The VP4 has been added to the wiki.
Difference between revisions of "Wah block"
Jump to navigation
Jump to search
Line 1: | Line 1: | ||
− | |||
− | |||
__TOC__ | __TOC__ | ||
− | |||
=Wah: supported by which Fractal Audio products?= | =Wah: supported by which Fractal Audio products?= | ||
* Axe-Fx II: yes. | * Axe-Fx II: yes. |
Revision as of 15:12, 29 March 2017
Contents
- 1 Wah: supported by which Fractal Audio products?
- 2 Wah models
- 3 X/Y switching in the Wah block
- 4 Position of the Wah block
- 5 Preventing thump when engaging the Wah
- 6 Tracking parameter in the Wah block
- 7 FAT parameter in the Wah block
- 8 New Wah block parameters in firmware Quantum 6.x and later
- 9 Wah and Level
- 10 Auto-engaging the Wah
- 11 Creating a Seek Wah
- 12 Creating an Auto Wah
- 13 Various Wah tips
Wah: supported by which Fractal Audio products?
- Axe-Fx II: yes.
- AX8: yes.
- FX8: yes.
Wah models
- Current types in the Wah block:
- FAS Standard – equivalent to the “Bandpass” setting in earlier firmware.
- Clyde – based on an original Vox Clyde McCoy wah.
- Cry Babe – based on a Dunlop Cry Baby.
- VX846 – based on a Vox V846-HW handwired wah.
- Color-Tone – based on a Colorsound wah.
- Funk – modeled after the “Shaft” sound.
- Mortal – based on a Morley wah/volume pedal.
- VX485 - based on a Vox V845.
- Pictures of the real Wah pedal equivalents, by MDProd.
X/Y switching in the Wah block
- Axe-Fx II: yes.
- AX8: yes.
- FX8: yes.
Position of the Wah block
- The Wah block is usually placed before the Amp block. Unless you want to sound like Tom Morello, in which case it should be placed after the Amp block.
Preventing thump when engaging the Wah
- Cliff's comments:
- (answering a question about hearing a thump when auto-engaging a wah): "The thump isn't the wah, it's the Input Impedance changing. If your preset is set to Auto for the Input Z, when you engage the wah the impedance switches. This causes a slight thump if you are playing since the load on your guitar changes. If you want to avoid this, turn Input Impedance to 1M OHM." source
- "Set the Input-Z on the preset to 1M rather than Auto. The reason the Wah engages abruptly is because it switches the input impedance. Setting Input-Z to 1M overrides the impedance switch (and, frankly, sounds better IMO)." source
- The AX8's Input Impedance is fixed at 1 MOhm (not adjustable).
Tracking parameter in the Wah block
- Cliff's comments:
- "Tracking controls how much the Q changes with the Control knob. The Q in a wah is not constant. The amount of Q change varies from brand-to-brand and model-to-model. It even varies between identical models due to component tolerances." source
FAT parameter in the Wah block
- Cliff's comments:
- "FAT is actually a mix control. It adds dry signal so you can't ever get 100% dry. At max FAT it's 50/50." source
New Wah block parameters in firmware Quantum 6.x and later
- Coil Bias: allows the user to adjust the DC offset of the virtual inductor.
- Cliff: "Over time the inductors build up some slight permanent magnetism due to finite DC current through them. This causes asymmetric distortion." source
- Low Cut Freq: sets the highpass filter due to the input coupling capacitor.
Wah and Level
- When changing the Wah type, its Level is also adjusted automatically because the output of the models has been matched to the original pedals (firmware Quatum 6 and later). source
- Cliff's comments:
- "A typical wah has a gain of around 16 dB but it's a bandpass (sort of) response. If your amp is set clean then the output of the amp block will increase by 16 dB when the wah is engaged. Most amps have a response that rises with frequency response. So if the output of the amp block without the wah engaged was, say, 12 dB below full-scale at the high frequencies, it will be 4 dB over full-scale when the wah is engaged." source
Auto-engaging the Wah
- Just like an optical wah pedal, you can engage the Wah automatically when moving the pedal. This is especially handy when using a spring-loaded pedal. To accomplish this, set Auto-Engage in the modifier menu to either a speed-controlled or position-controlled setting. More about Auto-Engage.
- If you want the Wah to be bypassed automatically at toe-down position (simulating a virtual toe switch), instead of heel-down, set OFF VAL in the modifier menu to 95%.
Creating a Seek Wah
- The Seek Wah is a pedal by ZVEX, which uses a sequenced filter pattern. For an equivalent effect, try the Random Wah factory preset in the Axe-Fx II. For a more pronounced effect, try adding a Formant filter, attached to the same controller.
Creating an Auto Wah
Various Wah tips
- Decreasing the MAX FREQ value often helps to make a high gain wah tone cut better through the mix.
- Copying frequency range settings from manufacturer's manuals helps emulating specific wah pedals.