Difference between revisions of "Amp simulator"

From Fractal Audio Wiki
Jump to navigation Jump to search
(added SAG "off" description)
 
(28 intermediate revisions by 10 users not shown)
Line 2: Line 2:
 
Without distortion the electric guitar probably wouldn't have had nearly the impact it has had on popular music. The [[Axe-Fx]] contains multiple distortions based on emulations of various amplifiers. As mentioned earlier the Axe-Fx is not a modeler however these emulations provide sonic characteristics very similar to the amplifier they are emulating.  
 
Without distortion the electric guitar probably wouldn't have had nearly the impact it has had on popular music. The [[Axe-Fx]] contains multiple distortions based on emulations of various amplifiers. As mentioned earlier the Axe-Fx is not a modeler however these emulations provide sonic characteristics very similar to the amplifier they are emulating.  
  
One of the primary differences between the Axe-Fx and a modeling amplifier is the control philosophy. Modeling amps replicate the operation of the tone, volume, drive, etc. controls even replicating the annoying interaction among these controls. The Axe-Fx philosophy is to provide the control as a more useful tool rather than a strict replica of the original. In this regard the tone controls on the Axe-Fx are true cut/boost equalizing controls and do not interact. Because of this the controls are more powerful and are set differently than on a typical amplifier. "Diming" all the tone controls may sound great on an old tube amp but usually gives less the optimum results with the Axe-Fx.  
+
One of the primary differences between the Axe-Fx and a modeling amplifier is the control philosophy. Modeling amps replicate the operation of the tone, volume, drive, etc. controls even replicating the annoying interaction among these controls. The Axe-Fx philosophy is to provide the control as a more useful tool rather than a strict replica of the original. In this regard the tone controls on the Axe-Fx are true cut/boost equalizing controls and do not interact. Because of this the controls are more powerful and are set differently than on a typical amplifier. "Diming" all the tone controls may sound great on an old tube amp but usually gives less than optimum results with the Axe-Fx.  
  
 
The Axe-Fx distortion is based on a proprietary dual-stage non-linearity generator. There are two basic stages: preamplifier and power amplifier. The preamplifier stage emulates the distortion generated by classic tube preamplifiers. The power amplifier stage emulates the type of distortion generated by a tube power amplifier using our proprietary Dynamic Response TechnologyTM.  
 
The Axe-Fx distortion is based on a proprietary dual-stage non-linearity generator. There are two basic stages: preamplifier and power amplifier. The preamplifier stage emulates the distortion generated by classic tube preamplifiers. The power amplifier stage emulates the type of distortion generated by a tube power amplifier using our proprietary Dynamic Response TechnologyTM.  
Line 10: Line 10:
  
 
====Parameters====
 
====Parameters====
*'''TYPE''' - Selects the amplifier simulation. The simulations are based on classic and modern amps as well as some hybrids and completely original types that we concocted. The following types are available:
+
*'''GLOBL''' - If set to OFF the amp block works as normal. If set to GLOBAL1 through GLOBAL10, the amp will load the parameters from a "global amp parameter list". This parameter allows you to have 10 amps, each with different customizable settings, available to use in any preset.
**'''Tube Pre'''  - A completely neutral, low-gain tube pre-amp simulation. Useful for warming up vocals and other instruments.
+
*'''TYPE''' - Selects the amplifier simulation. The simulations are based on classic and modern amps as well as some hybrids and completely original types that we concocted. Check [[List_of_amp_simulations | this page in the Wiki]].
**'''Jazz'''  - Based on a Japanese solid-state amp with built-in chorus. With essentially no tone shaping this amp has a warm, midrange-thick sound that is good for jazz and fingerstyle. With the Axe-Fx’s powerful tone controls you can tweak this type to get shimmering rhythm tones as well.
 
**'''Brownface'''  - Based on a classic American 40-watt tube amp with built-in vibrato. Great for gutsy blues, this type breaks up nicely, especially when the Master is cranked. The original had no Mid or Presence so set these to ‘0’ for classic tone.
 
**'''Blues'''  - A low-to-medium gain sound great for blues. Based on a classic bass amplifier with four 10” speakers, it didn’t work so well for bass but guitar players quickly discovered it made a great blues amp. Try a treble booster in front for screaming blues work a la Albert Collins or Albert King.
 
