The VP4 has been added to the wiki.

Difference between revisions of "MFC-101 MIDI foot controller (legacy)"

From Fractal Audio Wiki
Jump to navigation Jump to search
(194 intermediate revisions by 3 users not shown)
Line 1: Line 1:
''The information on this page supplements the official manuals.''
+
<font color=red>The MFC-101 has been discontinued. This page will not be updated.</font>
 +
__TOC__
 +
=MFC-101 and Axe-Fx III=
 +
 
 +
The MFC-101 is a MIDI controller, with specific support for the Axe-Fx II (Axe-Fx Mode). The MFC-101's Axe-Fx mode is NOT compatible with the Axe-Fx III. However, the MFC-101 can still be used as a general MIDI foot controller with the Axe-Fx III. This requires a 5-pin MIDI cable connection. MIDI phantom power is not supported. You can use a 5-to-7 pin MIDI cable, [http://www.rocktron.com/rocktron-midi-cable-5-to-7-pin.html such as this one], to provide the MFC with power. SysEx is not supported, as documented in the [[Owners_Manuals|Guide on this page]], which means that the MFC is not able to show the tempo or the tuner.
 +
 
 +
[http://www.cabir.eu/de/content/13-mfc101-for-axefx These tutorials in English and German explain how to set up the MFC-101 with the III.]
 +
 
 +
=Pictures=
 +
 
 +
[http://forum.fractalaudio.com/threads/show-us-your-mfc-setups-post-your-pics.29984 Owners of an AX8 proudly show their rigs]
 +
 
 +
[http://3dwarehouse.sketchup.com/model.html?id=ud6398579-2d83-432c-83a0-52c17d76acda 3D image of the MFC-101]
  
 
[[image:MFC.png|link=http://www.fractalaudio.com/p-mfc-101-midi-foot-controller.php|300px]]
 
[[image:MFC.png|link=http://www.fractalaudio.com/p-mfc-101-midi-foot-controller.php|300px]]
__TOC__
 
=MFC-101: hardware=
 
  
==MFC-101: Mark I, Mark II and Mark III models==
+
=Hardware=
Mark I is the original model.
+
 
 +
==Discontinued==
 +
 
 +
The MFC-101 is no longer available from Fractal Audio. It has been replaced with the [[FC-6 and FC-12 foot controllers]].
 +
 
 +
==Mark I, Mark II and Mark III models==
 +
 
 +
'''Mark I''' — Original model.
 +
 
 +
'''Mark II'''
 +
 
 +
<blockquote>'''FRACTAL AUDIO QUOTES'''<HR>
 +
 
 +
<blockquote>
 +
[http://forum.fractalaudio.com/posts/717377]
 +
The only change is the CAT-5 connector is now an Ethercon jack. An Ethercon jack will work with either a CAT-5 cable or an Ethercon cable.
 +
</blockquote>
 +
</blockquote>
 +
 
 +
'''Mark III''' — Solid-state switch technology. No moving parts except a spring "actuator". Switching is fully electronic and silent with no switches to wear out. Mechanical lifespan is 1 million actuations. [[FASLINK]] connector. Requires separate firmware.
 +
 
 +
==Test mode==
 +
 
 +
Press Edit, followed by Reveal, to enter the hardware’s Test mode.
 +
 
 +
==Manufacturing details==
 +
 
 +
<blockquote>'''FRACTAL AUDIO QUOTES'''<HR>
  
Mark II:
+
<blockquote>The MFC-101 is fully made in China.
"The only change is the CAT-5 connector is now an Ethercon jack. An Ethercon jack will work with either a CAT-5 cable or an Ethercon cable." [http://forum.fractalaudio.com/mfc-discussion/57199-mfc-101-mkii.html#post717377 source]
 
  
Mark III has solid-State switch technology. No moving parts except a spring "actuator". Switching is fully electronic and silent with no switches to wear out. Mechanical lifespan is 1 million actuations. It provides a FASLINK connector. Separate firmware is required.
+
[http://forum.fractalaudio.com/threads/the-mfc-boots-intermittantly-without-displaying-text.144063/#post-1704810]
 +
MFCs don't have a battery.
 +
</blockquote>
 +
</blockquote>
  
==MFC-101: Test mode==
+
==Expansion port==
Press Edit followed by Reveal, to enter the hardware Test mode.
 
  
==MFC-101: manufacturing details==
+
The internal PSU for the MFC-101 will also support an expansion module for the MFC-101, but such a module has never been released.
Fractal Audio:<BR>
 
"The MFC-101 is fully made in China." [http://www.thegearpage.net/board/showpost.php?p=19557079&postcount=348 source]
 
  
==MFC-101: expansion==
+
For external control of the MFC-101, use either external switches or a MIDI switcher that sends MIDI Program Changes.
The internal PSU for the MFC-101 will also support an expansion module for the MFC-101, but such a module has never been released. [http://forum.fractalaudio.com/axe-fx-ii/35997-axe-fx-ii-technical-questions-thread-30.html#post491404 source-1] [http://forum.fractalaudio.com/axe-fx-ii/35997-axe-fx-ii-technical-questions-thread-49.html#post492331 source-2] [http://forum.fractalaudio.com/axe-fx-ii/35997-axe-fx-ii-technical-questions-thread-49.html#post492332 source-3]
 
  
For additional external control, use either external switches or a MIDI switcher that sends MIDI Program Changes.
+
==LEDs==
  
==MFC-101: LEDs==
+
With the MFC-101 in Axe-Fx Mode:
With the MFC-101 in "Axe-Fx Mode":
+
* <font color=red>Red</font> — Effect is present in the preset, bypassed.
* Red: the effect is present in the preset, bypassed.
+
*<font color=green> Green</font> — Effect is present in the preset, enabled.
* Green: the effect is present in the preset, enabled.
+
* Off — Effect is not present in the preset.
* Off: the effect is not present in the preset.
 
  
 
You can disable Red LEDs (Edit > Setup > Set IAOffLed Off), which works better for colorblind people.
 
You can disable Red LEDs (Edit > Setup > Set IAOffLed Off), which works better for colorblind people.
  
Tip: put small bits of painter's tape on top of the switch to decrease the LED brightness. [http://forum.fractalaudio.com/mfc-101-general-discussion/36965-midi-foot-controller-lights-too-bright-i-have-splendid-solution-works-perfectly.html#post504249 Or use this smart and simple solution].
+
Tip: put small bits of painter's tape on top of the switch to decrease the LED brightness.
  
=MFC-101: software=
+
=Software=
  
 
==MFC-Edit editor==
 
==MFC-Edit editor==
MFC-Edit is the official editor for the MFC-101.
+
 
 +
MFC-Edit was the official editor for the MFC-101. It has been discontinued.
  
 
* [http://www.fractalaudio.com/mfc-edit.php Get MFC-Edit]
 
* [http://www.fractalaudio.com/mfc-edit.php Get MFC-Edit]
 
* [http://forum.fractalaudio.com/forums/mfc-edit.81 MFC-Edit user forum]
 
* [http://forum.fractalaudio.com/forums/mfc-edit.81 MFC-Edit user forum]
  
[[image:Mfc-edit.png|link=|250px]]
+
[http://www.fractalaudio.com/rss/dfgherycgnmhju/MFC-Edit/Docs/MFC-Edit-Owners-Manual_8.0.pdf Owners Manual - Addendum regarding the Axe-Fx III]
 +
 
 +
[https://forum.fractalaudio.com/threads/mac-os-x-catalina-mfc-edit-wont-launch-from-desktop.155176 About MFC-Edit and Mac OS Catalina]
 +
 
 +
==Axe-Edit and MFC-101==
  
==Axe-Edit response to MFC-101==
 
 
It's recommended to not use the MFC-101 while Axe-Edit is running. It's possible to do so, but using the MFC-101 can cause audio gaps, and fast switching can cause communications issues. When Axe-Edit detects MFC-101 action, it automatically switches into Pause mode.
 
It's recommended to not use the MFC-101 while Axe-Edit is running. It's possible to do so, but using the MFC-101 can cause audio gaps, and fast switching can cause communications issues. When Axe-Edit detects MFC-101 action, it automatically switches into Pause mode.
  
Engaging and bypassing effects on the MFC-101 will not always update the visual block states in Axe-Edit. To make Axe-Edit recognise such changes, its polling mechanism must be engaged and Pausing must be disabled. This can be accomplished by attaching the Bypass parameter of any block in the preset to a controller. The block doesn't have to be connected to anything on the grid (use a low CPU block).
+
Engaging and bypassing effects on the MFC-101 will not always update the visual block states in Axe-Edit. To make Axe-Edit recognize such changes, its polling mechanism must be engaged and Pausing must be disabled. This can be accomplished by attaching the Bypass parameter of any block in the preset to a controller, so use a low CPU block. The block doesn't have to be connected to anything on the grid.
 +
 
 +
=Power and connections=
 +
 
 +
==Supply power==
 +
 
 +
You can use the supplied 9VAC adapter to power the MFC. This is the recommended way of powering the MFC-101 when upgrading the firmware.
 +
 
 +
Do NOT connect the adapter to the MFC simultaneously with Ethernet, Ethercon or an XLR cable, or when using MIDI phantom power. Damage can occur!
 +
 
 +
The Axe-Fx should be powered after the MFC-101, otherwise none of the switches may work until a preset is switched.
 +
 
 +
<blockquote>'''FRACTAL AUDIO QUOTES'''<HR>
 +
<blockquote>
 +
[https://forum.fractalaudio.com/posts/917400]
 +
This happens when the Axe-Fx II is not powered on first. Selecting any preset on the MFC will reset the state machine.
  
=MFC-101: power and connections=
+
[https://forum.fractalaudio.com/posts/688733]
 +
Do NOT attempt to extract power from the MFC connector. It is only rated for 1A and if you burn out the port we won't cover that under warranty.
 +
</blockquote>
 +
</blockquote>
  
==MFC-101: supply power==
+
[https://www.youtube.com/c/AxeFxTutorials/videos AxeFxTutorials videos]
You can use the supplied 9VAC adapter to power the MFC. This also is the recommended way of powering the MFC-101 when upgrading the firmware.
 
  
Do NOT connect the adapter to the MFC simultaneously with the use of an Ethernet, Ethercon or XLR cable, or when using MIDI phantom power. Damage can occur!
+
[http://forum.fractalaudio.com/threads/mfc-all-red-lights-on-frustrated.113858/#post-1362569 MFC-101 startup power issue when using 7-pin MIDI cables]
  
The Axe-Fx should be powered after the MFC-101, otherwise none of the switches may work until a preset is switched. Fractal Audio: "This happens when the Axe-Fx II is not powered on first. Selecting any preset on the MFC will reset the state machine." [http://forum.fractalaudio.com/axe-fx-ii-discussion/75019-axefx-ii-strange-interaction-mfc.html#post917400 source]
+
The MFC-101's power supply can NOT be used to power an FC controller.
  
