	70	TAPE SPEED	knob					No
MTD	71	LFO1 DEPTH	knob					No
MTD	72	LFO2 DEPTH	knob					No
MTD	73	LFO3 DEPTH	knob					No
MTD	74	LFO4 DEPTH	knob					No
MTD	75	LFO1 MASTER	switch		0: Off	1: On		No
MTD	76	FB SEND	select	0: 1 1: 2 2: 3 3: 4				No
MTD	77	FB RETURN	select	0: 1 1: 2 2: 3 3: 4				No
MTD	78	MONO/STEREO	select	0: MONO 1: STEREO				No
MTD	79	DELAY TIME	knob					No
MTD	81	QUANTIZE	select	Tempo Values				No
MTD	82	DECAY	knob					No
MTD	84	NUMBER OF TAPS	rangeKnob		1	10	1	No
MTD	85	SHUFFLE	knob					No
MTD	86	DELAY Tempo	select	Tempo Values				No
MTD	87	SPREAD	knob					No
MTD	88	Pan SHAPE	select	0: CONSTANT 1: INCREASING 2: DECREASING 3: UP / DOWN 4: DOWN / UP 5: SINE				No
MTD	89	Pan ALPHA	knob					No
MTD	90	LOW CUT	knob					No
MTD	91	HIGH CUT	knob					No
MTD	92	RATIO	knob					No
MTD	93	FEEDBACK	knob					No
MTD	94	TAP 1 TIME	knob					No
MTD	95	TAP 2 TIME	knob					No
MTD	96	TAP 3 TIME	knob					No
MTD	97	TAP 4 TIME	knob					No
MTD	98	TAP 5 TIME	knob					No
MTD	99	TAP 6 TIME	knob					No
MTD	100	TAP 7 TIME	knob					No
MTD	101	TAP 8 TIME	knob					No
MTD	102	TAP 9 TIME	knob					No
MTD	103	TAP 10 TIME	knob					No
MTD	104	TAP 1 Level	knob					No
MTD	105	TAP 2 Level	knob					No
MTD	106	TAP 3 Level	knob					No
MTD	107	TAP 4 Level	knob					No
MTD	108	TAP 5 Level	knob					No
MTD	109	TAP 6 Level	knob					No
MTD	110	TAP 7 Level	knob					No
MTD	111	TAP 8 Level	knob					No
MTD	112	TAP 9 Level	knob					No
MTD	113	TAP 10 Level	knob					No
MTD	116	DUCKER RELEASE	knob					No
MTD	117	DRIVE	knob					No

Back to Top

CHO

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
CHO	0	EFFECT TYPE	select	0: DIGITAL MONO 1: DIGITAL STEREO 2: ANALOG MONO 3: ANALOG STEREO 4: JAPan CE-2 5: WARM STEREO 6: 80'S STYLE 7: TRIANGLE CHORUS 8: 8-VOICE STEREO 9: VINTAGE TAPE 10: DIMENSION 1 11: DIMENSION 2 12: 4-VOICE ANALOG				No
CHO	1	VOICES	rangeKnob		1	4	1	No
CHO	2	RATE	knob					Yes
CHO	3	Tempo	select	Tempo Values				No
CHO	4	DEPTH	knob					Yes
CHO	5	HIGH CUT	knob					No
CHO	6	DELAY TIME	knob					No
CHO	7	LFO PHASE	knob					No
CHO	8	LFO TYPE	select	0: SINE 1: TRIANGLE 2: SQUARE 3: SAW UP 4: SAW DOWN 5: RANDOM 6: LOG 7: EXP 8: TRAPEZOID				No
CHO	9	AUTO DEPTH	select	0: OFF 1: LOW 2: HIGH				No
CHO	10	MIX	knob					Yes
CHO	11	Level	knob					Yes
CHO	12	Balance	knob					Yes
CHO	13	BYPASS MODE	select	0: THRU 1: MUTE FX OUT 2: MUTE OUT				Yes
CHO	14	GLOBAL	switch		0: Off	1: On		No
CHO	16	PHASE REVERSE	select	0: None 1: Right 2: Left 3: Both				No
CHO	17	WIDTH	knob					No
CHO	18	LFO 2 RATE	knob					No
CHO	19	LFO 2 DEPTH	knob					No
CHO	20	DRIVE	knob					No
CHO	21	LOW CUT	knob					No
CHO	22	SPREAD	knob					No
CHO	23	DIMENSION	select	0: OFF 1: LOW 2: MED 3: HIGH				No

