View source for Tremolo/Panner block

__TOC__

[[image:Tremolo block.png|250px]]

=Available on which products=

* '''Axe-Fx III''': 2 blocks
* '''FM3''': yes @@
* '''Axe-Fx II''': 2 blocks
* '''AX8''': 1 block
* '''FX8''': 2 blocks

=Channels or X/Y switching=

* '''Axe-Fx III''' and '''FM3''': 4 channels
* '''Axe-Fx II Mk I''' and '''II''': no
* '''Axe-Fx II XL''' and '''XL+''': X/Y
* '''AX8''': X/Y
* '''FX8''': X/Y

=Position of the Tremolo/Panner block on the grid=

If the Tremolo block is placed before the Amp block and there's a lot of amp gain, the tremolo effect will be less noticeable because of the compression. Adjust the waveform or the Duty parameter to emphasize the pulse. Or move the block to a position after the Amp block.

The Panner pans the signal left and right, just like a ping pong delay. This requires the signal not being summed to mono after the Tremolo/Panner block.

You can make the Panner effect appear “fuller” and “wider” by adding the [[Enhancer block]] after it.

=Parameters=

==Parameters table==

{| class="wikitable"
|-
! '''Parameter'''
! '''Axe-Fx III / FM3'''
! '''Axe-Fx II'''
! '''AX8 / FX8'''
|-
| Type
! yes
! 
! 
|-
| Rate
! yes
! 
! 
|-
| Tempo
! yes
! 
! 
|-
| Depth
! yes
! 
! 
|-
| LFO Type
! yes
! 
! 
|-
| LFO Duty Cycle
! yes
! 
! 
|-
| LFO Phase
! yes
! 
! 
|-
| Start Phase
! yes
!
! 
|-
| Crossover Slope, Freq
! yes
!
! 
|-
| 
! 
! 
! 
|-
| Panner — Width
! yes
! 
! 
|-
| Panner — Pan Center
! yes
! 
! 
|}

==Type==

The block provides the following types in firmware Ares:
* '''Tremolo'''
* '''Panner'''
* '''Bias Trem''' — tube emulation algorithm to replicate the bias tremolo used in vintage tube amps
* '''Harmonic Trem''' — recreates the famous sound of the tremolo circuit in the old “Brownface” amplifiers. This effect splits the spectrum and applies modulation to the two frequency bands. The Crossover Slope parameter selects the filter order for the crossover. The original circuit used a 6 dB/octave crossover. Higher slopes can give a more intense effect. The crossover frequency can be changed with the Crossover Frequency parameter. Note: unlike most implementations the Axe-Fx III version is full stereo and can be used before or after the Amp block without losing stereo separation. Additionally the effect supports LFO phase for the left/right which can be used to achieve unique sounds. Furthermore the effect supports LFO types other than Sine for even more unique sounds

Both Bias Trem and Harmonic Trem use nonlinear processing techniques and, as such, may add distortion to the audio signal, just as their tube-based counterparts would.

<blockquote>"I like the Harmonic Trem on clean and light crunch before an amp. It takes on a slight phaser vibe. Another cool thing to try is to put it near the end of the chain and set the LFO Phase to 180. Funky stereo tremolo." [http://forum.fractalaudio.com/threads/axe-fx-iii-firmware-version-2-03.145132/page-3#post-1716717 source]</blockquote>

[http://forum.fractalaudio.com/threads/the-flint-tremolo-done-right.109107 Forum discussion about harmonic tremolo]

[http://www.strymon.net/amplifier-tremolo-technology-white-paper Strymon's white paper on tremolo types]

==LFO Phase==

Set LFO Phase to 0 for mono output, and to any other value for stereo output.

==Depth==

There's no Mix parameter In the Tremolo block. Depth is the same as Mix, because a tremolo's modulation is volume-based.

<blockquote>"Mix makes no sense in a tremolo as it is the same as reducing the depth." [http://forum.fractalaudio.com/threads/can-we-get-a-mix-knob-for-the-tremolo-block.125674/page-2#post-1495700 source] </blockquote>

==Start Phase==

You can start the Tremolo on the beat (triggered) by using the Start Phase parameter. This applies to engaging the effect, not to hitting the strings.

To align the Tremolo to the moment that you hit the strings, set Rate to “LFO1 SYNC”, sync LFO1 to a Tempo, and attach the LFO to the Envelope follower.

==Duty==

Use this parameter to change the character of the tremolo peaks, from a regular tremolo to electronic "blobs".

=Tips and tricks=

==Tremolo in Amp block==

The [[Amp_block#BIAS_TREM_FREQUENCY_.2B_BIAS_TREM_DEPTH|Amp block]] in the Axe-Fx II and III (not in the AX8 and FM3) provides its own Bias Tremolo.

==Ring Modulator as a tremolo==

You can configure the [[Ring Modulator block]] to operate as a tremolo, by turning down Frequency all the way.

==Flanger as a tremolo==

You can turn a [[Flanger block]] into a tremolo.

==Shuffle tremolo==

[http://forum.fractalaudio.com/axe-fx-ii-discussion/90991-shuffle-tremolo-tempo.html Create a "shuffle" tremolo]

[[category:Axe-Fx2]]
[[category:Axe-Fx3]]
[[category:FM3]]
[[category:AX8]]
[[category:FX8]]
[[category:Sounds]]