Fractal Audio:<BR>
+
<blockquote>'''FRACTAL AUDIO QUOTES'''<HR>
"Do NOT attempt to extract power from the MFC connector. It is only rated for 1A and if you burn out the port we won't cover that under warranty." [http://forum.fractalaudio.com/axe-fx-ii-discussion/54261-axe-fx-rj-45-pinout.html#post688733 source]
+
<blockquote>
 +
[https://forum.fractalaudio.com/threads/help-to-find-ac-power-adapter-for-2nd-fc.148331/#post-1783280]
 +
It will NOT work. The MFC101 supply is AC, not DC.
  
[http://www.axefxtutorials.com AxeFxTutorials] has published several videos explaining how to set up the Axe-Fx II and the MFC-101 for basic use as well as how to configure expression pedals.
+
</blockquote>
 +
</blockquote>
  
[http://forum.fractalaudio.com/threads/mfc-all-red-lights-on-frustrated.113858/#post-1362569 About a MFC-101 startup power issue when using 7-pin MIDI cables]
+
==Use MIDI==
  
==MFC-101: connect through MIDI==
+
MIDI can be used for communications only (5 pins), or communications plus phantom power (7 pins). A high quality MIDI cable is required. To receive tuner and tempo data, all pins of a 5-pin MIDI cable must be connected. Many low-cost MIDI cables just have 3 pins connected and are not properly shielded, resulting in crosstalk.
MIDI can be used for communications only (5 pins), or communications plus phantom power (7 pins). A high quality MIDI cable is required. To receive tuner and tempo data all pins of a 5-pin MIDI cable must be connected. Many low-cost MIDI cables just have 3 pins connected and are not properly shielded, resulting in crosstalk.
 
  
 
To use phantom power via MIDI, a 7-pin MIDI cable is required. All pins must be wired (pins 6 and 7 carry power). Connect the 9VAC adapter to the phantom power input at the rear of the Axe-Fx (the Axe-Fx II doesn't provide power itself, it needs the power supply).
 
To use phantom power via MIDI, a 7-pin MIDI cable is required. All pins must be wired (pins 6 and 7 carry power). Connect the 9VAC adapter to the phantom power input at the rear of the Axe-Fx (the Axe-Fx II doesn't provide power itself, it needs the power supply).
  
The connection method must be specified in the I/O menu and in the configuration of the MFC-101.
+
The connection method must be specified in the [[I/O menu]] and in the configuration of the MFC-101.
 +
 
 +
==Use Ethernet or Ethercon==
  
==MFC-101: connect through Ethernet or Ethercon==
+
A CAT5 Ethernet cable can be used for communications and power, instead of MIDI. It provides power from the Axe-Fx II to the MFC-101 without requiring connecting the power supply to the Axe-Fx II, transmits MIDI data and tuner and tempo information, and switches off the MFC-101 automatically when the Axe-Fx II is turned off.
A CAT5 Ethernet cable can be used for communications and power instead of MIDI. It provides power to the MFC-101 without requiring the power supply into the Axe-Fx, transmits MIDI data and tuner and tempo information, and switches off the MFC-101 automatically when the Axe-Fx II is turned off.
 
  
 
Mark II and III models also support Ethercon which is sturdier than Ethernet.
 
Mark II and III models also support Ethercon which is sturdier than Ethernet.
  
When using Ethernet/Ethercon, the MFC's MIDI OUT port won't pass data anymore. You can't use both ports simultaneously. [http://forum.fractalaudio.com/mfc-discussion/44511-there-pass-midi-thru-midi-foot-controller-while-expansion-cat-5-mode.html#post587648 source]
+
When using Ethernet/Ethercon, the MFC's MIDI OUT port won't pass data anymore. You can't use both ports simultaneously.  
 
 
 
The connection method must be specified in the I/O menu and in the configuration of the MFC-101.
 
The connection method must be specified in the I/O menu and in the configuration of the MFC-101.
  
 
Note that a MIDI interface is still required to perform firmware updates.
 
Note that a MIDI interface is still required to perform firmware updates.
  
==MFC-101: connect through FASLINK==
+
==Use FASLINK==
The 3rd and best way to connect and power the MFC-101 is through FASLINK. This is supported by the Mark III model and the Axe-Fx II XL and XL+. A regular XLR (microphone) cable powers the MFC and transfers data. A power supply into the Axe-Fx is not required.
+
 
 +
The 3rd and best way to connect and power the MFC-101 is through [[FASLINK]]. This is supported by the Mark III model and the Axe-Fx II XL and XL+. A regular XLR (microphone) cable powers the MFC and transfers data. Connecting the power supply to the Axe-Fx II is not required.
  
 
The connection method must be specified in the I/O menu and in the configuration of the MFC-101.
 
The connection method must be specified in the I/O menu and in the configuration of the MFC-101.
  
[[FASLINK|More about FASLINK.]]
+
Read this: [[FASLINK]]
  
 
Note that a MIDI interface is still required to perform firmware updates.
 
Note that a MIDI interface is still required to perform firmware updates.
  
==MFC-101: use two MFC-101s?==
+
==Two MFC-101s==
Fractal Audio:<BR>
 
"True Master Slave is not possible. Split merge works in theory, but there can be hiccups. One MFC can respond to program changes from another, but the two units won't appear to be in any kind of sync". [http://forum.fractalaudio.com/mfc-discussion/100431-can-you-use-another-mfc-control-mfc.html#post1204154 source]
 
  
=MFC-101: system configuration=
+
<blockquote>'''FRACTAL AUDIO QUOTES'''<HR></blockquote>
 +
<blockquote>
 +
[http://forum.fractalaudio.com/posts/1204154]
 +
True Master Slave is not possible. Split merge works in theory, but there can be hiccups. One MFC can respond to program changes from another, but the two units won't appear to be in any kind of sync.
 +
</blockquote>
 +
</blockquote>
  
==MFC-101: initial configuration==
+
=System configuration=
[http://www.fractalaudio.com/support.php#manuals Read the Quick Start Guide]
+
 
 +
==Initial configuration==
 +
 
 +
[[Owners_Manuals|Read the Quick Start Guide.]]
  
 
Basics:
 
Basics:
Line 109: Line 173:
 
# Use Edit > Midi to configure the IA switches.
 
# Use Edit > Midi to configure the IA switches.
  
Tutorials on G66 site:
+
[http://www.g66.eu G66 provides several tutorials.]
* [http://www.g66.eu/nl/products/mission 1]
+
 
* [http://www.g66.eu/nl/support/fractal-audio-support 2]
+
==Firmware updates==
  
==MFC-101: firmware updates==
 
 
Go through Edit > Setup to see the currently loaded firmware version.
 
Go through Edit > Setup to see the currently loaded firmware version.
  
All firmware release notes can be found here: [[Firmware release notes: MFC-101]].
+
All firmware release notes can be found here: [[Firmware release notes - MFC-101]]
  
[http://www.fractalaudio.com/support-fractal.html Download the latest MFC-101 firmware], launch Fractal-Bot and follow the instructions. Note that there are different firmware files for the various hardware models.
+
[https://www.fractalaudio.com/mfc-downloads/ Download the latest MFC-101 firmware], launch [[Fractal-Bot]] and follow the instructions. Note that there are different firmware files for the various hardware models.
  
 
The update process requires a MIDI interface. Updating is not possible via Ethernet/Ethercon or FASLINK. During the update process, the MFC-101 cannot be powered via MIDI phantom power. The firmware file includes a Read Me - Firmware Update Guide, explaining the process. It also decribes how to configure the Axe-Fx II as a MIDI interface, and how to power the MFC-101 via Ethernet/Ethercon during updating if you haven't got the power supply.
 
The update process requires a MIDI interface. Updating is not possible via Ethernet/Ethercon or FASLINK. During the update process, the MFC-101 cannot be powered via MIDI phantom power. The firmware file includes a Read Me - Firmware Update Guide, explaining the process. It also decribes how to configure the Axe-Fx II as a MIDI interface, and how to power the MFC-101 via Ethernet/Ethercon during updating if you haven't got the power supply.
Line 127: Line 190:
  
 
Error messages during updating:
 
Error messages during updating:
* Error 14: rare problem that occurs after a failed firmware update. Once this occurs, you can start over to achieve success, but the MFC-101 will “time out” if the update is not completed quickly enough, causing the unit to display ERROR 14 again. Decrease the MIDI Buffer Delay setting in Fractal-Bot (in step 1 “READY”) to 90ms or lower to speed the firmware transmission process. Alternatively, try to slow things down by increasing buffer delay to, say, 400.  
+
* '''Error 14''' — rare problem that occurs after a failed firmware update. Once this occurs, you can start over to achieve success, but the MFC-101 will “time out” if the update is not completed quickly enough, causing the unit to display ERROR 14 again. Decrease the MIDI Buffer Delay setting in Fractal-Bot (in step 1 “READY”) to 90ms or lower to speed the firmware transmission process. Alternatively, try to slow things down by increasing buffer delay to, say, 400.  
* Error 16: usually indicates that the MFC saw “garbage” during a firmware update. This problem is often seen when using “inferior” MIDI Interfaces, but can also indicate computer problems, or even a bad MIDI cable. In rare cases, re-downloading the firmware update can also solve this problem.
+
* '''Error 16''' — usually indicates that the MFC saw “garbage” during a firmware update. This problem is often seen when using “inferior” MIDI Interfaces, but can also indicate computer problems, or even a bad MIDI cable. In rare cases, re-downloading the firmware update can also solve this problem.
* Error 18: indicates that the MFC-101 has received some stray MIDI message while awaiting a firmware update. Please make sure no other MIDI applications are running on your computer, or, if using the Axe-Fx II as a MIDI Interface, ensure that I/O: MIDI: SEND REALTIME SYSEX is set to “NONE”.
+
* '''Error 18''' — indicates that the MFC-101 has received some stray MIDI message while awaiting a firmware update. Please make sure no other MIDI applications are running on your computer, or, if using the Axe-Fx II as a MIDI Interface, ensure that I/O: MIDI: SEND REALTIME SYSEX is set to “NONE”.
* The manual lists and explains other error messages.
 
  
==MFC-101: backup and restore==
+
The manual lists and explains other error messages.
Use Edit > Setup > Sysex Data, when using a MIDI librarian. Or use Fractal-Bot of MFC-Edit.
+
 
 +
==Backup and restore==
 +
 
 +
Use Edit > Setup > Sysex Data, when using a MIDI librarian. Or use [[Fractal-Bot]] of MFC-Edit.
 +
 
 +
==Restore factory defaults==
  
==MFC-101: restore factory defaults==
 
 
Power the MFC-101 while holding switch 11.
 
Power the MFC-101 while holding switch 11.
  
 
The manual lists all factory default settings.
 
The manual lists all factory default settings.
  
==MFC-101: TotalSync==
+
==TotalSync==
 +
 
 
When you switch presets or engage/bypass effects on the front panel of the Axe-Fx II or in Axe-Edit, the MFC-101 can switch along. It's called TotalSync which can be enabled and disabled in the MFC's MIDI menu.
 