Back to Top

FLG

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
FLG	0	EFFECT TYPE	select	0: DIGITAL MONO 1: DIGITAL STEREO 2: ANALOG MONO 3: ANALOG STEREO 4: THRU-ZERO 5: STEREO JET 6: ZERO FLANGER 7: POP FLANGER				No
FLG	1	RATE	knob					Yes
FLG	2	Tempo	select	Tempo Values				No
FLG	3	DEPTH	knob					Yes
FLG	4	FEEDBACK	knob					Yes
FLG	5	DELAY TIME	knob					Yes
FLG	6	DRY DELAY SHIFT	knob					No
FLG	7	LFO PHASE	knob					No
FLG	8	LFO TYPE	select	0: SINE 1: TRIANGLE 2: SQUARE 3: SAW UP 4: SAW DOWN 5: RANDOM 6: LOG 7: EXP 8: TRAPEZOID				No
FLG	9	LFO HIGHCUT	knob					No
FLG	10	AUTO DEPTH	select	0: OFF 1: LOW 2: MED 3: HIGH				No
FLG	11	MIX	knob					Yes
FLG	12	Level	knob					Yes
FLG	13	Balance	knob					Yes
FLG	14	BYPASS MODE	select	0: THRU 1: MUTE FX OUT 2: MUTE OUT				Yes
FLG	15	GLOBAL	switch		0: Off	1: On		No
FLG	17	PHASE REVERSE	select	0: None 1: Right 2: Left 3: Both				No
FLG	18	THRU ZERO	switch		0: Off	1: On		No
FLG	19	HIGH CUT	knob					No
FLG	20	DRIVE	knob					No
FLG	21	LOW CUT	knob					No
FLG	22	SPREAD	knob					No

Back to Top

ROT

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
ROT	0	RATE	knob					Yes
ROT	1	LOW DEPTH	knob					No
ROT	2	HI DEPTH	knob					No
ROT	3	HI Level	knob					No
ROT	4	Tempo	select	Tempo Values				No
ROT	5	MIX	knob					Yes
ROT	6	Level	knob					Yes
ROT	7	Balance	knob					Yes
ROT	8	BYPASS MODE	select	0: THRU 1: MUTE FX OUT 2: MUTE OUT				Yes
ROT	10	ROTOR LENGTH	knob					No
ROT	12	MIC SPACING	knob					No
ROT	13	LOW RATE MULT	knob					No
ROT	14	LOW TIME CONST	knob					No
ROT	15	HI TIME CONST	knob					No
ROT	16	STEREO SPREAD	knob					No
ROT	17	DRIVE	knob					No
ROT	18	MIC DISTANCE	knob					No

Back to Top

PHA

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
PHA	0	EFFECT TYPE	select	0: DIGITAL MONO 1: DIGITAL STEREO 2: SCRIPT 45 3: SCRIPT 90 4: BLOCK 90 5: CLASSIC VIBE 6: STEREO 8-STAGE 7: BARBERPOLE				No
PHA	1	ORDER	select	0: 2 1: 4 2: 6 3: 8 4: 10 5: 12				No
PHA	2	RATE	knob					Yes
PHA	3	LFO TYPE	select	0: SINE 1: TRIANGLE 2: SQUARE 3: SAW UP 4: SAW DOWN 5: RANDOM 6: LOG 7: EXP 8: TRAPEZOID				No
PHA	4	Tempo	select	Tempo Values				No
PHA	5	DEPTH	knob					Yes
PHA	6	FEEDBACK	knob					Yes
PHA	7	FREQ. START	knob					No
PHA	8	FREQ. SPan	knob					No
PHA	9	LFO PHASE	knob					No
PHA	10	BULB BIAS	knob					No
PHA	11	MIX	knob					Yes
PHA	12	Level	knob					Yes
PHA	13	Balance	knob					Yes
PHA	14	BYPASS MODE	select	0: THRU 1: MUTE FX OUT 2: MUTE OUT				Yes
PHA	15	GLOBAL	switch		0: Off	1: On		No
PHA	17	MODE	select	0: NORMAL 1: VIBE 2: BARBERPOLE				No
PHA	18	FEEDBACK TAP	switch		0: Off	1: On		No
PHA	19	TONE	knob					No
PHA	20	DIRECTION	select	0: UP 1: DOWN				No
PHA	21	FILTER Q	knob					No
PHA	22	LFO BYPASS RESET	select	0: OFF 1: 0 DEG 2: 90 DEG 3: 180 DEG 4: 270 DEG				No

Back to Top

WAH

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
WAH	0	EFFECT TYPE	select	0: FAS STANDARD 1: CLYDE 2: CRY BABE 3: VX846 4: COLOR-TONE 5: FUNK 6: MORTAL 7: VX845				No
WAH	1	FREQ MIN	knob					No
WAH	2	FREQ MAX	knob					No
WAH	3	RESONANCE	knob					No
WAH	4	TRACKING	knob					No
WAH	5	CONTROL	knob					Yes
WAH	6	Level	knob					Yes
WAH	7	Balance	knob					Yes
WAH	8	BYPASS MODE	select	0: THRU 1: MUTE				Yes
WAH	9	FAT	knob					No
WAH	10	DRIVE	knob					No
WAH	11	TAPER	select	0: LINEAR 1: LOG 30A 2: LOG 20A 3: LOG 15A 4: LOG 10A 5: LOG 5A				No
WAH	13	COIL BIAS	knob					No	Since Quantum 6
WAH	14	LOW CUT FREQ	knob					No	Since Quantum 6

