Difference between revisions of "Chorus"

From Fractal Audio Wiki
Jump to navigation Jump to search
m (level adjustments)
 
(6 intermediate revisions by 3 users not shown)
Line 2: Line 2:
 
A chorus subtly delays the input signal by a varying amount and mixes it with the undelayed signal. The varying delay slightly detunes the signal so the result is one of multiple instruments playing in unison. The Axe-Fx Chorus is a stereo multi-voice chorus. It uses a very computationally demanding algorithm but delivers exceptionally smooth sounding ensemble effects. Each stereo channel in the chorus can have from one to four voices. Increasing the number of voices increases the fullness of the effect. For classic chorus sounds use two voices (one per side). For thick, full chorus effects use four or more voices
 
A chorus subtly delays the input signal by a varying amount and mixes it with the undelayed signal. The varying delay slightly detunes the signal so the result is one of multiple instruments playing in unison. The Axe-Fx Chorus is a stereo multi-voice chorus. It uses a very computationally demanding algorithm but delivers exceptionally smooth sounding ensemble effects. Each stereo channel in the chorus can have from one to four voices. Increasing the number of voices increases the fullness of the effect. For classic chorus sounds use two voices (one per side). For thick, full chorus effects use four or more voices
  
===Parameters===
+
====Parameters====
====Basic Parameters====
+
=====Basic Parameters=====
 
*'''VOICES''' - Sets the total number of voices used in the effect. For example, a setting of 4 uses two voices per side.  
 
*'''VOICES''' - Sets the total number of voices used in the effect. For example, a setting of 4 uses two voices per side.  
 
*'''RATE''' - Controls the frequency of the Low Frequency Oscillator (LFO). Use low settings with higher depths for slow moving sounds. Increase the rate for vibrato effects. Set fully CCW to sync the LFO to the Global LFO1 oscillator.  
 
*'''RATE''' - Controls the frequency of the Low Frequency Oscillator (LFO). Use low settings with higher depths for slow moving sounds. Increase the rate for vibrato effects. Set fully CCW to sync the LFO to the Global LFO1 oscillator.  
Line 10: Line 10:
 
*'''TEMPO''' - Locks the rate to the global tempo. For example, if the global tempo is 120 bpm and the tempo is set to a quarter note (1/4) then the LFO rate will be 2 Hz (120 bpm / 60 seconds = 2). To ignore the global tempo set the tempo control to '''NONE'''.  
 
*'''TEMPO''' - Locks the rate to the global tempo. For example, if the global tempo is 120 bpm and the tempo is set to a quarter note (1/4) then the LFO rate will be 2 Hz (120 bpm / 60 seconds = 2). To ignore the global tempo set the tempo control to '''NONE'''.  
  
====Advanced Parameters====
+
=====Advanced Parameters=====
 
*'''BASS''' - Adjusts the bass response of the wet signal. The bass can be boost or cut up to 12 dB.  
 
*'''BASS''' - Adjusts the bass response of the wet signal. The bass can be boost or cut up to 12 dB.  
 
*'''TREBLE''' - Adjusts the treble response of the wet signal. The treble can be boost or cut up to 12 dB.  
 
*'''TREBLE''' - Adjusts the treble response of the wet signal. The treble can be boost or cut up to 12 dB.  
Line 16: Line 16:
 
*'''TREBLE FREQ''' - Adjusts the corner frequency of the treble control.  
 
*'''TREBLE FREQ''' - Adjusts the corner frequency of the treble control.  
 
*'''DELAY TIME''' - Adjusts the minimum delay time of the delay line. This can provide subtle changes in the character of the effect.
 
*'''DELAY TIME''' - Adjusts the minimum delay time of the delay line. This can provide subtle changes in the character of the effect.
*'''LFO PHASE''' - Adjusts the phase difference between the left and right lfo waveforms. For maximum stereo spread set this to 180 degrees. For a mono chorus simply set this to zero.  
+
*'''LFO PHASE''' - Adjusts the phase difference between the left and right lfo waveforms. When set to 180 degrees, the right delay time will be a maximum when the left is a minimum and vice-versa. For maximum stereo spread set this to 180 degrees. For a mono chorus simply set this to zero.  
*'''LFO TYPE''' - Selects between sine or triangle waveforms for the LFO. Sine is the most commonly used waveform.  
+
*'''LFO TYPE''' - Selects between sine or triangle waveforms for the LFO. Sine is the most commonly used waveform.
 +
*'''LFO2 RATE''' - Sets the rate of a 2nd LFO. The second LFO amplitude modulates the primary LFO on every other voice. This allows for a lusher chorus effect.
 +
*'''LFO2 DEPTH''' - Sets the depth of a 2nd LFO. The second LFO amplitude modulates the primary LFO on every other voice. This allows for a lusher chorus effect.
 
*'''AUTO DEPTH''' - When this is set to '''LOW''' or '''HIGH''' the depth is automatically scaled for the rate. Lower rates therefore increase the actual depth and vice-versa. The '''HIGH''' setting allows greater maximum depth. This greatly simplifies adjusting the rate and depth and gives the most musical results. For wild sounds you may wish to set this to '''OFF''' which decouples the controls allowing for full depth swing even at fast rates.  
 