When you switch presets or engage/bypass effects on the front panel of the Axe-Fx II or in Axe-Edit, the MFC-101 can switch along. It's called TotalSync which can be enabled and disabled in the MFC's MIDI menu.
  
 
TotalSync doesn't work in Song and Set modes, and custom MFC-101 Tx Map and Axe-Fx II preset remapping (for example to support scenes) are not supported.
 
TotalSync doesn't work in Song and Set modes, and custom MFC-101 Tx Map and Axe-Fx II preset remapping (for example to support scenes) are not supported.
  
==MFC-101: MIDI channel(s)==
+
==MIDI channel(s)==
 +
 
 
By default the MFC-101 sends MIDI Program Changes on all MIDI channels, regardless of the selected MIDI channel on which the MFC-101 operates.
 
By default the MFC-101 sends MIDI Program Changes on all MIDI channels, regardless of the selected MIDI channel on which the MFC-101 operates.
  
To disable this behavior ([http://forum.fractalaudio.com/mfc-discussion/87571-mfc-sends-cc-0-midi-channel-2-preset-change.html#post1061520 source]):
+
To disable this behavior: [http://forum.fractalaudio.com/mfc-discussion/87571-mfc-sends-cc-0-midi-channel-2-preset-change.html#post1061520]
 
# Optionally reset the MFC-101 to FACTORY settings if you also want to do the step noted in "PS".
 
# Optionally reset the MFC-101 to FACTORY settings if you also want to do the step noted in "PS".
 
# Temporarily set BANK SIZE to 17.
 
# Temporarily set BANK SIZE to 17.
Line 163: Line 231:
 
# Enable Receive Program Changes in Edit > System.
 
# Enable Receive Program Changes in Edit > System.
  
==MFC-101: tuner and tap tempo==
+
==Tuner and tap tempo==
 +
 
 
To show the Tuner display and see the Tempo LED blink in the correct tempo on the MFC-101, the MFC-101 must be in Axe-Fx Mode. Also, a connection type must be used which supports 5-pin MIDI, CAT5 (Ethernet/Ethercon) or FASLINK. On the Axe-Fx II (I/O > MIDI) Send Realtime Sysex must be set to: Tuner, Tempo, or All.
 
To show the Tuner display and see the Tempo LED blink in the correct tempo on the MFC-101, the MFC-101 must be in Axe-Fx Mode. Also, a connection type must be used which supports 5-pin MIDI, CAT5 (Ethernet/Ethercon) or FASLINK. On the Axe-Fx II (I/O > MIDI) Send Realtime Sysex must be set to: Tuner, Tempo, or All.
  
Line 173: Line 242:
  
 
You can combine Tap Tempo and Tuner functionality: hold Tap Tempo will enter the Tuner mode. Use Edit > Setup to set this up. This does not work with external switches.
 
You can combine Tap Tempo and Tuner functionality: hold Tap Tempo will enter the Tuner mode. Use Edit > Setup to set this up. This does not work with external switches.
 
[http://wiki.fractalaudio.com/axefx2/index.php?title=Tuner#Creating_a_Tuner_Preset How to create a tuner "preset" instead of an IA switch]
 
  
 
To use an external switch to control Tap Tempo:
 
To use an external switch to control Tap Tempo:
Line 182: Line 249:
 
# In Edit > MIDI > XS set the switch to TypTOG.
 
# In Edit > MIDI > XS set the switch to TypTOG.
  
=MFC-101: presets, scenes, songs and setlists=
+
=Presets, scenes, songs, setlists=
 +
 
 +
==Access presets 384 and up==
 +
 
 +
The Axe-Fx II XL and XL+ provide more than 384 presets. To access these with the MFC-101, MIDI mapping (transmit table) must be used, either on the MFC or Axe-Fx. [http://forum.fractalaudio.com/threads/access-presets-between-384-and-999-with-mfc-101.107452/ Here's how]
 +
 
 +
<blockquote>'''FRACTAL AUDIO QUOTES'''<HR>
  
==MFC-101: access presets 384 and up==
+
<blockquote>
Fractal Audio:<BR>
+
[https://forum.fractalaudio.com/posts/1034747]
"The MFC-101 stores 384 presets. The Axe-Fx II Mark I/II also store 384 presets. Many MIDI controllers only store 128 presets. There is no correlation between the number of presets on a MIDI controller and the device being controlled. This is not a bug, mistake or deception." [http://forum.fractalaudio.com/mfc-discussion/84702-accessing-bank-d-xl-mfc-101-mk1.html#post1034747 source]
+
The MFC-101 stores 384 presets. The Axe-Fx II Mark I/II also store 384 presets. Many MIDI controllers only store 128 presets. There is no correlation between the number of presets on a MIDI controller and the device being controlled.
 +
</blockquote>
 +
</blockquote>
  
The Axe-Fx II XL and XL+ provide more than 384 presets. To access these with the MFC-101, MIDI mapping (transmit table) must be used. [http://forum.fractalaudio.com/threads/access-presets-between-384-and-999-with-mfc-101.107452/ Here's how]
+
==Number of presets per bank, number of IA switches==
  
==MFC-101: number of presets per bank, number of IA switches==
 
 
The MFC-101 defaults to 5 presets per bank. It can be set to any number. Use Edit > Setup > Bank Size to change this, depending on how many IA switches you want to be accessible directly without needing to press Reveal.
 
The MFC-101 defaults to 5 presets per bank. It can be set to any number. Use Edit > Setup > Bank Size to change this, depending on how many IA switches you want to be accessible directly without needing to press Reveal.
  
Line 198: Line 272:
 
Bank Size also influences Song and Set Mode.
 
Bank Size also influences Song and Set Mode.
  
Preset switches start from the bottom row by default. You can change this using the parameter FirstPresetSwitch. This lets you specify where the presets start on the board. Preceding switches automatically are IA switches.
+
Preset switches start from the bottom row by default. You can change this using the parameter FirstPresetSwitch. This lets you specify where the presets start on the board (preceding switches automatically are IA switches). Note that the FirstPresetSwitch parameter is not supported on the Mark I and II models.
  
 
The MFC-101 doen't support preset switching by entering the number of a preset.
 
The MFC-101 doen't support preset switching by entering the number of a preset.
  
==MFC-101: Bank Style parameter==
+
==Bank Style parameter==
 +
 
 
Use Edit > Setup > Bank Style to tell the MFC-101 what to do when changing banks:
 
Use Edit > Setup > Bank Style to tell the MFC-101 what to do when changing banks:
 +
 
* automatically load the first preset of the bank
 
* automatically load the first preset of the bank
 
* automatically load the preset at the current position in the bank (default)
 
* automatically load the preset at the current position in the bank (default)
* nothing.
+
* nothing
  
When set to None, banking up/down will show the bank number and the preset range within the bank (Smart Banks feature).
+
When set to NONE, banking up/down will show the bank number and the preset range within the bank (Smart Banks feature).
  
 
The speed of scrolling through Banks, Songs and Sets cannot be adjusted.
 
The speed of scrolling through Banks, Songs and Sets cannot be adjusted.
Line 214: Line 290:
 
When using Bank Size "0", use the Up/Down switches to scroll through banks and automatically load the "Autoload" preset.
 
When using Bank Size "0", use the Up/Down switches to scroll through banks and automatically load the "Autoload" preset.
  
==MFC-101: Bank/Song Limit and Bank/Song Wrap parameters==
+
==Bank/Song Limit and Bank/Song Wrap parameters==
 +
 
 
You may need access to just a subset of all available banks on the MFC-101. The Bank/Song Limit parameter lets you define the range of this subset. This prevents having to scroll through banks/songs you don't need.
 
You may need access to just a subset of all available banks on the MFC-101. The Bank/Song Limit parameter lets you define the range of this subset. This prevents having to scroll through banks/songs you don't need.
  
 
Also, you may want to stop scrolling through banks/songs after reaching the first or last bank/song (no wrapping around). The Bank/Song Wrap parameter lets you enable/disable this.
 
Also, you may want to stop scrolling through banks/songs after reaching the first or last bank/song (no wrapping around). The Bank/Song Wrap parameter lets you enable/disable this.
  
==MFC-101: Global Preset==
+
==Global Preset==
 +
 
 
Set Global Preset to ON (off by default) in Edit > Setup and select the preset that you want to have as a global preset.
 
Set Global Preset to ON (off by default) in Edit > Setup and select the preset that you want to have as a global preset.
  
Line 228: Line 306:
 
Turn off Global Preset if you want to be able to recall a preset in its saved state by pressing a preset switch a second time (see: Panic switch).
 
Turn off Global Preset if you want to be able to recall a preset in its saved state by pressing a preset switch a second time (see: Panic switch).
  
==MFC-101: Alternate Presets==
+
Read this: [https://forum.fractalaudio.com/threads/wicked-wiki-8-pressing-a-mfc-101-preset-switch-twice.49374/ Wicked Wiki article]
 +
 
 +
==Alternate Presets==
 +
 
 
Pressing a preset switch a second time lets you activate another preset, which can be different per preset. This is an alternative to using a Global Preset (see above) or Backtracking (see below). Set this in the Preset menu on the MFC-101. Note that the "alternate preset" is a MIDI Program Change, not a "preset switch" as configured on the MFC.
 
Pressing a preset switch a second time lets you activate another preset, which can be different per preset. This is an alternative to using a Global Preset (see above) or Backtracking (see below). Set this in the Preset menu on the MFC-101. Note that the "alternate preset" is a MIDI Program Change, not a "preset switch" as configured on the MFC.
  
[http://forum.fractalaudio.com/mfc-discussion/49374-wicked-wiki-8-pressing-midi-foot-controller-101-preset-switch-twice.html More information]
+
Read this: [https://forum.fractalaudio.com/threads/wicked-wiki-8-pressing-a-mfc-101-preset-switch-twice.49374/ Wicked Wiki article]
  
 
You use Alternate Preset in combination with scenes on the Axe-Fx by mapping presets to scenes on the Axe-Fx II.
 
You use Alternate Preset in combination with scenes on the Axe-Fx by mapping presets to scenes on the Axe-Fx II.
  
==MFC-101: Backtracking==
+
==Backtracking==
 +
 
 
Backtracking means that a pressing a preset switch a second time will recall the previous preset. Set this per preset (Edit > Preset) or configure Global Preset to act as Backtrack ("BAK"). Backtracking always recalls scene 1.
 
Backtracking means that a pressing a preset switch a second time will recall the previous preset. Set this per preset (Edit > Preset) or configure Global Preset to act as Backtrack ("BAK"). Backtracking always recalls scene 1.
  