Back to Top

FRM

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
FRM	0	START	select	0: AAA 1: EEE 2: III 3: OHH 4: OOO 5: EHH 6: AHH 7: AWW 8: UHH 9: ERR				No
FRM	1	MID	select	0: AAA 1: EEE 2: III 3: OHH 4: OOO 5: EHH 6: AHH 7: AWW 8: UHH 9: ERR				No
FRM	2	END	select	0: AAA 1: EEE 2: III 3: OHH 4: OOO 5: EHH 6: AHH 7: AWW 8: UHH 9: ERR				No
FRM	3	RESONANCE	knob					Yes
FRM	4	CONTROL	knob					Yes
FRM	5	MIX	knob					Yes
FRM	6	Level	knob					Yes
FRM	7	Balance	knob					Yes
FRM	8	BYPASS MODE	select	0: THRU 1: MUTE FX OUT 2: MUTE OUT				Yes
FRM	9	GLOBAL	switch		0: Off	1: On		No

Back to Top

VOL

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
VOL	0	VOLUME	knob					Yes
VOL	1	Balance	knob					Yes
VOL	2	VOLUME TAPER	select	0: LINEAR 1: LOG 30A 2: LOG 20A 3: LOG 15A 4: LOG 10A 5: LOG 5A				No
VOL	4	Pan Left	knob					Yes
VOL	5	Pan Right	knob					Yes
VOL	6	Level	knob					Yes
VOL	7	BYPASS MODE	select	0: THRU 1: MUTE				Yes
VOL	8	INPUT SELECT	select	0: STEREO 1: Left ONLY 2: Right ONLY				No

Back to Top

TRM

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
TRM	0	EFFECT TYPE	select	0: TREMOLO 1: PanNER				No
TRM	1	LFO TYPE	select	0: SINE 1: TRIANGLE 2: SQUARE 3: SAW UP 4: SAW DOWN 5: RANDOM 6: LOG 7: EXP 8: TRAPEZOID				No
TRM	2	RATE	knob					Yes
TRM	3	DEPTH	knob					Yes
TRM	4	DUTY	knob					Yes
TRM	5	Tempo	select	Tempo Values				No
TRM	7	Level	knob					Yes
TRM	8	Balance	knob					Yes
TRM	9	BYPASS MODE	select	0: THRU 1: MUTE				Yes
TRM	11	LFO PHASE	knob					Yes
TRM	12	WIDTH	knob					Yes
TRM	13	Pan CENTER	knob					No
TRM	15	START PHASE	knob					No