*'''AUTO DEPTH''' - When this is set to '''LOW''' or '''HIGH''' the depth is automatically scaled for the rate. Lower rates therefore increase the actual depth and vice-versa. The '''HIGH''' setting allows greater maximum depth. This greatly simplifies adjusting the rate and depth and gives the most musical results. For wild sounds you may wish to set this to '''OFF''' which decouples the controls allowing for full depth swing even at fast rates.  
 
*'''PHASE REVERSE''' - When this is set to '''ON''' the phase of the right channel is reversed on the effected signal. This increases the stereo imaging.
 
*'''PHASE REVERSE''' - When this is set to '''ON''' the phase of the right channel is reversed on the effected signal. This increases the stereo imaging.
 +
*'''WIDTH''' - skews the delay between left and right for a lusher chorus effect. When set to 100% the right delay time will be 1/2 the left value. At 0% they will be equal.
 +
 +
 +
 +
 +
<noinclude>
 +
 +
====Tutorials====
 +
{{:Pitch vibrato}}
 +
 +
{{:Emulating Roland Chorus}}
 +
 +
===Wide guitars with mono compatibility===
 +
{{:Wide guitars with mono compatibility}}
 +
 +
  
 
{{stub}}
 
{{stub}}
 
+
</noinclude>
  
 
[[Category:Effect blocks]]
 
[[Category:Effect blocks]]

Latest revision as of 17:14, 28 September 2009

Chorus block.jpg

A chorus subtly delays the input signal by a varying amount and mixes it with the undelayed signal. The varying delay slightly detunes the signal so the result is one of multiple instruments playing in unison. The Axe-Fx Chorus is a stereo multi-voice chorus. It uses a very computationally demanding algorithm but delivers exceptionally smooth sounding ensemble effects. Each stereo channel in the chorus can have from one to four voices. Increasing the number of voices increases the fullness of the effect. For classic chorus sounds use two voices (one per side). For thick, full chorus effects use four or more voices

Parameters

Basic Parameters
  • VOICES - Sets the total number of voices used in the effect. For example, a setting of 4 uses two voices per side.
  • RATE - Controls the frequency of the Low Frequency Oscillator (LFO). Use low settings with higher depths for slow moving sounds. Increase the rate for vibrato effects. Set fully CCW to sync the LFO to the Global LFO1 oscillator.
  • DEPTH - Sets the maximum delay variation. Higher depths increase the amount of detuning. Usually the rate and depth settings should be varied inversely, i.e. if you increase the rate decrease the depth however some unique sounds can be obtained using high rates and depths.
  • MIX - Sets the ratio of wet and dry. Duplicated from MIX page. A setting of 50% produces the most prominent effect. Try setting the mix to 100% for vibrato effects.
  • TEMPO - Locks the rate to the global tempo. For example, if the global tempo is 120 bpm and the tempo is set to a quarter note (1/4) then the LFO rate will be 2 Hz (120 bpm / 60 seconds = 2). To ignore the global tempo set the tempo control to NONE.
Advanced Parameters
  • BASS - Adjusts the bass response of the wet signal. The bass can be boost or cut up to 12 dB.
  • TREBLE - Adjusts the treble response of the wet signal. The treble can be boost or cut up to 12 dB.
  • BASS FREQ - Adjusts the corner frequency of the bass control.
  • TREBLE FREQ - Adjusts the corner frequency of the treble control.
  • DELAY TIME - Adjusts the minimum delay time of the delay line. This can provide subtle changes in the character of the effect.
  • LFO PHASE - Adjusts the phase difference between the left and right lfo waveforms. When set to 180 degrees, the right delay time will be a maximum when the left is a minimum and vice-versa. For maximum stereo spread set this to 180 degrees. For a mono chorus simply set this to zero.
  • LFO TYPE - Selects between sine or triangle waveforms for the LFO. Sine is the most commonly used waveform.
  • LFO2 RATE - Sets the rate of a 2nd LFO. The second LFO amplitude modulates the primary LFO on every other voice. This allows for a lusher chorus effect.
  • LFO2 DEPTH - Sets the depth of a 2nd LFO. The second LFO amplitude modulates the primary LFO on every other voice. This allows for a lusher chorus effect.
  • AUTO DEPTH - When this is set to LOW or HIGH the depth is automatically scaled for the rate. Lower rates therefore increase the actual depth and vice-versa. The HIGH setting allows greater maximum depth. This greatly simplifies adjusting the rate and depth and gives the most musical results. For wild sounds you may wish to set this to OFF which decouples the controls allowing for full depth swing even at fast rates.
  • PHASE REVERSE - When this is set to ON the phase of the right channel is reversed on the effected signal. This increases the stereo imaging.
  • WIDTH - skews the delay between left and right for a lusher chorus effect. When set to 100% the right delay time will be 1/2 the left value. At 0% they will be equal.




Tutorials

How to create true pitch vibrato

So you'd like to get those sweet vintage Boss VB-2 Vibrato tones out of your squeaky clean new Axe-Fx...here's how.