Read this: [http://forum.fractalaudio.com/mfc-discussion/49374-wicked-wiki-8-pressing-midi-foot-controller-101-preset-switch-twice.html Wicked Wiki]
+
Read this: [https://forum.fractalaudio.com/threads/wicked-wiki-8-pressing-a-mfc-101-preset-switch-twice.49374/ Wicked Wiki article]
 +
 
 +
==Scene switching==
  
==MFC-101: switch scenes==
 
 
The MFC-101 offers special support scenes:
 
The MFC-101 offers special support scenes:
 +
 
* recall any of the 8 scenes directly
 
* recall any of the 8 scenes directly
 
* increment or decrement scenes
 
* increment or decrement scenes
* toggle between scenes 1 and 2.
+
* toggle between scenes 1 and 2
  
 
You can also use general MIDI commands to switch scenes, or use external momentary switches.
 
You can also use general MIDI commands to switch scenes, or use external momentary switches.
  
Use I/O > Midi > Mapping on the Axe-Fx II if you want preset switches to switch to specific scenes. For example, if you want the first 5 preset switches on the MFC to switch to preset 000, scenes 1-5, use Mapping.
+
Use Mapping in the [[MIDI/Remote menu]] on the Axe-Fx II if you want preset switches to switch to specific scenes. For example, if you want the first 5 preset switches on the MFC to switch to preset 000, scenes 1-5, use Mapping.
 +
 
 +
The parameter [[Scenes#Scene_Revert|Scene Revert]] determines what happens with effect states when switching scenes with a MIDI controller.
  
The parameter Scene Revert on the Axe-Fx II determines what happens with effect states when switching scenes with a MIDI controller.
+
==Songs and sets==
  
==MFC-101: songs and sets==
 
 
Song and Set names on the MFC start with a "S". You can assign up to 15 presets per song, depending on the Bank Size setting. The MFC supports up to 100 songs. Preset switches in Songs can be set to OFF.
 
Song and Set names on the MFC start with a "S". You can assign up to 15 presets per song, depending on the Bank Size setting. The MFC supports up to 100 songs. Preset switches in Songs can be set to OFF.
  
Line 261: Line 346:
 
You cannot set scenes. A preset in a song will always load scene 1.  
 
You cannot set scenes. A preset in a song will always load scene 1.  
  
An alternative to Song Mode: use [[Scenes]].
+
An alternative to Song Mode: [[Scenes]]
  
=MFC-101: Instant Access switches=
+
=Instant Access switches=
 +
 
 +
==Axe-Fx Mode (slave) or non-Axe-Fx Mode (master) ==
  
==MFC-101: Axe-Fx Mode (slave) or non-Axe-Fx Mode (master) ==
 
 
When the MFC-101 runs in Axe-Fx Mode, the IA effect switches, adhere to their state in the currently loaded preset on the Axe-Fx II. So the Axe-Fx II is master and the MFC-101 is slave.
 
When the MFC-101 runs in Axe-Fx Mode, the IA effect switches, adhere to their state in the currently loaded preset on the Axe-Fx II. So the Axe-Fx II is master and the MFC-101 is slave.
  
 
Vice versa, when the MFC-101 does not run in Axe-Fx Mode, the MFC-101 determines the state of the switch and effect. In non-Axe-Fx mode, Tuner and Tap Tempo are not displayed on the MFC-101.
 
Vice versa, when the MFC-101 does not run in Axe-Fx Mode, the MFC-101 determines the state of the switch and effect. In non-Axe-Fx mode, Tuner and Tap Tempo are not displayed on the MFC-101.
  
==MFC-101: configure instant access switches==
+
==Configure IA switches==
 +
 
 
Any switch can operate as a toggle (latching) or as a momentary switch, and can be given a 7-character name (Edit > Setup).
 
Any switch can operate as a toggle (latching) or as a momentary switch, and can be given a 7-character name (Edit > Setup).
  
 
IA switches can be assigned to specific Axe-Fx II functions (selected from a list) or configured to perform MIDI functionality.
 
IA switches can be assigned to specific Axe-Fx II functions (selected from a list) or configured to perform MIDI functionality.
  
In Axe-Fx Mode go to Edit > Midi > IA and select the desired block for each switch from the list of effects. In Axe-Fx Mode the IA switches operate globally, meaning that you cannot change switch assignments per preset.
+
In Axe-Fx Mode, go to Edit > Midi > IA and select the desired block for each switch from the list of effects. In Axe-Fx Mode, the IA switches operate globally, meaning that you cannot change switch assignments per preset.
  
When you've assigned an effect to a switch, it enables or bypasses that effect. You can also assign the switch to X/Y, to switch an effect between X and Y. Other available Axe-Fx functions include Vol Inc, Vol Dec and scenes.  
+
When you've assigned an effect to a switch, it enables or bypasses that effect. You can also assign the switch to X/Y, to switch an effect between X and Y. Other available Axe-Fx functions include Vol Inc, Vol Dec and Scenes.  
  
 
If you select "None", the switch is not assigned to specific Axe-Fx functionality. It will be available for general MIDI use (referred to as: General Use IA Switch). This lets you program MIDI commands. You can send 2 separate MIDI CCs, a MIDI PC and additional custom MIDI commands per switch. Use value 127 to switch on effects, 0 to switch off. Or select OFF to send nothing at all. General Use IAs operate globally (same across all presets).
 
If you select "None", the switch is not assigned to specific Axe-Fx functionality. It will be available for general MIDI use (referred to as: General Use IA Switch). This lets you program MIDI commands. You can send 2 separate MIDI CCs, a MIDI PC and additional custom MIDI commands per switch. Use value 127 to switch on effects, 0 to switch off. Or select OFF to send nothing at all. General Use IAs operate globally (same across all presets).
Line 283: Line 370:
 
If Axe-Fx Mode is disabled, the MFC-101 turns into a "master" device and determines which effect in a preset is engaged or bypassed (Edit > Preset). In this case preset names in Preset Mode are preced by a "P" (instead of "X").
 
If Axe-Fx Mode is disabled, the MFC-101 turns into a "master" device and determines which effect in a preset is engaged or bypassed (Edit > Preset). In this case preset names in Preset Mode are preced by a "P" (instead of "X").
  
==MFC-101: keep IA switch states when switching presets==
+
==Keep IA switch states when switching presets==
You may want "general MIDI function" IAs to carry over their active state when switching presets. This is controlled through the Global and Send w/Preset parameters. Global defaults to Off, and Send w/Preset defaults to On. See the table in the Owner's Manual for a description of these parameters.
+
 
 +
You may want "general MIDI function" IAs to carry over their active state when switching presets. This is controlled through the Global and Send w/Preset parameters. Global defaults to Off, and Send w/Preset defaults to On. See the table in the [[Owners_Manuals|Owner's Manual]] for a description of these parameters.
 +
 
 +
==Grouped switches (switch linking)==
  
==MFC-101: grouped switches (switch linking)==
 
 
The Switch Links setting lets you define a group of switches. Within that group only one setting can be active, so selecting one switch will automatically disable the others within the group (they're mutually exclusive). There's a maximum of two groups and 5 switches per group. Switch Links is particularly useful to switch channels on an external amp which supports MIDI.
 
The Switch Links setting lets you define a group of switches. Within that group only one setting can be active, so selecting one switch will automatically disable the others within the group (they're mutually exclusive). There's a maximum of two groups and 5 switches per group. Switch Links is particularly useful to switch channels on an external amp which supports MIDI.
  
==MFC-101: methods to switch between amp tones==
+
==Turn an IA switch into a preset switch==
Some ideas:
 
* Use a single Amp block and scene controllers to switch using scenes.
 
* Use a single Amp block and X/Y, with a dedicated Amp X/Y switch, or scenes.
 
* Use two Amp blocks with their bypass parameters attached to an external controller, and a switch assigned to the external controller.
 
* Use two Amp blocks with a Mixer block set to "morph", attached to an external controller, and a switch.
 
* Use two Amp blocks and scenes, and dedicated scene switches.
 
* Use two Amp blocks, with dedicated AMP 1 and AMP 2 switches and Switch Linking.
 
* Assign an external controller to Boost or Input Trim in the Amp block, and assign an IA switch to the external controller.
 
  
==MFC-101: turn an IA switch into a preset switch==
+
# Set the switch function to None (Edit > MIDI).
# Set the switch function to None (Edit > MIDI)
+
# Scroll to the PC page, set it to On and specify the Program Change number.
# Scroll to the PC page, set it to On and specify the Program Change number
 
 
# Set the Switch Type (Edit > Setup) to Momentary, for correct LED behavior.
 
# Set the Switch Type (Edit > Setup) to Momentary, for correct LED behavior.
  
Line 308: Line 388:
 
This is a great alternative to the Global Preset feature.
 
This is a great alternative to the Global Preset feature.
  
==MFC-101: engage/bypass multiple effects at once==
+
==Engage/bypass multiple effects at once==
Here's a trick that lets you assign multiple effects to one switch. Source: M@.
+
 
 +
Here's a trick that lets you assign multiple effects to one switch (source: Admin M@).
  
 
# Pick a (low CPU) surrogate such as VOLx or FILTERx, set to NULL. On the Axe-Fx II, go to I/O > CTRL and assign the same MIDI CC to your surrogate and all of the effects you want assign across the single footswitch.
 
# Pick a (low CPU) surrogate such as VOLx or FILTERx, set to NULL. On the Axe-Fx II, go to I/O > CTRL and assign the same MIDI CC to your surrogate and all of the effects you want assign across the single footswitch.
Line 319: Line 400:
 
Alternatively: assign the same CC (or an external controller) to all desired effects. But you won't get multi-color LEDs.
 
Alternatively: assign the same CC (or an external controller) to all desired effects. But you won't get multi-color LEDs.
  
==MFC-101: use a single IA switch to toggle between two effects==
+
==Use a single IA switch to toggle between two effects==
 +
 
 
Set up the switch to send a CC to an external controller. Assign Bypass in two effect blocks to the same controller. Set the Start value of one block to 100 and the other to 0.
 
Set up the switch to send a CC to an external controller. Assign Bypass in two effect blocks to the same controller. Set the Start value of one block to 100 and the other to 0.
  
An example when alternating between Comp and Drive: set one of the externals to the same CC as COMP, then use it to bypass Drive. Set the switch to COMP and you'll get RED=DRIVE, GREEN=COMPRESSOR (source: Matman).
+
An example when alternating between Comp and Drive: set one of the externals to the same CC as COMP, then use it to bypass Drive. Set the switch to COMP and you'll get RED=DRIVE, GREEN=COMPRESSOR.
 