Back to Top

PIT

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
PIT	0	EFFECT TYPE	select	0: DETUNE 1: FIXED HARM 2: INTEL HARM 3: CL. WHAMMY 4: OCTAVE DIV 5: CRYSTALS 6: AD. WHAMMY 7: ARPEGGIATOR 8: CUST. SHIFT				No
PIT	1	MODE	select	DN 1 OCT 5: UP|DN 2 OCT				No
PIT	2	MASTER PITCH	knob					Yes
PIT	3	CONTROL	knob					Yes
PIT	4	VOICE 1 HARMONY	rangeKnob		0	48	1	No
PIT	5	VOICE 2 HARMONY	rangeKnob		0	48	1	No
PIT	6	KEY	select	0: A 1: Bb 2: B 3: C 4: Db 5: D 6: Eb 7: E 8: F 9: Gb 10: G 11: Ab				No
PIT	7	SCALE	select	0: IONIAN MAJ 1: DORIAN 2: PHRYGIAN 3: LYDIAN 4: MIXOLYDIAN 5: AEOLIAN MIN 6: LOCRIAN 7: MEL. MINOR 8: HARM. MINOR 9: DIMINISHED 10: WHOLE TONE 11: DOM. SEVEN 12: DIM. WHOLE 13: PENTA. MAJ 14: PENTA. MIN 15: BLUES 16: CHROMATIC 17: CUSTOM				No
PIT	8	TRACK MODE	select	0: SMOOTH 1: STEPPED				No
PIT	9	VOICE 1 DETUNE	knob					Yes
PIT	10	VOICE 2 DETUNE	knob					Yes
PIT	11	VOICE 1 SHIFT	rangeKnob		0	48	1	Yes
PIT	12	VOICE 2 SHIFT	rangeKnob		0	48	1	Yes
PIT	13	VOICE 1 Level	knob					Yes
PIT	14	VOICE 2 Level	knob					Yes
PIT	15	VOICE 1 Pan	knob					Yes
PIT	16	VOICE 2 Pan	knob					Yes
PIT	17	VOICE 1 DELAY	knob					No
PIT	18	VOICE 2 DELAY	knob					No
PIT	19	VOICE 1 FEEDBACK	knob					No
PIT	20	VOICE 2 FEEDBACK	knob					No
PIT	21	PITCH TRACK	select	0: OFF 1: POLY 2: MONO				No
PIT	22	TRACK ADJUST	knob					No
PIT	23	MIX	knob					Yes
PIT	24	Level	knob					Yes
PIT	25	Balance	knob					Yes
PIT	26	BYPASS MODE	select	0: THRU 1: MUTE FX OUT 2: MUTE OUT 3: MUTE FX IN 4: MUTE IN				Yes
PIT	27	GLOBAL	switch		0: Off	1: On		No
PIT	28	INPUT GAIN	knob					Yes
PIT	30	CROSSFADE	knob					No
PIT	31	VOICE 1 SPLICE	knob					No
PIT	32	VOICE 2 SPLICE	knob					No
PIT	33	VOICE 1 Tempo	select	Tempo Values				No
PIT	34	VOICE 2 Tempo	select	Tempo Values				No
PIT	35	SPLC1 Tempo	select	Tempo Values				No
PIT	36	SPLC2 Tempo	select	Tempo Values				No
PIT	37	FEEDBACK TYPE	select	0: DUAL 1: Both 2: PING-PONG				No
PIT	38	REVERSE	switch		0: Off	1: On		No
PIT	39	HI CUT	knob					No
PIT	40	GLIDE TIME	knob					No
PIT	41	MASTER DELAY	knob					Yes
PIT	42	MASTER FEEDBACK	knob					Yes
PIT	43	MASTER Pan	knob					Yes
PIT	44	MASTER Level	knob					Yes
PIT	45	Notes	select	4: 4 5: 5 6: 6 7: 7 8: 8	4			No
PIT	53	VOICE 1 SCALE	rangeKnob		0	31	1	Yes
PIT	54	VOICE 2 SCALE	rangeKnob		0	31	1	Yes
PIT	55	STAGES	rangeKnob		2	16	1	No
PIT	56	REPEATS	select	1: 1 2: 2 3: 3 4: 4 5: 5 6: 6 7: 7 8: 8 9: 9 10: 10 11: 11 12: 12 13: 13 14: 14 15: 15 16: 16 17: 17 18: 18 19: 19 20: 20 21: 21 22: 22 23: 23 24: 24 25: 25 26: 26 27: 27 28: 28 29: 29 30: 30 31: Infinite	1			No
PIT	57	RUN	switch		0: Off	1: On		Yes
PIT	58	Tempo	select	Tempo Values	1			No
PIT	59	STAGE 1 SHIFT	rangeKnob		0	48	1	No
PIT	60	STAGE 2 SHIFT	rangeKnob		0	48	1	No
PIT	61	STAGE 3 SHIFT	rangeKnob		0	48	1	No
PIT	62	STAGE 4 SHIFT	rangeKnob		0	48	1	No
PIT	63	STAGE 5 SHIFT	rangeKnob		0	48	1	No
PIT	64	STAGE 6 SHIFT	rangeKnob		0	48	1	No
PIT	65	STAGE 7 SHIFT	rangeKnob		0	48	1	No
PIT	66	STAGE 8 SHIFT	rangeKnob		0	48	1	No
PIT	67	STAGE 9 SHIFT	rangeKnob		0	48	1	No
PIT	68	STAGE 10 SHIFT	rangeKnob		0	48	1	No
PIT	69	STAGE 11 SHIFT	rangeKnob		0	48	1	No
PIT	70	STAGE 12 SHIFT	rangeKnob		0	48	1	No
PIT	71	STAGE 13 SHIFT	rangeKnob		0	48	1	No
PIT	72	STAGE 14 SHIFT	rangeKnob		0	48	1	No
PIT	73	STAGE 15 SHIFT	rangeKnob		0	48	1	No
PIT	74	STAGE 16 SHIFT	rangeKnob		0	48	1	No
PIT	75	AMPLITUBE SHAPE	select	0: CONSTANT 1: INCREASING 2: DECREASING 3: UP / DOWN 4: DOWN / UP 5: SINE				No
PIT	76	AMPLITUBE ALPHA	knob					No
PIT	77	Pan SHAPE	select	0: CONSTANT 1: INCREASING 2: DECREASING 3: UP / DOWN 4: DOWN / UP 5: SINE				No
PIT	78	Pan ALPHA	knob					No
PIT	79	VOICE 1 DELAY	knob					No
PIT	80	VOICE 2 DELAY	knob					No
PIT	81	PITCH SOURCE	select	0: GLOBAL 1: LOCAL				No
PIT	82	INPUT MODE	select	0: MONO 1: STEREO				No
PIT	83	LEARN	switch		0: Off	1: On		Yes
PIT	84	LOW CUT	knob					No
PIT	85	ECONOMY	switch		0: Off	1: On		No

Back to Top

FIL

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
FIL	0	EFFECT TYPE	select	0: NULL 1: LOWPASS 2: BANDPASS 3: HIGHPASS 4: LOWSHELF 5: HIGHSHLF 6: PEAKING 7: NOTCH 8: TILT EQ 9: LOWSHELF2 10: HIGHSHLF2 11: PEAKING2				No
FIL	1	FREQUENCY	knob					Yes
FIL	2	Q	knob					Yes
FIL	3	GAIN	knob					Yes
FIL	4	Level	knob					Yes
FIL	5	Balance	knob					Yes
FIL	6	BYPASS MODE	select	0: THRU 1: MUTE				Yes
FIL	7	ORDER	select	0: 2nd 1: 4th				No
FIL	9	Pan Left	knob					No
FIL	10	Pan Right	knob					No
FIL	11	INVERT	select	0: None 1: Right 2: Left 3: Both				No
FIL	12	LOW CUT	knob					No
FIL	13	HI CUT	knob					No