**'''Tweed'''  - Based on a small, low-power, tweed-covered amp. The original had no controls other than volume. Set all tone controls to ‘0’ for authentic tone. Adjust as desired to venture into new sonic territory. Our simulation has a bit more gain than the somewhat anemic original to allow you to dial in a nice crunch. To recreate the original faithfully set the drive to about 6 and use the Master as the volume.
 
**'''Blackface'''  - Based on a popular, 100-watt American tube amp with two 12” speakers. This simulation captures the Normal Channel. Very similar to the Brownface model but a little more mellow. The tone-stack is also slightly different giving it just a bit different voicing.
 
**'''Class A'''  - A medium-gain emulation based on an early British tube amplifier. This type does not have the high-frequency emphasis like the American types and therefore has a darker sound. Try a treble boost in front for a snarling British “opera-rock” sound. This amp is notable in that it has no negative feedback around the power-amp and hence has a gritty character and less high-frequency response.
 
**'''Top Boost''' - Based on the “Top Boost Mod” version of the Class A. The public yearned for a brighter amp and the designers responded by adding a treble boost circuit. At first this circuit was a retrofit but then included as standard. Our simulation captures the boosted high-frequency response and slightly reduced bass response of the original.
 
**'''Plexi'''  - Based on a classic British amp, the Plexi is great for crunchy rhythm work. The original was basically a copy of the 4x10 bass amp (see Blues type above) that guitar players adopted but with EL34 output tubes and other British components. Despite being essentially a copy it had a unique voice all its own. It has somewhat low preamp gain and works best with the Master and Drive both set fairly high.
 
**'''Brit 800'''  - The successor to the Plexi type was the vaunted 800 series lead amplifier. Many 80’s rock hits were born using this amp and we’ve captured its tone and put it into a neat little package. This amp had EL34 output tubes, some treble peaking on the input and a little more gain than the Plexi. Like the Plexi type it likes having the Master cranked. At low Master settings the amp can be brittle but bring the Master up and the true tone of this beast comes out. Try it with any of the 4x12 cabinet types for classic rock and metal tones. Try a drive block in front for more snarl.
 
**'''Brit 900'''  - The successor to the 800 series was the 900 series. This amp had basically the same power amp but a new preamp with more tone shaping, more gain, and a solid-state clipping circuit that gave it a raspier sound. This amp was designed to get more of it’s distortion from the preamp than the earlier models but you can still keep the drive low and turn up the Master for more power amp distortion.
 
**'''Brown'''  - Based on a modified British style head with plenty of gain and lots of mids and highs. This type captures the sound of Eddie’s early work. Crank the Master and bring the drive up until you reach sonic nirvana.
 
**'''Boutique 1''' - A medium-gain, thick, yet crisp, sound with a fair amount of power amp breakup. Based on a now-defunct amplifier that was renowned for it’s liquid tone and endless sustain. This amp had very unique tone controls and as a result a distinctive voice with a bell-like quality. The preamp gain is fairly low so crank the Master to get that gutsy crunch. Good for rhythm work in a sparse situation where fullness of tone is required.
 
**'''Boutique 2''' - Same as Boutique 1 but with more gain and a bit more high- frequency emphasis. The lead version of Boutique 1.
 
**'''HiPower I''' - A medium-gain, full sound based on a famous “High Wattage” amp. These amps had a unique tone-stack and industrial quality output transformers with tremendous frequency response. Chimey with a bit of power amp breakup. Plug in your Tele and crank out some Baba O'Reilly.
 
**'''HiPower II''' - Like HiPower I but using the “Brilliant” channel.
 
**'''USA Clean'''  - A somewhat neutral clean sound that can pushed into gentle clipping. Based on a classic California amp’s clean channel this type has a full tone with a gentle midrange dip. The power amp is punchy and clean but can be driven into light distortion if desired. Sounds best with the drive turned up fairly high.
 
**'''USA Rhy 1''' - Crunchy California rhythm sound. Effective for solo use too with the gain turned up.
 
**'''USA Rhy 2''' - Similar to USA Rhy 1 but with the “mid-boost” engaged. This effectively removes the midrange dip from the tone stack and gives a more focused sound and a bit more gain.
 