 
[http://forum.fractalaudio.com/mfc-discussion/70746-how-use-one-ia-switch-turn-one-effect-another-off-simultaneously.html More methods]
 
  
==MFC-101: use a single switch to enable some effects and bypass others==
+
==Switch between two effect speeds==
[http://forum.fractalaudio.com/mfc-discussion/39864-1-step-3-ia-actions-possible.html#post539974 Explanation]
 
  
==MFC-101: switch between two effect speeds==
 
 
You can use a switch to change speeds (tremolo, vibe, phaser etc.):
 
You can use a switch to change speeds (tremolo, vibe, phaser etc.):
 
# Assign an external controller to the effect's Rate parameter.
 
# Assign an external controller to the effect's Rate parameter.
Line 335: Line 413:
 
# On the MFC assign a switch to the controller's MIDI CC.
 
# On the MFC assign a switch to the controller's MIDI CC.
  
To force a gradual change between the two settings, increase Damp in the modifier menu of the effect parameter on the Axe-Fx.
+
To force a gradual change between the two settings, increase Damping in the modifier menu of the effect parameter on the Axe-Fx.
 +
 
 +
==Switch for leads==
  
==MFC-101: configure a switch for leads==
+
* Use a dedicated preset.
* If you have a single solo preset, use Global Preset (press any preset twice to recall the solo preset).
+
* Configure a Global Preset (press any preset twice to recall the solo preset).
 
* If you have various solo presets, use the Alternate Preset feature (press a preset switch twice to recall an "alternate" preset for that switch).
 
* If you have various solo presets, use the Alternate Preset feature (press a preset switch twice to recall an "alternate" preset for that switch).
 
* If you use Song Mode, create solo presets and assign them to songs.
 
* If you use Song Mode, create solo presets and assign them to songs.
 
* If you prefer IAs, configure a switch to change the state of two effects at once. If two effects is not enough, you can use custom MIDI to configure more. Or assign a single CC to multiple effects on the Axe-Fx II (I/O > Ctrl), and change them all in one go with a single switch.
 
* If you prefer IAs, configure a switch to change the state of two effects at once. If two effects is not enough, you can use custom MIDI to configure more. Or assign a single CC to multiple effects on the Axe-Fx II (I/O > Ctrl), and change them all in one go with a single switch.
* Connect an IA switch to. preset switch.
 
 
* Use [[Scenes]].
 
* Use [[Scenes]].
  
==MFC-101: configure a panic switch==
+
==Panic switch==
At times it's handy to quickly recall the current scene in its saved state (revert), just by pressing the current scene switch a second time. This will reset any changed IAs to their save state for this scene. This requires that Scene Revert (I/O > MIDI) is set to ON.
+
 
 +
At times it's handy to quickly recall the current scene in its saved state (revert), just by pressing the current scene switch a second time. This will reset any changed IAs to their save state for this scene. This requires that [[MIDI#Scene_Revert|Scene Revert]] is set to ON.
  
Alternatively you can also press the preset switch (the current one) again. This loads scene 1 of the current preset in its saved state. This requires that Global Preset is not enabled. Set Ignore Redundant PC (Axe-Fx) to Off to prevent audio gaps.
+
Alternatively you can also press the preset switch (the current one) again. This loads scene 1 of the current preset in its saved state. This requires that Global Preset is not enabled. Set [[MIDI#Ignore_Redundant_PC|Ignore Redundant PC]] to Off to prevent audio gaps.
  
=MFC-101: expression pedals=
+
=Expression pedals=
 +
 
 +
==Connect and calibrate an expression pedal==
  
==MFC-101: connect and calibrate an expression pedal==
 
 
You can connect up to 4 expression pedal(s) to the rear of the MFC-101. Expression pedals need 1/4" TRS (stereo) cables.
 
You can connect up to 4 expression pedal(s) to the rear of the MFC-101. Expression pedals need 1/4" TRS (stereo) cables.
  
 
Use Edit > Setup and Edit > MIDI to configure the pedals. Edit > Preset lets you override global expression pedal settings.
 
Use Edit > Setup and Edit > MIDI to configure the pedals. Edit > Preset lets you override global expression pedal settings.
 +
 +
Note that the PEDAL menu on the Axe-Fx II is not used when configuring pedals which are connected to the MFC-101.
  
 
By default pedal #1 is mapped to CC 11 (global Output 1 volume) and pedal #2 to CC 16 (External 1). Pedals 3 and 4 default to OFF, which may not be obvious because the MFC will let you calibrate the pedals.
 
By default pedal #1 is mapped to CC 11 (global Output 1 volume) and pedal #2 to CC 16 (External 1). Pedals 3 and 4 default to OFF, which may not be obvious because the MFC will let you calibrate the pedals.
  
Calibration of pedals: read chapter 7 of the manual. Note that it's normal for pedals not to employ the full value range (0 - 127). If your pedal only gets to 100 or so, it can still perform 100%. Note: after calibration you can check if the pedal goes from 0 to 127 by entering the MFC's test mode (see above). Near the end of the test you can test the pedals.
+
Calibration of pedals: read chapter 7 of the MFC-101 manual. Note that it's normal for pedals to not employ the full value range (0 - 127). If your pedal only gets to 100 or so, it can still perform 100%. Near the end of the test you can test the pedals. Note: after calibration you can check if the pedal goes from 0 to 127 by entering the MFC's test mode (see above).
  
 
Use the Beginning Value parameter (Edit > Midi) to define the state of the pedal after switching presets. "PDL" means that the position of the pedal is polled and recalled, "Off" means that the pedal is off until moved (default), or you can select a specific value between 0 and 127.
 
Use the Beginning Value parameter (Edit > Midi) to define the state of the pedal after switching presets. "PDL" means that the position of the pedal is polled and recalled, "Off" means that the pedal is off until moved (default), or you can select a specific value between 0 and 127.
 +
 +
The modifier menu on the Axe-Fx II allows further control of parameters.
  
 
While you can define/limit the operational range of an expression pedal (globally or per preset), you also use the Modifier menu of effects blocks on the Axe-Fx II for this purpose.
 
While you can define/limit the operational range of an expression pedal (globally or per preset), you also use the Modifier menu of effects blocks on the Axe-Fx II for this purpose.
  
Settings in Edit > MIDI are global. If you want program a pedal to behave differently in specific presets, adjust in Edit > Preset.
+
Settings in Edit > MIDI are global. If you want to program a pedal to behave differently in specific presets, adjust the settings in Edit > Preset.
  
==MFC-101: make a pedal control different effects wth a pedal==
+
==Connect an expression pedal with a built-in switch==
Method 1 (i.e. using a single pedal control either Wah or Whammy):
 
# Insert a Wah block.
 
# Insert a Pitch block, directly above or below the Wah in a parallel row. Connect it back to to the main row.
 
# In the Modifier menu of BOTH effects (Wah: Frequency; Pitch: Control): set Source to External 1. Enable Auto-engage.
 
# Add a Mixer block to the main row, just after Wah and Pitch.
 
# Edit Mixer: enter the Modifier menu of the Gain parameter for the row that connects to the Wah. Set Source to another external controller (which will be attached to an IA-switch to switch between Wah and Whammy). Set Start Value to 100% and End Value to 0.
 
# Do the same for the row that connects to the Pitch block. But: set Start Value to 0% and End Value to 100%.
 
# Program an IA-switch on the MFC to switch between Wah and Whammy, using the Mixer rows. Use the CC of the external controller that you specified while editing the Mixer block, and send "127" for the Wah, and "0" for the Whammy.
 
# That's all. Moving the pedal should activate both the Wah and the Pitch block. But thanks to the Mixer block you'll only hear one of these effects. If you're hearing the Wah and the Whammy effects simultaneously, you need to press the IA-switch to get the Mixer block to work
 
  
Method 2 (i.e. using a single pedal control Vol and Wah): (source: Bakerman)
 
# Place a Volume block on the grid.
 
# Assign an IA switch to an external controller's CC.
 
# Assign another external controller the Wah and Volume control knobs.
 
# Set the first external controller as a Bypass modifier for both blocks and reverse the slope of one (start 100, end 0).
 
# Now the IA switch will toggle between Wah/Volume and the pedal will control both.
 
 
Method 3 (using scenes to make the pedal control something else, such as Wah and Whammy and Volume):
 
# Put Wah and Pitch and Volume in one column (parallel).
 
# Assign an external controller (pedal) to the effects. Set to Auto-Engage in Wah and Pitch.
 
# In Wah and Pitch turn down Level in the block's Y state.
 
# Scene 1 is for Wah. Set Wah to X, set Pitch to Y, bypass Volume.
 
# Scene 1 is for Whammy. Set Wah to Y, set Pitch to Y, bypass Volume.
 
# Scene 3 is for Volume. Set Wah to Y, set Pitch to Y, engage Volume.
 
# To make this work with effcts without X/Y support, [http://forum.fractalaudio.com/axe-fx-ii-wish-list/77285-ring-mod-x-y.html#post954149 use a scene controller].
 
 
==MFC-101: connect an expression pedal with a built-in switch==
 
 
Some expression pedals have a separate switch. You can use separate connections for the pedal and the switch and configure the switch to activate an effect which can be controlled with the pedal, such as a wah.
 
Some expression pedals have a separate switch. You can use separate connections for the pedal and the switch and configure the switch to activate an effect which can be controlled with the pedal, such as a wah.
 
# Connect the expression pedal to the MFC using one of the 4 expression pedal inputs on the MFC. Use a stereo (TRS) cable.
 
# Connect the expression pedal to the MFC using one of the 4 expression pedal inputs on the MFC. Use a stereo (TRS) cable.
Line 400: Line 459:
 
# On the Axe-Fx, insert a Wah block in the preset.
 
# On the Axe-Fx, insert a Wah block in the preset.
 
# Set the FREQ or CONTROL parameter of the Wah block to the External controller (the one that's tied to to the expression pedal, see below).
 
# Set the FREQ or CONTROL parameter of the Wah block to the External controller (the one that's tied to to the expression pedal, see below).
# Use Damping if desired. Set PC RST to On. Keep Auto-engage Off because you will be using the switch.
+
# Use Damping if desired. Set PC RST to On. Keep [[Auto-Engage]] Off because you will be using the switch.
 
# Save the preset with the Wah disabled.
 
# Save the preset with the Wah disabled.
 
# In I/O > Ctrl on the Axe-Fx, note which CC is used for the Wah 1 block (default #97).
 
# In I/O > Ctrl on the Axe-Fx, note which CC is used for the Wah 1 block (default #97).
Line 411: Line 470:
 
# Tell the MFC the switch values for Off and On (Edit > MIDI). 000 = Off. 127 = On. If the LED works vice versa, switch the values: 000 = On, 127 = Off.
 
# Tell the MFC the switch values for Off and On (Edit > MIDI). 000 = Off. 127 = On. If the LED works vice versa, switch the values: 000 = On, 127 = Off.
  
=MFC-101: external switches=
+
=External switches=
  
==MFC-101: connect an external switch==
+
You can connect momentary or toggle/latching switches to the rear of the MFC-101. There are 2 inputs which, when using TRS (stereo) cables, support 4 switches in total. A single switch can also be used with a TS (mono) cable, but then you need to set the second switch to Off.
You can connect momentary or toggle/latching switches to the rear of the MFC-101. There are 2 inputs which, when using TRS (stereo) cables, support 4 switches in total. A single switch can also be used with a TS (mono) cable, but you need to set the second switch to Off.
 