Back to Top

DRV

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
DRV	0	EFFECT TYPE	select	0: RAT DIST 1: PI FUZZ 2: TUBE DRV 3-KNOB 3: SUPER OD 4: TREBLE BOOST 5: MID BOOST 6: T808 OD 7: FAT RAT 8: T808 MOD 9: OCTAVE DIST 10: PLUS DIST 11: HARD FUZZ 12: FET BOOST 13: TAPE DIST 14: FULL OD 15: BLUES OD 16: SHRED DIST 17: M-ZONE DIST 18: BENDER FUZZ 19: BB PRE 20: MASTER FUZZ 21: FACE FUZZ 22: BIT CRUSHER 23: ETERNAL LOVE 24: ESOTERIC ACB 25: ESOTERIC RCB 26: ZEN MASTER 27: TUBE DRV 4-KNOB 28: FAS LED-DRIVE 29: SDD PREAMP 30: FET PREAMP 31: RUCKUS 32: MICRO BOOST 33: FAS BOOST 34: TIMOTHY 35: SHIMMER DRIVE				No
DRV	1	GAIN	knob					Yes
DRV	2	TONE	knob					Yes
DRV	3	VOLUME	knob					Yes
DRV	4	MIX	knob					Yes
DRV	5	BYPASS MODE	select	0: THRU 1: MUTE				Yes
DRV	6	SLEW LIMIT	knob					No
DRV	8	LO CUT	knob					No
DRV	9	HI CUT	knob					No
DRV	10	CLIP TYPE	select	0: LV TUBE 1: HARD 2: SOFT 3: GERMANIUM 4: FW RECT 5: HV TUBE 6: SILICON 7: 4558/DIODE 8: LED 9: FET 10: OP-AMP 11: VARIABLE 12: NULL				No
DRV	11	BIAS	knob					No
DRV	12	BASS	knob					No
DRV	13	MIDDLE	knob					No
DRV	14	MID FREQ	knob					No
DRV	15	TREBLE	knob					No
DRV	16	BIT REDUCE	rangeKnob		0	24	1	Yes
DRV	17	INPUT	select	0: L+R 1: Left 2: Right				No
DRV	18	Balance	knob					Yes
DRV	19	SAMPLE RATE	knob					Yes

Back to Top

ENH

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
ENH	0	WIDTH	knob					No
ENH	1	DEPTH	knob					No
ENH	2	LOW CUT	knob					No
ENH	3	HIGH CUT	knob					No
ENH	4	Level	knob					No
ENH	6	EFFECT TYPE	select	0: MODERN 1: CLASSIC				No
ENH	7	INVERT	select	0: None 1: Right 2: Left 3: Both				No
ENH	8	Pan Left	knob					No
ENH	9	Pan Right	knob					No
ENH	10	Balance	knob					No

Back to Top

FXL

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
FXL	0	Level 1	knob					No
FXL	1	Level 2	knob					No
FXL	2	Level 3	knob					No
FXL	3	Level 4	knob					No
FXL	4	Pan 1	knob					No
FXL	5	Pan 2	knob					No
FXL	6	Pan 3	knob					No
FXL	7	Pan 4	knob					No
FXL	8	SCENE 1	slider					No
FXL	9	SCENE 2	slider					No
FXL	10	SCENE 3	slider					No
FXL	11	SCENE 4	slider					No
FXL	12	SCENE 5	slider					No
FXL	13	SCENE 6	slider					No
FXL	14	SCENE 7	slider					No
FXL	15	SCENE 8	slider					No
FXL	16	Level	knob					Yes
FXL	17	Balance	knob					Yes
FXL	18	BYPASS MODE	select	0: THRU 1: MUTE				Yes

Back to Top

INPUT

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
INPUT	0	THRESHOLD	knob					Yes
INPUT	1	RATIO	knob					Yes
INPUT	2	RELEASE	knob					No
INPUT	3	ATTACK	knob					No
INPUT	4	INPUT Z	select	0: AUTO: 1: 1M 2: 1M+CAP 3: 230K 4: 230K+CAP 5: 90K 6: 90K+CAP 7: 70K 8: 70K+CAP 9: 32K 10: 32K+CAP 11: 22K 12: 22K+CAP				No
INPUT	5	Level	knob					No
INPUT	7	EFFECT TYPE	select	0: CLASSIC 1: INTELLIGENT				No

Back to Top

OUTPUT

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
OUTPUT	0	Level 1	knob					No
OUTPUT	1	Level 2	knob					No
OUTPUT	2	Level 3	knob					No
OUTPUT	3	Level 4	knob					No
OUTPUT	4	Balance 1	knob					No
OUTPUT	5	Balance 2	knob					No
OUTPUT	6	Balance 3	knob					No
OUTPUT	7	Balance 4	knob					No
OUTPUT	8	SCENE 1 MAIN	slider					No
OUTPUT	9	SCENE 2 MAIN	slider					No
OUTPUT	10	SCENE 3 MAIN	slider					No
OUTPUT	11	SCENE 4 MAIN	slider					No
OUTPUT	12	SCENE 5 MAIN	slider					No
OUTPUT	13	SCENE 6 MAIN	slider					No
OUTPUT	14	SCENE 7 MAIN	slider					No
OUTPUT	15	SCENE 8 MAIN	slider					No
OUTPUT	16	Level	knob					No
OUTPUT	17	Pan	knob					No
OUTPUT	18	BYPASS MODE	select	0: THRU 1: MUTE				No

