Read the Owners Manual first!
Difference between revisions of "Phaser block"
Jump to navigation
Jump to search
| Line 1: | Line 1: | ||
''The information on this page supplements the official manuals.'' | ''The information on this page supplements the official manuals.'' | ||
__TOC__ | __TOC__ | ||
| − | =Phaser: supported by which Fractal Audio products | + | =Phaser: supported by which Fractal Audio products= |
* '''Axe-Fx II''': yes. | * '''Axe-Fx II''': yes. | ||
* '''AX8''': yes. | * '''AX8''': yes. | ||
* '''FX8''': yes. | * '''FX8''': yes. | ||
| − | =X/Y | + | =Phaser: X/Y support= |
The Phaser block in the Axe-Fx II, AX8 and FX8 supports X/Y switching. | The Phaser block in the Axe-Fx II, AX8 and FX8 supports X/Y switching. | ||
| − | =Phaser: mono or stereo | + | =Phaser: mono or stereo= |
Phaser defaults to mono to prevent phase problems when used before an Amp block. To make it stereo, change the LFO Phase setting and place it after Drive, Amp and (mono) Cab. | Phaser defaults to mono to prevent phase problems when used before an Amp block. To make it stereo, change the LFO Phase setting and place it after Drive, Amp and (mono) Cab. | ||
| − | =Feedback Tap parameter | + | =Feedback Tap parameter= |
| − | |||
| − | |||
| − | = | + | <blockquote>"There is no feedback on a Script 90." [http://forum.fractalaudio.com/axe-fx-ii-bugs/52270-phaser-type-feedback-tap-incorrect-script-90-type.html#post669003 source] </blockquote> |
| + | |||
| + | =Thump when engaging the Phaser= | ||
If engaging/bypassing the Phaser block causes an audible thump or gap, change input impedance to 1M (Axe-Fx II and FX8). | If engaging/bypassing the Phaser block causes an audible thump or gap, change input impedance to 1M (Axe-Fx II and FX8). | ||
=Control the start of the Phaser sweep= | =Control the start of the Phaser sweep= | ||
| − | + | If the parameter “LFO Bypass Reset” is set to anything other than “Off”, the LFO will be reset to the selected phase whenever the block is bypassed. This allows synchronizing the sweep to the engagement of the effect. | |
| − | = | + | =Uni-vibe effect= |
The Vibe effect is available as a special mode of the Phaser block. Set Vibe Mode to On (or select the Classic Vibe type). The default settings are modeled after the Fulltone Deja-Vibe. [http://forum.fractalaudio.com/threads/need-help-with-some-sounds.109156/#post-1305852 source] | The Vibe effect is available as a special mode of the Phaser block. Set Vibe Mode to On (or select the Classic Vibe type). The default settings are modeled after the Fulltone Deja-Vibe. [http://forum.fractalaudio.com/threads/need-help-with-some-sounds.109156/#post-1305852 source] | ||
| − | + | <blockquote>"You need it before the amp if you want the bump." [http://forum.fractalaudio.com/axe-fx-ii-discussion/104710-recommendations-achieve-good-univibe-sound.html#post1252527 source] </blockquote> | |
| − | "You need it before the amp if you want the bump." [http://forum.fractalaudio.com/axe-fx-ii-discussion/104710-recommendations-achieve-good-univibe-sound.html#post1252527 source] | ||
Tip: connect a pedal or switch (via an external controller) to the Rate parameter to control speed. | Tip: connect a pedal or switch (via an external controller) to the Rate parameter to control speed. | ||
| − | [http://forum.fractalaudio.com/axe-fx-ii-preset-exchange/83367-still-looking-perfect-fat-robin-trower-univibe-sound-3.html Robin Trower vibe settings] | + | [http://forum.fractalaudio.com/axe-fx-ii-preset-exchange/83367-still-looking-perfect-fat-robin-trower-univibe-sound-3.html Robin Trower vibe settings.] |
| − | [http://www.gilmourish.com/?page_id=4537 More information about the Uni-Vibe] | + | [http://www.gilmourish.com/?page_id=4537 More information about the Uni-Vibe.] |
=Barber Pole Phaser type= | =Barber Pole Phaser type= | ||
| Line 38: | Line 37: | ||
=More information= | =More information= | ||
| − | * [http://en.wikipedia.org/wiki/Phaser_(effect) Phaser in Wikipedia] | + | * [http://en.wikipedia.org/wiki/Phaser_(effect) Phaser in Wikipedia.] |
| − | * [http://en.wikipedia.org/wiki/Univibe Uni-Vibe in Wikipedia] | + | * [http://en.wikipedia.org/wiki/Univibe Uni-Vibe in Wikipedia.] |
[[category:Effect]] | [[category:Effect]] | ||
Revision as of 17:18, 27 November 2017
The information on this page supplements the official manuals.
Contents
Phaser: supported by which Fractal Audio products
- Axe-Fx II: yes.
- AX8: yes.
- FX8: yes.
Phaser: X/Y support
The Phaser block in the Axe-Fx II, AX8 and FX8 supports X/Y switching.
Phaser: mono or stereo
Phaser defaults to mono to prevent phase problems when used before an Amp block. To make it stereo, change the LFO Phase setting and place it after Drive, Amp and (mono) Cab.
Feedback Tap parameter
"There is no feedback on a Script 90." source
Thump when engaging the Phaser
If engaging/bypassing the Phaser block causes an audible thump or gap, change input impedance to 1M (Axe-Fx II and FX8).
Control the start of the Phaser sweep
If the parameter “LFO Bypass Reset” is set to anything other than “Off”, the LFO will be reset to the selected phase whenever the block is bypassed. This allows synchronizing the sweep to the engagement of the effect.
Uni-vibe effect
The Vibe effect is available as a special mode of the Phaser block. Set Vibe Mode to On (or select the Classic Vibe type). The default settings are modeled after the Fulltone Deja-Vibe. source
"You need it before the amp if you want the bump." source
Tip: connect a pedal or switch (via an external controller) to the Rate parameter to control speed.
More information about the Uni-Vibe.
Barber Pole Phaser type
This phaser type works best when placed at the end of the chain.