  
 
Use Edit > Setup and Edit > Midi to configure external switches.
 
Use Edit > Setup and Edit > Midi to configure external switches.
Line 424: Line 482:
 
Settings in Edit > MIDI are global. If you want program the switch to behave differently with some presets, adjust in Edit > Preset.
 
Settings in Edit > MIDI are global. If you want program the switch to behave differently with some presets, adjust in Edit > Preset.
  
The parameters TyHDW and TypTog and TypAUT control whether an external switch carries over its active state when switching presets:
+
The parameters TyHDW and TypTog and TypAUT control whether an external switch keeps its active state when switching presets:
 
* Latching: when set to TypHDW, the state is carried over because the MFC-101 polls the switch after having switched presets. Use TypTOG to prevent polling but this may cause the LED on the external switch to lose sync.
 
* Latching: when set to TypHDW, the state is carried over because the MFC-101 polls the switch after having switched presets. Use TypTOG to prevent polling but this may cause the LED on the external switch to lose sync.
 
* Momentary: when set to TypHDW, they operate as a momentary switch and retaining states is irrelevant. Use TypTOG to simulate a latching (toggle) switch, but the switch won't retain its state.
 
* Momentary: when set to TypHDW, they operate as a momentary switch and retaining states is irrelevant. Use TypTOG to simulate a latching (toggle) switch, but the switch won't retain its state.
  
Read this: [http://forum.fractalaudio.com/axe-fx-ii-discussion/86024-wicked-wiki-18-a.html Wicked Wiki].
+
[https://forum.fractalaudio.com/threads/wicked-wiki-18-external-s-witchcraft.86024/ Wicked Wiki article]
 +
 
 +
=Troubleshooting=
  
=MFC-101: troubleshooting=
 
 
Noise issues:
 
Noise issues:
* Change the Axe-Fx II's MIDI channel (I/O > MIDI) from Omni to 1.
+
 
* Don't place the MFC-101 nearby powered speakers or on top of the Axe-Fx.
+
* change the Axe-Fx II's MIDI channel (I/O > MIDI) from Omni to 1
* Ticking or clicking sound in sync with Tap Tempo is probably interference from your MIDI cable, leaking into your guitar pickup or guitar cable. Make sure to route the MIDI cable away from anything that it may interfere with, or use CAT5 or XLR. Or switch off "Send Realtime Sysex" when you don't need to use the Tuner and Tap tempo. [http://forum.fractalaudio.com/axe-fx-ii-discussion/43099-first-live-show-fractal-good-bad-clicking-sound.html#post570956 source] Another source might be the 'watch you're wearing! [http://forum.fractalaudio.com/threads/ticking-clock-sound-on-presets.109314 source]
+
* don't place the MFC-101 nearby powered speakers or on top of the Axe-Fx
 +
* ticking or clicking sound in sync with Tap Tempo is probably interference from your MIDI cable, leaking into your guitar pickup or guitar cable. Make sure to route the MIDI cable away from anything that it may interfere with, or use CAT5 or XLR. Or switch off "Send Realtime Sysex" when you don't need to use the Tuner and Tap tempo. Another source might be the watch you're wearing. [http://forum.fractalaudio.com/threads/ticking-clock-sound-on-presets.109314]
  
 
Switch issues:
 
Switch issues:
* If the MFC-101 won't scroll down anymore, switch #1 may be stuck. Depress it a number of times. [http://forum.fractalaudio.com/mfc-wishes-bugs/42153-admin-midi-foot-controller-stopped-down-scrolling-during-performance.html source]
+
* if the MFC-101 won't scroll down anymore, switch #1 may be stuck. Depress it a number of times
* When none of the switches or connnected pedals operate until you switch presets, try powering the Axe-Fx before the MFC.
+
* when none of the switches or connnected pedals operate until you switch presets, try powering the Axe-Fx before the MFC
  
 
Solving the "Waiting for tuner" message:
 
Solving the "Waiting for tuner" message:
* The Axe-Fx II Tuner must be on its first page.
+
* the Axe-Fx II Tuner must be on its first page
* Verify that SendRealtimeSysex in the Axe-Fx's MIDI menu is set to All or Tuner.
+
* verify that SendRealtimeSysex in the Axe-Fx's [[MIDI/Remote menu]] is set to All or Tuner
  
 
"Name timeout..." message:
 
"Name timeout..." message:
* Set the MFC- 101 to the correct port and same MIDI channel as the Axe-Fx II. Make sure the cable is connected firmly at both sides. It that doesn't help: try another cable. If that doesn't help: clean the connections at both sides (blow air).
+
* set the MFC- 101 to the correct port and same MIDI channel as the Axe-Fx II. Make sure the cable is connected firmly at both sides. It that doesn't help: try another cable. If that doesn't help: clean the connections at both sides (blow air)
* Read par. 14.6 of the manual.
+
* read par. 14.6 of the manual
  
=MFC-101: 3D image=
 
[http://3dwarehouse.sketchup.com/model.html?id=ud6398579-2d83-432c-83a0-52c17d76acda 3D image of the MFC-101]
 
  
[[category:MIDI]]
+
[[category:Remote]]
[[category:Connecting]]
+
[[category:Axe-Fx2]]
 +
[[category:Axe-Fx3]]
 +
[[category:All]]

Revision as of 17:42, 12 January 2024

The MFC-101 has been discontinued. This page will not be updated.

MFC-101 and Axe-Fx III

The MFC-101 is a MIDI controller, with specific support for the Axe-Fx II (Axe-Fx Mode). The MFC-101's Axe-Fx mode is NOT compatible with the Axe-Fx III. However, the MFC-101 can still be used as a general MIDI foot controller with the Axe-Fx III. This requires a 5-pin MIDI cable connection. MIDI phantom power is not supported. You can use a 5-to-7 pin MIDI cable, such as this one, to provide the MFC with power. SysEx is not supported, as documented in the Guide on this page, which means that the MFC is not able to show the tempo or the tuner.

These tutorials in English and German explain how to set up the MFC-101 with the III.

Pictures

Owners of an AX8 proudly show their rigs

3D image of the MFC-101

MFC.png

Hardware

Discontinued

The MFC-101 is no longer available from Fractal Audio. It has been replaced with the FC-6 and FC-12 foot controllers.

Mark I, Mark II and Mark III models

Mark I — Original model.

Mark II

FRACTAL AUDIO QUOTES


[1] The only change is the CAT-5 connector is now an Ethercon jack. An Ethercon jack will work with either a CAT-5 cable or an Ethercon cable.

Mark III — Solid-state switch technology. No moving parts except a spring "actuator". Switching is fully electronic and silent with no switches to wear out. Mechanical lifespan is 1 million actuations. FASLINK connector. Requires separate firmware.

Test mode

Press Edit, followed by Reveal, to enter the hardware’s Test mode.

Manufacturing details

FRACTAL AUDIO QUOTES


The MFC-101 is fully made in China.

[2] MFCs don't have a battery.

Expansion port

The internal PSU for the MFC-101 will also support an expansion module for the MFC-101, but such a module has never been released.

For external control of the MFC-101, use either external switches or a MIDI switcher that sends MIDI Program Changes.

LEDs

With the MFC-101 in Axe-Fx Mode:

  • Red — Effect is present in the preset, bypassed.
  • Green — Effect is present in the preset, enabled.
  • Off — Effect is not present in the preset.

You can disable Red LEDs (Edit > Setup > Set IAOffLed Off), which works better for colorblind people.

Tip: put small bits of painter's tape on top of the switch to decrease the LED brightness.

Software

MFC-Edit editor

MFC-Edit was the official editor for the MFC-101. It has been discontinued.

Owners Manual - Addendum regarding the Axe-Fx III

About MFC-Edit and Mac OS Catalina

Axe-Edit and MFC-101

It's recommended to not use the MFC-101 while Axe-Edit is running. It's possible to do so, but using the MFC-101 can cause audio gaps, and fast switching can cause communications issues. When Axe-Edit detects MFC-101 action, it automatically switches into Pause mode.

Engaging and bypassing effects on the MFC-101 will not always update the visual block states in Axe-Edit. To make Axe-Edit recognize such changes, its polling mechanism must be engaged and Pausing must be disabled. This can be accomplished by attaching the Bypass parameter of any block in the preset to a controller, so use a low CPU block. The block doesn't have to be connected to anything on the grid.

Power and connections

Supply power

You can use the supplied 9VAC adapter to power the MFC. This is the recommended way of powering the MFC-101 when upgrading the firmware.

Do NOT connect the adapter to the MFC simultaneously with Ethernet, Ethercon or an XLR cable, or when using MIDI phantom power. Damage can occur!

The Axe-Fx should be powered after the MFC-101, otherwise none of the switches may work until a preset is switched.

FRACTAL AUDIO QUOTES


[3] This happens when the Axe-Fx II is not powered on first. Selecting any preset on the MFC will reset the state machine.

[4] Do NOT attempt to extract power from the MFC connector. It is only rated for 1A and if you burn out the port we won't cover that under warranty.

AxeFxTutorials videos

MFC-101 startup power issue when using 7-pin MIDI cables

The MFC-101's power supply can NOT be used to power an FC controller.

FRACTAL AUDIO QUOTES


[5] It will NOT work. The MFC101 supply is AC, not DC.

Use MIDI

MIDI can be used for communications only (5 pins), or communications plus phantom power (7 pins). A high quality MIDI cable is required. To receive tuner and tempo data, all pins of a 5-pin MIDI cable must be connected. Many low-cost MIDI cables just have 3 pins connected and are not properly shielded, resulting in crosstalk.

To use phantom power via MIDI, a 7-pin MIDI cable is required. All pins must be wired (pins 6 and 7 carry power). Connect the 9VAC adapter to the phantom power input at the rear of the Axe-Fx (the Axe-Fx II doesn't provide power itself, it needs the power supply).

The connection method must be specified in the I/O menu and in the configuration of the MFC-101.

Use Ethernet or Ethercon

A CAT5 Ethernet cable can be used for communications and power, instead of MIDI. It provides power from the Axe-Fx II to the MFC-101 without requiring connecting the power supply to the Axe-Fx II, transmits MIDI data and tuner and tempo information, and switches off the MFC-101 automatically when the Axe-Fx II is turned off.

Mark II and III models also support Ethercon which is sturdier than Ethernet.

When using Ethernet/Ethercon, the MFC's MIDI OUT port won't pass data anymore. You can't use both ports simultaneously. The connection method must be specified in the I/O menu and in the configuration of the MFC-101.

Note that a MIDI interface is still required to perform firmware updates.

Use FASLINK

The 3rd and best way to connect and power the MFC-101 is through FASLINK. This is supported by the Mark III model and the Axe-Fx II XL and XL+. A regular XLR (microphone) cable powers the MFC and transfers data. Connecting the power supply to the Axe-Fx II is not required.

The connection method must be specified in the I/O menu and in the configuration of the MFC-101.