Back to Top

CONTROLLERS

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
CONTROLLERS	0	LFO1 TYPE [RUN]	select	0: SINE 1: TRIANGLE 2: SQUARE 3: SAW UP 4: SAW DOWN 5: RANDOM 6: LOG 7: EXP 8: TRAPEZOID				Yes
CONTROLLERS	1	LFO1 RATE	knob					Yes
CONTROLLERS	2	LFO1 DEPTH	knob					Yes
CONTROLLERS	3	LFO1 DUTY	knob					Yes
CONTROLLERS	4	OUTPUT B PHASE	knob					No
CONTROLLERS	5	LFO1 Tempo	select	Tempo Values				No
CONTROLLERS	6	LFO2 TYPE [RUN]	select	0: SINE 1: TRIANGLE 2: SQUARE 3: SAW UP 4: SAW DOWN 5: RANDOM 6: LOG 7: EXP 8: TRAPEZOID				Yes
CONTROLLERS	7	LFO2 RATE	knob					Yes
CONTROLLERS	8	LFO2 DEPTH	knob					Yes
CONTROLLERS	9	LFO2 DUTY	knob					Yes
CONTROLLERS	10	OUTPUT B PHASE	knob					No
CONTROLLERS	11	LFO2 Tempo	select	Tempo Values				No
CONTROLLERS	12	MODE	select	0: ONCE 1: LOOP 2: SUST				No
CONTROLLERS	13	RETRIG	switch		0: Off	1: On		No
CONTROLLERS	14	ATTACK	knob					No
CONTROLLERS	15	DECAY	knob					No
CONTROLLERS	16	SUSTAIN	knob					No
CONTROLLERS	17	Level	knob					No
CONTROLLERS	18	RELEASE	knob					No
CONTROLLERS	19	THRESHOLD	knob					No
CONTROLLERS	20	MODE	select	0: ONCE 1: LOOP 2: SUST				No
CONTROLLERS	21	RETRIG	switch		0: Off	1: On		No
CONTROLLERS	22	ATTACK	knob					No
CONTROLLERS	23	DECAY	knob					No
CONTROLLERS	24	SUSTAIN	knob					No
CONTROLLERS	25	Level	knob					No
CONTROLLERS	26	RELEASE	knob					No
CONTROLLERS	27	THRESHOLD	knob					No
CONTROLLERS	28	ATTACK	knob					No
CONTROLLERS	29	RELEASE	knob					No
CONTROLLERS	30	THRESHOLD	knob					No
CONTROLLERS	31	GAIN	knob					No
CONTROLLERS	32	TAP Tempo	rangeKnob		30	250	1	No
CONTROLLERS	33	Tempo SETTING	select	0: PRESET 1: GLOBAL				No
CONTROLLERS	34	RATE	knob					Yes
CONTROLLERS	35	Tempo	select	Tempo Values				No
CONTROLLERS	36	STAGES	select	2: 2 3: 3 4: 4 5: 5 6: 6 7: 7 8: 8 9: 9 10: 10 11: 11 12: 12 13: 13 14: 14 15: 15 16: 16 17: 17 18: 18 19: 19 20: 20 21: 21 22: 22 23: 23 24: 24 25: 25 26: 26 27: 27 28: 28 29: 29 30: 30 31: 31 32: 32	2			No
CONTROLLERS	37	1	slider					No
CONTROLLERS	38	2	slider					No
CONTROLLERS	39	3	slider					No
CONTROLLERS	40	4	slider					No
CONTROLLERS	41	5	slider					No
CONTROLLERS	42	6	slider					No
CONTROLLERS	43	7	slider					No
CONTROLLERS	44	8	slider					No
CONTROLLERS	45	9	slider					No
CONTROLLERS	46	10	slider					No
CONTROLLERS	47	11	slider					No
CONTROLLERS	48	12	slider					No
CONTROLLERS	49	13	slider					No
CONTROLLERS	50	14	slider					No
CONTROLLERS	51	15	slider					No
CONTROLLERS	52	16	slider					No
CONTROLLERS	54	RUN	switch		0: Off	1: On		Yes
CONTROLLERS	55	A	knob					No
CONTROLLERS	56	B	knob					No
CONTROLLERS	57	C	knob					No
CONTROLLERS	58	D	knob					No
CONTROLLERS	59	17	slider					No
CONTROLLERS	60	18	slider					No
CONTROLLERS	61	19	slider					No
CONTROLLERS	62	20	slider					No
CONTROLLERS	63	21	slider					No
CONTROLLERS	64	22	slider					No
CONTROLLERS	65	23	slider					No
CONTROLLERS	66	24	slider					No
CONTROLLERS	67	25	slider					No
CONTROLLERS	68	26	slider					No
CONTROLLERS	69	27	slider					No
CONTROLLERS	70	28	slider					No
CONTROLLERS	71	29	slider					No
CONTROLLERS	72	30	slider					No
CONTROLLERS	73	31	slider					No
CONTROLLERS	74	32	slider					No
CONTROLLERS	77	RUN	switch		0: Off	1: On		No
CONTROLLERS	78	SCENE 1	knob					No
CONTROLLERS	79	SCENE 2	knob					No
CONTROLLERS	80	SCENE 3	knob					No
CONTROLLERS	81	SCENE 4	knob					No
CONTROLLERS	82	SCENE 5	knob					No
CONTROLLERS	83	SCENE 6	knob					No
CONTROLLERS	84	SCENE 7	knob					No
CONTROLLERS	85	SCENE 8	knob					No
CONTROLLERS	86	SCENE 1	knob					No
CONTROLLERS	87	SCENE 2	knob					No
CONTROLLERS	88	SCENE 3	knob					No
CONTROLLERS	89	SCENE 4	knob					No
CONTROLLERS	90	SCENE 5	knob					No
CONTROLLERS	91	SCENE 6	knob					No
CONTROLLERS	92	SCENE 7	knob					No
CONTROLLERS	93	SCENE 8	knob					No
CONTROLLERS	94	QUANTIZE	select	1: OFF 2: 2 3: 3 4: 4 5: 5 6: 6 7: 7 8: 8 9: 9 10: 10 11: 11 12: 12 13: 13 14: 14 15: 15 16: 16 17: 17 18: 18 19: 19 20: 20 21: 21 22: 22 23: 23 24: 24 25: 25 26: 26 27: 27 28: 28 29: 29 30: 30 31: 31 32: 32	1			No
CONTROLLERS	95	QUANTIZE	select	1: OFF 2: 2 3: 3 4: 4 5: 5 6: 6 7: 7 8: 8 9: 9 10: 10 11: 11 12: 12 13: 13 14: 14 15: 15 16: 16 17: 17 18: 18 19: 19 20: 20 21: 21 22: 22 23: 23 24: 24 25: 25 26: 26 27: 27 28: 28 29: 29 30: 30 31: 31 32: 32	1			No