True pitch vibrato is created by modulating the time on a 100% wet delay line. Think about it. Have you ever twisted the delay time knob on an analog delay to get those cool alien spaceship sounds? Same concept only the knob twisting is done via an LFO and there is no dry sound to water down the effect.

Perusing the Axe-Fx's available effect blocks, the chorus is the best fit for this task. Compared to the delay block, the chorus block allows smaller increments of time delay and doesn't have a feedback (regeneration) path which we don't need anyway.

Checking the Chorus block's basic parameters, we have VOICES which is how many voices our vibrato will have. If you want to nail the VB-2 you'll only need one voice. The minimum choice is 2, but we don't really have to vary but one of the voices. RATE is the rate of the LFO and is directly analogous to the rate control on the VB-2. DEPTH is how much the delay time varies.

According to Cliff, the LFO varies the delay time "bipolar" meaning that it adds and subtracts delay time from the nominal delay time which is set in the advanced parameter menu. MIX should be set 100% wet to vary the pitch of the original signal with no original signal present. TEMPO you can use if you want to lock the rate to a songs tempo.

How to emulate Roland Choruses with the Axe-Fx

(from a post from javajunkie from here: http://www.fractalaudio.com/forum/viewtopic.php?f=11&t=10082&start=0)

Hi All-

I have owned 2 Roland Dimension D rack mount units, and for a long time it was my staple chorus sound. I bought one new when they first came out (wow- that makes me feel old!). I sold them some time ago to raise some cash, but after getting my Ultra I borrowed one back for a while. I tested it extensively both by measurement and listening to see if it was possible to nail that elusive ‘D’ tone with the Axe-Fx.

So- I have some information that you guys might find useful……..here goes……

Firstly due to component tolerances and internal trimpots the units can all be slightly different.

The modulation waveform in the one I had (which sounds great) is almost perfectly triangular with only the tiniest amount of ‘dwell’ caused by the very slight 'rounding off' of the triangle points. I have seen a service diagram in the past and the waveform was also shown as a triangle on that. One side of the modulation is 180 degrees out of phase. The speed and depth of the mod. is controlled by the buttons 1 to 4. The unit has 2 mod speeds, roughly a 2 second and a 4 second cycle with 2 different depths. The triangle wave in the Axe-fx sounds very close when all the other variables are matched.

Just as important is the eq applied to the delay. There is a bass roll off before the compander noise reduction. This can be simulated by placing a parametric eq block after the delay, and using the high pass filter at around 120 hz. There is also a ‘brickwall’ filter at around 8khz applied after the analogue delay lines to filter out the clocking frequency. This is not so easy to simulate perfectly as the Axe-Fx low pass filter is not steep enough. However, using the low pass filter section in the parametric gave very similar and good sounding results.

The compander circuit adds a little bit of program dependant distortion, which gives a small amount of extra ‘warmth’ to the delay. If you wanted to go the whole hog you could follow the parametric eq with a Drive block set to a low value of ‘tape’ distortion to simulate this.

The direct signal has a small (1db) bass lift to compensate slightly for the roll off in the delay. I set the chorus mix to fully wet and used a filter block (adding the bass lift) around the chorus and eq blocks for the direct sound.

The ‘D’ handles stereo signals in a special way. With buttons 1, 2 or 3 depressed the delay component for the left channel appears on the right side and vice versa. Inputting a guitar with stereo bouncing repeats sounds fabulous. Signals retain their stereo position but sound lush, wide and spacious. Button 4 returns the delays to their usual L/R position, and combining 4 with 1, 2 or 3 gives more modulation options.

So- you need a chorus block with independently pannable voices. I used 2 voices of the Ultras quad chorus but you could use a stereo delay and add the modulation. Of course, if you only use a mono input a standard chorus block will do. The delay time is not quite the same in the two channels. I think that for all except button 1 one side is about 5ms and the other about 5.5ms in my unit -about a 10% offset. Button 1 selects the slower speed with a longer delay time, but I did not measure this.

Regrettably, for you guys- I did not take notes on the final individual settings needed to exactly replicate the Dimension D sound, but it is possible to get very very close. I really just used this as an exercise to see whether it could actually be done, and to glean information to use in creating, and fine tuning my own definitive chorus. The Dimension D is fantastic, but not perfect for everything as it adds its own colour. Doing all this also confirmed my opinion that the Ultra is possibly the best and most versatile processor available at the moment.

There it is. I hope this helps you Roland chorus nuts out there to nail the ‘D’ sound.

Best Wishes Everyone….

Wide guitars with mono compatibility

This section is only relevant for recording - it is irrelevant for playing live.

If you normally add a stereo chorus to a dry signal, you have three guitars in the mix: One (dry) in the middle, two on right and left. Sometimes you just want to pan a guitar to left and right without endangering mono-compatibility, and without a middle guitar, so you don't occupy the space where the voice is.

This is how you do it:

  • Split the signal, one goes into a shunt, one into the chorus.
  • Set the chorus to 100% wet.
  • Combine both signals with a mixer.
  • In the mixer, pan the dry signal to the left, the chorus to the right.
  • Adjust the rate and the depth of the chorus to taste.