Read this: FASLINK

Note that a MIDI interface is still required to perform firmware updates.

Two MFC-101s

FRACTAL AUDIO QUOTES


[6] True Master Slave is not possible. Split merge works in theory, but there can be hiccups. One MFC can respond to program changes from another, but the two units won't appear to be in any kind of sync.

System configuration

Initial configuration

Read the Quick Start Guide.

Basics:

  1. Use the Edit menu to program the MFC-101. There's no software editor. You may have to press Edit for a couple of seconds (long press), depending on a configuration setting.
  2. Make sure you select the correct Axe-Fx model (Edit > Setup) and connection port (Edit > MIDI).
  3. Decide whether you want to use Axe-Fx Mode or not (Edit > Setup).
  4. Choose the desired Bank Size (Edit > Setup). The MFC supports 384 presets.
  5. Use Edit > Midi to configure the IA switches.

G66 provides several tutorials.

Firmware updates

Go through Edit > Setup to see the currently loaded firmware version.

All firmware release notes can be found here: Firmware release notes - MFC-101

Download the latest MFC-101 firmware, launch Fractal-Bot and follow the instructions. Note that there are different firmware files for the various hardware models.

The update process requires a MIDI interface. Updating is not possible via Ethernet/Ethercon or FASLINK. During the update process, the MFC-101 cannot be powered via MIDI phantom power. The firmware file includes a Read Me - Firmware Update Guide, explaining the process. It also decribes how to configure the Axe-Fx II as a MIDI interface, and how to power the MFC-101 via Ethernet/Ethercon during updating if you haven't got the power supply.

An upgrade may require you to reset the MFC-101 to its factory settings. If so, it will be stated in the release notes. To reset the MFC-101, power on while holding switch #11. Note: this erase all configured settings. You can save these on forehand and restore these afterwards using Fractal-Bot or MFC-Edit.

If you're experiencing problems, go to Utility > Preset on the Axe-Fx II. This makes sure the Axe-Fx II is not transmitting stuff which could interfere with the update process.

Error messages during updating:

  • Error 14 — rare problem that occurs after a failed firmware update. Once this occurs, you can start over to achieve success, but the MFC-101 will “time out” if the update is not completed quickly enough, causing the unit to display ERROR 14 again. Decrease the MIDI Buffer Delay setting in Fractal-Bot (in step 1 “READY”) to 90ms or lower to speed the firmware transmission process. Alternatively, try to slow things down by increasing buffer delay to, say, 400.
  • Error 16 — usually indicates that the MFC saw “garbage” during a firmware update. This problem is often seen when using “inferior” MIDI Interfaces, but can also indicate computer problems, or even a bad MIDI cable. In rare cases, re-downloading the firmware update can also solve this problem.
  • Error 18 — indicates that the MFC-101 has received some stray MIDI message while awaiting a firmware update. Please make sure no other MIDI applications are running on your computer, or, if using the Axe-Fx II as a MIDI Interface, ensure that I/O: MIDI: SEND REALTIME SYSEX is set to “NONE”.

The manual lists and explains other error messages.

Backup and restore

Use Edit > Setup > Sysex Data, when using a MIDI librarian. Or use Fractal-Bot of MFC-Edit.

Restore factory defaults

Power the MFC-101 while holding switch 11.

The manual lists all factory default settings.

TotalSync

When you switch presets or engage/bypass effects on the front panel of the Axe-Fx II or in Axe-Edit, the MFC-101 can switch along. It's called TotalSync which can be enabled and disabled in the MFC's MIDI menu.

TotalSync doesn't work in Song and Set modes, and custom MFC-101 Tx Map and Axe-Fx II preset remapping (for example to support scenes) are not supported.

MIDI channel(s)

By default the MFC-101 sends MIDI Program Changes on all MIDI channels, regardless of the selected MIDI channel on which the MFC-101 operates.

To disable this behavior: [7]

  1. Optionally reset the MFC-101 to FACTORY settings if you also want to do the step noted in "PS".
  2. Temporarily set BANK SIZE to 17.
  3. Turn off all PCs in preset 1.
  4. Edit: COPY PRESET 1 to preset locations 2 through 17.
  5. Edit COPY BANK 1 to bank locations 2 through the end.

P.S. Make a backup of the initialized MFC with all PCs off, so you can avoid ever needing to do this again, no matter what setup you require in the future.

The MFC-101 can receive Program Changes from another MIDI device to switch presets.

  1. Connect a MIDI controller to the MIDI IN port on the MFC-101.
  2. Select the correct MIDI channel for the added device in Edit > System.
  3. Enable Receive Program Changes in Edit > System.

Tuner and tap tempo

To show the Tuner display and see the Tempo LED blink in the correct tempo on the MFC-101, the MFC-101 must be in Axe-Fx Mode. Also, a connection type must be used which supports 5-pin MIDI, CAT5 (Ethernet/Ethercon) or FASLINK. On the Axe-Fx II (I/O > MIDI) Send Realtime Sysex must be set to: Tuner, Tempo, or All.

The MFC won't display tuner data when using an external switch to turn on the tuner. It will be displayed on the Axe-Fx's screen though.

When the Tuner on the Axe-Fx is set to anything other than its first page, the message "Waiting for tuner" appears.

When the tuner display is active, it's still possible to engage/bypass other effects, switch banks, presets and songs etc.

You can combine Tap Tempo and Tuner functionality: hold Tap Tempo will enter the Tuner mode. Use Edit > Setup to set this up. This does not work with external switches.

To use an external switch to control Tap Tempo:

  1. Connect the switch to one of the switch inputs on the MFC
  2. Set the switch type in Edit > Setup to Toggle or Momentary, depending on the switch
  3. In Edit > MIDI > XS set the switch to control CC #14
  4. In Edit > MIDI > XS set the switch to TypTOG.

Presets, scenes, songs, setlists

Access presets 384 and up

The Axe-Fx II XL and XL+ provide more than 384 presets. To access these with the MFC-101, MIDI mapping (transmit table) must be used, either on the MFC or Axe-Fx. Here's how

FRACTAL AUDIO QUOTES


[8] The MFC-101 stores 384 presets. The Axe-Fx II Mark I/II also store 384 presets. Many MIDI controllers only store 128 presets. There is no correlation between the number of presets on a MIDI controller and the device being controlled.

Number of presets per bank, number of IA switches

The MFC-101 defaults to 5 presets per bank. It can be set to any number. Use Edit > Setup > Bank Size to change this, depending on how many IA switches you want to be accessible directly without needing to press Reveal.

  • When using size "0", use the Up/Down switches to scroll through banks and automatically load the preset.
  • When using size "1", use the Up/Down switches to scroll through banks, then press switch 1 to load the preset. If you want the bank number to be the same as the preset number, set Display Offset on the Axe-Fx II to 1, set Offset Axe-Fx on the MFC to 1 and set Offset MFC-101 to 1.

Bank Size also influences Song and Set Mode.

Preset switches start from the bottom row by default. You can change this using the parameter FirstPresetSwitch. This lets you specify where the presets start on the board (preceding switches automatically are IA switches). Note that the FirstPresetSwitch parameter is not supported on the Mark I and II models.

The MFC-101 doen't support preset switching by entering the number of a preset.

Bank Style parameter

Use Edit > Setup > Bank Style to tell the MFC-101 what to do when changing banks:

  • automatically load the first preset of the bank
  • automatically load the preset at the current position in the bank (default)
  • nothing

When set to NONE, banking up/down will show the bank number and the preset range within the bank (Smart Banks feature).

The speed of scrolling through Banks, Songs and Sets cannot be adjusted.

When using Bank Size "0", use the Up/Down switches to scroll through banks and automatically load the "Autoload" preset.

Bank/Song Limit and Bank/Song Wrap parameters

You may need access to just a subset of all available banks on the MFC-101. The Bank/Song Limit parameter lets you define the range of this subset. This prevents having to scroll through banks/songs you don't need.

Also, you may want to stop scrolling through banks/songs after reaching the first or last bank/song (no wrapping around). The Bank/Song Wrap parameter lets you enable/disable this.

Global Preset

Set Global Preset to ON (off by default) in Edit > Setup and select the preset that you want to have as a global preset.

The Global Preset preset can now be recalled at any time by pressing a preset switch a 2nd time. The MFC will display "GBL" while the Global Preset is active. You can switch to other scenes within that preset and engage/bypass individual blocks. Pressing the preset another time (3rd time) returns you to the previous preset. However, if you press another preset switch instead (not the one from which you switched to the Global Preset), that preset will be recalled.

You can specify which scene you want to recall when using Global Preset by using Custom Mapping on the Axe-Fx (I/O > MIDI).

Turn off Global Preset if you want to be able to recall a preset in its saved state by pressing a preset switch a second time (see: Panic switch).

Read this: Wicked Wiki article

Alternate Presets

Pressing a preset switch a second time lets you activate another preset, which can be different per preset. This is an alternative to using a Global Preset (see above) or Backtracking (see below). Set this in the Preset menu on the MFC-101. Note that the "alternate preset" is a MIDI Program Change, not a "preset switch" as configured on the MFC.

Read this: Wicked Wiki article

You use Alternate Preset in combination with scenes on the Axe-Fx by mapping presets to scenes on the Axe-Fx II.

Backtracking

Backtracking means that a pressing a preset switch a second time will recall the previous preset. Set this per preset (Edit > Preset) or configure Global Preset to act as Backtrack ("BAK"). Backtracking always recalls scene 1.

Read this: Wicked Wiki article

Scene switching

The MFC-101 offers special support scenes:

  • recall any of the 8 scenes directly
  • increment or decrement scenes
  • toggle between scenes 1 and 2

You can also use general MIDI commands to switch scenes, or use external momentary switches.

Use Mapping in the MIDI/Remote menu on the Axe-Fx II if you want preset switches to switch to specific scenes. For example, if you want the first 5 preset switches on the MFC to switch to preset 000, scenes 1-5, use Mapping.

The parameter Scene Revert determines what happens with effect states when switching scenes with a MIDI controller.

Songs and sets

Song and Set names on the MFC start with a "S". You can assign up to 15 presets per song, depending on the Bank Size setting. The MFC supports up to 100 songs. Preset switches in Songs can be set to OFF.

You can also use Song Mode to circumvent a limitation of the regular preset mode. In Preset Mode banks have no names, you have to remember which presets are in numbered banks. However, if you assign presets to songs in Song Mode, maintaining the bank structure, you can name them.

Sorting a Song or Set list is not possible.

You cannot set scenes. A preset in a song will always load scene 1.

An alternative to Song Mode: Scenes

Instant Access switches

Axe-Fx Mode (slave) or non-Axe-Fx Mode (master)

When the MFC-101 runs in Axe-Fx Mode, the IA effect switches, adhere to their state in the currently loaded preset on the Axe-Fx II. So the Axe-Fx II is master and the MFC-101 is slave.