Back to Top

SYN

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
SYN	0	TYPE 1	select	0: SINE 1: TRIANGLE 2: SQUARE 3: SAWTOOTH 4: RANDOM 5: WHT NOISE 6: PINK NOISE 7: OFF				No
SYN	1	FREQUENCY 1	knob					Yes
SYN	2	TRACK 1	select	0: OFF 1: ENV ONLY 2: PITCH+ENV 3: QUANTIZE				No
SYN	3	SHIFT 1	knob					Yes
SYN	4	TUNE 1	knob					Yes
SYN	5	DUTY 1	knob					Yes
SYN	6	VOICE Level 1	knob					Yes
SYN	7	VOICE Pan 1	knob					Yes
SYN	8	ATTACK 1	knob					No
SYN	9	FILTER 1	knob					Yes
SYN	10	Q 1	knob					No
SYN	11	TYPE 2	select	0: SINE 1: TRIANGLE 2: SQUARE 3: SAWTOOTH 4: RANDOM 5: WHT NOISE 6: PINK NOISE 7: OFF				No
SYN	12	FREQUENCY 2	knob					Yes
SYN	13	TRACK 2	select	0: OFF 1: ENV ONLY 2: PITCH+ENV 3: QUANTIZE				No
SYN	14	SHIFT 2	knob					Yes
SYN	15	TUNE 2	knob					Yes
SYN	16	DUTY 2	knob					Yes
SYN	17	VOICE Level 2	knob					Yes
SYN	18	VOICE Pan 2	knob					Yes
SYN	19	ATTACK 2	knob					No
SYN	20	FILTER 2	knob					Yes
SYN	21	Q 2	knob					No
SYN	23	MIX	knob					Yes
SYN	24	Level	knob					Yes
SYN	25	Balance	knob					Yes
SYN	26	BYPASS MODE	select	0: THRU 1: MUTE FX OUT 2: MUTE OUT				Yes
SYN	27	GLOBAL MIX	switch		0: Off	1: On		No
SYN	29	TYPE 3	select	0: SINE 1: TRIANGLE 2: SQUARE 3: SAWTOOTH 4: RANDOM 5: WHT NOISE 6: PINK NOISE 7: OFF				No
SYN	30	FREQUENCY 3	knob					Yes
SYN	31	TRACK 3	select	0: OFF 1: ENV ONLY 2: PITCH+ENV 3: QUANTIZE				No
SYN	32	SHIFT 3	knob					Yes
SYN	33	TUNE 3	knob					Yes
SYN	34	DUTY 3	knob					Yes
SYN	35	VOICE Level 3	knob					Yes
SYN	36	VOICE Pan 3	knob					Yes
SYN	37	ATTACK 3	knob					No
SYN	38	FILTER 3	knob					Yes
SYN	39	Q 3	knob					No

Back to Top

GTE

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
GTE	0	THRESHOLD	knob					Yes
GTE	1	ATTACK	knob					No
GTE	2	HOLD	knob					No
GTE	3	RELEASE	knob					No
GTE	4	RATIO	knob					Yes
GTE	5	SIDECHAIN SELECT	select	0: BLOCK L+R 1: ROW 1 2: ROW 2 3: ROW 3 4: ROW 4 5: INPUT 1 6: INPUT 2				No
GTE	6	LOW CUT	knob					No
GTE	7	HIGH CUT	knob					No
GTE	9	Level	knob					Yes
GTE	10	Balance	knob					Yes
GTE	11	BYPASS MODE	select	0: THRU 1: MUTE				Yes

