Always consult the official Owners Manuals first
Difference between revisions of "Volume/Panner block"
| Line 1: | Line 1: | ||
''The information on this page supplements the official manuals.'' | ''The information on this page supplements the official manuals.'' | ||
| + | |||
| + | __TOC__ | ||
[[image:Volumeknob.png|link=|100px]] | [[image:Volumeknob.png|link=|100px]] | ||
| − | + | ||
| − | =Vol/Pan: supported by which Fractal Audio products | + | =Vol/Pan: supported by which Fractal Audio products= |
* '''Axe-Fx II''': yes. | * '''Axe-Fx II''': yes. | ||
* '''AX8''': yes. | * '''AX8''': yes. | ||
* '''FX8''': yes. | * '''FX8''': yes. | ||
| − | =X/Y | + | =Volume block: X/Y support= |
The Volume block doesn't support X/Y switching. | The Volume block doesn't support X/Y switching. | ||
| Line 14: | Line 16: | ||
The Volume block offers various audio tapers. | The Volume block offers various audio tapers. | ||
| − | + | <blockquote>"The number is the percentage at the halfway point. I.e. Log 20A means that the resistance is 20% at the halfway point in the travel. So if you put the knob at noon, the volume would be 20% of maximum (about -14 dB)." [http://forum.fractalaudio.com/axe-fx-ii-discussion/58160-volume-blk-volume-tapers.html#post727942 source] </blockquote> | |
| − | "The number is the percentage at the halfway point. I.e. Log 20A means that the resistance is 20% at the halfway point in the travel. So if you put the knob at noon, the volume would be 20% of maximum (about -14 dB)." [http://forum.fractalaudio.com/axe-fx-ii-discussion/58160-volume-blk-volume-tapers.html#post727942 source] | ||
To simulate a Log taper in a modifier menu, set "Mid" in the modifier menu to 20%. Adjust Slope to avoid the dead zone. | To simulate a Log taper in a modifier menu, set "Mid" in the modifier menu to 20%. Adjust Slope to avoid the dead zone. | ||
Revision as of 09:28, 26 November 2017
The information on this page supplements the official manuals.
Contents
Vol/Pan: supported by which Fractal Audio products
- Axe-Fx II: yes.
- AX8: yes.
- FX8: yes.
Volume block: X/Y support
The Volume block doesn't support X/Y switching.
Audio tapers in Volume block
The Volume block offers various audio tapers.
"The number is the percentage at the halfway point. I.e. Log 20A means that the resistance is 20% at the halfway point in the travel. So if you put the knob at noon, the volume would be 20% of maximum (about -14 dB)." source
To simulate a Log taper in a modifier menu, set "Mid" in the modifier menu to 20%. Adjust Slope to avoid the dead zone.
Process one side of the signal in the Volume block
Like the Amp block and Drive blocks, the Input Select parameter enables the Vol/Pan block to operate on the left or right input signal only, or both (stereo). It can send the processed signal to either side, using Balance, or keep it stereo.
Use the Volume block for special tasks
Volume pedal
Assign an expression pedal (through an external controller) to the Volume parameter in the Volume block to create a volume pedal. Place the block either before or after the Amp block.
Automate volume swells
Read this: Volume swells.
Noise gate
Read this: Noise and noise gate.
Signal routing
The Volume block doesn't require much CPU. This makes it a handy tool for routing. Set its Bypass parameter to Mute and put it at the start of a split signal, to enable or disable a certain routing within a preset, depending on the bypass state of the Volume block. You can engage or bypass the block per scene.
Lead boost
Place the block at the end of the signal chain and bump its Level for lead boosts, using scenes or an assigned switch.