Vice versa, when the MFC-101 does not run in Axe-Fx Mode, the MFC-101 determines the state of the switch and effect. In non-Axe-Fx mode, Tuner and Tap Tempo are not displayed on the MFC-101.

Configure IA switches

Any switch can operate as a toggle (latching) or as a momentary switch, and can be given a 7-character name (Edit > Setup).

IA switches can be assigned to specific Axe-Fx II functions (selected from a list) or configured to perform MIDI functionality.

In Axe-Fx Mode, go to Edit > Midi > IA and select the desired block for each switch from the list of effects. In Axe-Fx Mode, the IA switches operate globally, meaning that you cannot change switch assignments per preset.

When you've assigned an effect to a switch, it enables or bypasses that effect. You can also assign the switch to X/Y, to switch an effect between X and Y. Other available Axe-Fx functions include Vol Inc, Vol Dec and Scenes.

If you select "None", the switch is not assigned to specific Axe-Fx functionality. It will be available for general MIDI use (referred to as: General Use IA Switch). This lets you program MIDI commands. You can send 2 separate MIDI CCs, a MIDI PC and additional custom MIDI commands per switch. Use value 127 to switch on effects, 0 to switch off. Or select OFF to send nothing at all. General Use IAs operate globally (same across all presets).

If Axe-Fx Mode is disabled, the MFC-101 turns into a "master" device and determines which effect in a preset is engaged or bypassed (Edit > Preset). In this case preset names in Preset Mode are preced by a "P" (instead of "X").

Keep IA switch states when switching presets

You may want "general MIDI function" IAs to carry over their active state when switching presets. This is controlled through the Global and Send w/Preset parameters. Global defaults to Off, and Send w/Preset defaults to On. See the table in the Owner's Manual for a description of these parameters.

Grouped switches (switch linking)

The Switch Links setting lets you define a group of switches. Within that group only one setting can be active, so selecting one switch will automatically disable the others within the group (they're mutually exclusive). There's a maximum of two groups and 5 switches per group. Switch Links is particularly useful to switch channels on an external amp which supports MIDI.

Turn an IA switch into a preset switch

  1. Set the switch function to None (Edit > MIDI).
  2. Scroll to the PC page, set it to On and specify the Program Change number.
  3. Set the Switch Type (Edit > Setup) to Momentary, for correct LED behavior.

To also make the MFC-101 switch to the Bank containing the preset, enable TotalSync.

This is a great alternative to the Global Preset feature.

Engage/bypass multiple effects at once

Here's a trick that lets you assign multiple effects to one switch (source: Admin M@).

  1. Pick a (low CPU) surrogate such as VOLx or FILTERx, set to NULL. On the Axe-Fx II, go to I/O > CTRL and assign the same MIDI CC to your surrogate and all of the effects you want assign across the single footswitch.
  2. Place the surrogate effect block (disconnected) in every preset that has your target block(s).
  3. Set its bypass state and that of the assigned effect(s) to the same initial state.
  4. Assign the surrogate to the Axe-Fx IA in the MFC-101.
  5. Now you have've got bi-color-LED-enabled control over different multiple blocks across different patches from a single IA switch.

Alternatively: assign the same CC (or an external controller) to all desired effects. But you won't get multi-color LEDs.

Use a single IA switch to toggle between two effects

Set up the switch to send a CC to an external controller. Assign Bypass in two effect blocks to the same controller. Set the Start value of one block to 100 and the other to 0.

An example when alternating between Comp and Drive: set one of the externals to the same CC as COMP, then use it to bypass Drive. Set the switch to COMP and you'll get RED=DRIVE, GREEN=COMPRESSOR.

Switch between two effect speeds

You can use a switch to change speeds (tremolo, vibe, phaser etc.):

  1. Assign an external controller to the effect's Rate parameter.
  2. Enter Min and Max values in the modifier menu.
  3. On the MFC assign a switch to the controller's MIDI CC.

To force a gradual change between the two settings, increase Damping in the modifier menu of the effect parameter on the Axe-Fx.

Switch for leads

  • Use a dedicated preset.
  • Configure a Global Preset (press any preset twice to recall the solo preset).
  • If you have various solo presets, use the Alternate Preset feature (press a preset switch twice to recall an "alternate" preset for that switch).
  • If you use Song Mode, create solo presets and assign them to songs.
  • If you prefer IAs, configure a switch to change the state of two effects at once. If two effects is not enough, you can use custom MIDI to configure more. Or assign a single CC to multiple effects on the Axe-Fx II (I/O > Ctrl), and change them all in one go with a single switch.
  • Use Scenes.

Panic switch

At times it's handy to quickly recall the current scene in its saved state (revert), just by pressing the current scene switch a second time. This will reset any changed IAs to their save state for this scene. This requires that Scene Revert is set to ON.

Alternatively you can also press the preset switch (the current one) again. This loads scene 1 of the current preset in its saved state. This requires that Global Preset is not enabled. Set Ignore Redundant PC to Off to prevent audio gaps.

Expression pedals

Connect and calibrate an expression pedal

You can connect up to 4 expression pedal(s) to the rear of the MFC-101. Expression pedals need 1/4" TRS (stereo) cables.

Use Edit > Setup and Edit > MIDI to configure the pedals. Edit > Preset lets you override global expression pedal settings.

Note that the PEDAL menu on the Axe-Fx II is not used when configuring pedals which are connected to the MFC-101.

By default pedal #1 is mapped to CC 11 (global Output 1 volume) and pedal #2 to CC 16 (External 1). Pedals 3 and 4 default to OFF, which may not be obvious because the MFC will let you calibrate the pedals.

Calibration of pedals: read chapter 7 of the MFC-101 manual. Note that it's normal for pedals to not employ the full value range (0 - 127). If your pedal only gets to 100 or so, it can still perform 100%. Near the end of the test you can test the pedals. Note: after calibration you can check if the pedal goes from 0 to 127 by entering the MFC's test mode (see above).

Use the Beginning Value parameter (Edit > Midi) to define the state of the pedal after switching presets. "PDL" means that the position of the pedal is polled and recalled, "Off" means that the pedal is off until moved (default), or you can select a specific value between 0 and 127.

The modifier menu on the Axe-Fx II allows further control of parameters.

While you can define/limit the operational range of an expression pedal (globally or per preset), you also use the Modifier menu of effects blocks on the Axe-Fx II for this purpose.

Settings in Edit > MIDI are global. If you want to program a pedal to behave differently in specific presets, adjust the settings in Edit > Preset.

Connect an expression pedal with a built-in switch

Some expression pedals have a separate switch. You can use separate connections for the pedal and the switch and configure the switch to activate an effect which can be controlled with the pedal, such as a wah.

  1. Connect the expression pedal to the MFC using one of the 4 expression pedal inputs on the MFC. Use a stereo (TRS) cable.
  2. Connect the switch to one of the 2 switch inputs on the MFC. Use either a stereo (TRS) or mono (TS) cable. If using a mono cable, disable the other connection of the switch in the setup menu.
  3. On the Axe-Fx, insert a Wah block in the preset.
  4. Set the FREQ or CONTROL parameter of the Wah block to the External controller (the one that's tied to to the expression pedal, see below).
  5. Use Damping if desired. Set PC RST to On. Keep Auto-Engage Off because you will be using the switch.
  6. Save the preset with the Wah disabled.
  7. In I/O > Ctrl on the Axe-Fx, note which CC is used for the Wah 1 block (default #97).
  8. In I/O > Ctrl on the Axe-Fx, note which CC is used for the External controller which is tied to the expression pedal, mentioned above.
  9. In I/O > Midi on the Axe-Fx, verify that the External controller which is tied to the expression pedal is set to 0%.
  10. Make sure that the expression pedal is calibrated (Edit > Setup on the MFC).
  11. Make a connection between the pedal and the Axe-Fx by selecting the right CC and channel in Edit > MIDI on the MFC. Make sure you select the correct pedal input (XP1 - XP4). The CC must match the External controller's CC on the Axe-Fx (see above).
  12. In Edit > Setup on the MFC set the external switch to Toggle. Make sure you select the correct switch input (XS1 - XS4).
  13. Make a connection between the switch and the Axe-Fx by selecting the right CC and channel in Edit > MIDI on the MFC. Make sure you select the correct switch input (XS1 - XS4). The CC must match the CC of the Wah block on the Axe-Fx (see above). Set type to HDW. When using a mono cable for the switch, disable the other connection (set it to Off) to prevent MIDI problems.
  14. Tell the MFC the switch values for Off and On (Edit > MIDI). 000 = Off. 127 = On. If the LED works vice versa, switch the values: 000 = On, 127 = Off.

External switches

You can connect momentary or toggle/latching switches to the rear of the MFC-101. There are 2 inputs which, when using TRS (stereo) cables, support 4 switches in total. A single switch can also be used with a TS (mono) cable, but then you need to set the second switch to Off.

Use Edit > Setup and Edit > Midi to configure external switches.

You can specify whether the external switch is a momentary or latching switch type.

An external switch can control a single MIDI CC, using value 0 for off and 127 for on. You can't use them for preset switching (MIDI PCs) or custom MIDI stuff.

Settings in Edit > MIDI are global. If you want program the switch to behave differently with some presets, adjust in Edit > Preset.

The parameters TyHDW and TypTog and TypAUT control whether an external switch keeps its active state when switching presets:

  • Latching: when set to TypHDW, the state is carried over because the MFC-101 polls the switch after having switched presets. Use TypTOG to prevent polling but this may cause the LED on the external switch to lose sync.
  • Momentary: when set to TypHDW, they operate as a momentary switch and retaining states is irrelevant. Use TypTOG to simulate a latching (toggle) switch, but the switch won't retain its state.

Wicked Wiki article

Troubleshooting

Noise issues:

  • change the Axe-Fx II's MIDI channel (I/O > MIDI) from Omni to 1
  • don't place the MFC-101 nearby powered speakers or on top of the Axe-Fx
  • ticking or clicking sound in sync with Tap Tempo is probably interference from your MIDI cable, leaking into your guitar pickup or guitar cable. Make sure to route the MIDI cable away from anything that it may interfere with, or use CAT5 or XLR. Or switch off "Send Realtime Sysex" when you don't need to use the Tuner and Tap tempo. Another source might be the watch you're wearing. [9]

Switch issues:

  • if the MFC-101 won't scroll down anymore, switch #1 may be stuck. Depress it a number of times
  • when none of the switches or connnected pedals operate until you switch presets, try powering the Axe-Fx before the MFC

Solving the "Waiting for tuner" message:

  • the Axe-Fx II Tuner must be on its first page
  • verify that SendRealtimeSysex in the Axe-Fx's MIDI/Remote menu is set to All or Tuner

"Name timeout..." message:

  • set the MFC- 101 to the correct port and same MIDI channel as the Axe-Fx II. Make sure the cable is connected firmly at both sides. It that doesn't help: try another cable. If that doesn't help: clean the connections at both sides (blow air)
  • read par. 14.6 of the manual