Back to Top

RNG

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
RNG	0	FREQUENCY	knob					Yes
RNG	1	F. MULTIPLIER	knob					Yes
RNG	2	TRACK	switch		0: Off	1: On		No
RNG	3	HIGH CUT	knob					No
RNG	4	MIX	knob					Yes
RNG	5	Level	knob					Yes
RNG	6	Balance	knob					Yes
RNG	7	BYPASS MODE	select	0: THRU 1: MUTE FX OUT 2: MUTE OUT				Yes
RNG	8	GLOBAL MIX	switch		0: Off	1: On		No

Back to Top

LPR

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
LPR	0	MIX	knob					Yes
LPR	1	Level	knob					Yes
LPR	2	Balance	knob					Yes
LPR	3	BYPASS MODE	select	0: THRU 1: MUTE FX OUT 2: MUTE OUT				Yes
LPR	5	DUB MIX	knob					Yes
LPR	6	THRESHOLD	switch		0: Off	1: On		No
LPR	7	THRES Level	knob					No
LPR	8	MODE	select	0: MONO 1: STEREO 2: MONO UNDO 3: STEREO UNDO				No
LPR	9	QUANTIZE	select	0: OFF 1: QUARTER 2: EIGTH 3: SIXTEENTH				No
LPR	10	TRIM STOP	knob					Yes
LPR	11	TRIM START	knob					Yes
LPR	12	IMMEDIATE PLAY	switch		0: Off	1: On		No
LPR	13	RECORD BEATS	rangeKnob		0	16	1	No

Back to Top

SND

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
SND	0	Send Level	knob					No
SND	1	Out Level	knob					No

Back to Top

RTN

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
RTN	0	Mix	knob					Yes
RTN	1	Level	knob					Yes
RTN	2	Balance	knob					Yes
RTN	3	Bypass Mode	select	0: THRU 1: MUTE				Yes
RTN	4	Global Mix	switch		0: Off	1: On		No

Back to Top

MIX

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
MIX	0	Gain 1	slider					Yes
MIX	1	Gain 2	slider					Yes
MIX	2	Gain 3	slider					Yes
MIX	3	Gain 4	slider					Yes
MIX	4	Balance 1	knob					Yes
MIX	5	Balance 2	knob					Yes
MIX	6	Balance 3	knob					Yes
MIX	7	Balance 4	knob					Yes
MIX	8	Master	knob					Yes
MIX	9	Out Mode	select	0: STEREO 1: MONO				Yes

Back to Top

MBC

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
MBC	0	Freq 1	knob					No
MBC	1	Freq 2	knob					No
MBC	2	Threshold 1	knob					No
MBC	3	Ratio 1	knob					No
MBC	4	Attack 1	knob					No
MBC	5	Release 1	knob					No
MBC	6	Level 1	knob					No
MBC	7	Detect 1	select	0: RMS 1: PEAK 2: FAST RMS				No
MBC	8	Mute 1	switch		0: Off	1: On		No
MBC	9	Threshold 2	knob					No
MBC	10	Ratio 2	knob					No
MBC	11	Attack 2	knob					No
MBC	12	Release 2	knob					No
MBC	13	Level 2	knob					No
MBC	14	Detect 2	select	0: RMS 1: PEAK 2: FAST RMS				No
MBC	15	Mute 2	switch		0: Off	1: On		No
MBC	16	Threshold 3	knob					No
MBC	17	Ratio 3	knob					No
MBC	18	Attack 3	knob					No
MBC	19	Release 3	knob					No
MBC	20	Level 3	knob					No
MBC	21	Detect 3	select	0: RMS 1: PEAK 2: FAST RMS				No
MBC	22	Mute 3	switch		0: Off	1: On		No
MBC	24	Level	knob					Yes
MBC	25	Balance	knob					Yes
MBC	26	BYPASS MODE	select	0: THRU 1: MUTE				Yes

Back to Top

XVR

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
XVR	0	Freq	knob					Yes
XVR	1	Freq Multi.	select	0: X 1 1: X 10				No
XVR	2	Lo Level L	knob					No
XVR	3	Hi Level L	knob					No
XVR	4	Lo Level R	knob					No
XVR	5	Hi Level R	knob					No
XVR	6	Lo Pan L	knob					No
XVR	7	Hi Pan L	knob					No
XVR	8	Lo Pan R	knob					No
XVR	9	Hi Pan R	knob					No
XVR	11	Level	knob					Yes
XVR	12	Balance	knob					Yes
XVR	13	BYPASS MODE	select	0: THRU 1: MUTE				Yes

Back to Top

MGT

Block	ID	Name	Type	Options	Min	Max	Step	Modifier Assignable	Added
MGT	0	In Gain	knob					Yes
MGT	1	Master Level	knob					Yes
MGT	2	Time	knob					Yes
MGT