**'''USA Lead 1''' - A tight, focused, hi-gain sound great for fusion and rock leads. Based on a modern Californian lead amp that set the standard for hi-gain lead tones. With the tone-stack before the preamp tubes this type has a more liquid response than the British types where the tone-stack is after the preamp. For the classic California lead sound turn the drive up and back off the Master a bit so that most of the distortion is coming from the preamp.
 
**'''USA Lead 2''' - Similar to USA Lead I but with the “treble shift” engaged. This shifts the response of the treble control lower and gives a slightly different character to the tone. There is also a “treble peaker” on the input stage which slightly boosts the high frequencies giving this type a little more “cut”.
 
**'''Recto 1''' - Based on a diamond-plated monster that redefined hard rock and “nu-metal” this type is characterized by a big bottom and some top-end sizzle. The tone-stack location is after the preamp which is quite a departure from the earlier Californian amplifiers.
 
**'''Recto 2''' - Similar to Recto I but with a slightly different input frequency shaping circuit.
 
**'''Solo 100''' - Based on a high-gain hot-rod with a chrome chassis, this amp is noted for it’s snarling lead sound. Also great for aggressive rhythm work, this type “chugs” nicely without getting muddy. Pair it with one of the 4x12 cabinet simulations for modern rock tones.
 
**'''Spec. OD 1''' - Based on a coveted but rare lead head that was made famous by Larry Carlton and others. Another amp with a very strange tone-stack, this amp has a singing voice and is great for modern blues/fusion work. This is the clean channel.
 
**'''Spec OD 2''' - The overdrive channel of the above.
 
**'''Euro 1'''  - Based on a German high-gain amp, these amps pay homage to the British amps but with lots more gain and more high-frequency emphasis. This type simulates the overdrive channel with the boost and “structure” switches off.
 
**'''Euro 2'''  - As above but with the boost and structure switches on. This one has lots of gain and plenty of low-end chunk along with a crispy top-end. Great for modern metal.
 
**'''UK GC30''' - Based on a great British amp introduced in the 90’s this amp is a strange marriage of a USA style pre-distortion tone-stack, British voicing and a Class A power amp. Best for blues and lower-gain rock leads, has nice sustain qualities. Can get muddy at high drive levels, decrease the bass to compensate.  
 
**'''Buttery''' - Based on an 18-watt amp that gained notoriety during the late 90’s this type is a low-gain amp that relies mostly on power amplifier distortion. Try a drive in front for smooth lead sounds.
 
**'''Metal'''  - A custom type similar to a British type but with more gain for more grind. This simulation features quite a bit of high-frequency emphasis along with a modified British tone-stack. Capable of searing rhythm and lead tones.
 
**'''Big Hair'''  - Spandex, studded wrist bands, pyrotechnics and your Axe-Fx are all you'll need to relive the 80's metal scene. This custom type has a unique voicing and tone-stack that emphasizes mid frequencies without getting muddy. Now plug in and shred!
 
**'''Hellbeast'''  - A radical custom type with an unconventional tone-stack.
 
**'''Supertweed'''  - Like a vintage Tweed amplifier on steroids.
 
**'''Fusion'''  - A smooth, thick tone good for fusion/blues solo work.
 
**'''FAS Clean'''  - Combines the best features of the Blackface and the USA Clean into a hybrid clean tone that’s great for a variety of uses.
 
**'''FAS Crunch'''  - A hybrid British/USA crunch sound.
 
**'''FAS Lead 1''' - A neutral high gain lead with a tight midrange.
 
**'''FAS Lead 2''' - More gain and more sizzle.
 
**'''FAS Modern''' - A high gain hybrid tone that’s equally suited to modern rhythm and lead work.
 
**'''JR Blues''' - Based on a modern all-tube combo amp with two EL84 output tubes and a single 12” speaker. This amplifier has become an instant classic because of its gutsy tone at manageable volumes.
 
**'''Brit Pre''' - Based on a rack-mount preamplifier version of the '''Brit 900'''. The preamp gained notoriety for its crunchy tone and was made popular by ZZ Top.
 
**'''Recto New''' - Based on the modern version of the Recto 1 and Recto 2 amps. Some minor circuit changes made this version slightly more aggressive than the originals.
 
**'''German LD1''' - Based on a very high-gain German amplifier. Lots of bass, great for aggressive, drop-tuned riff work.
 
 
*'''BRIGHT''' - Many amplifiers contain a “treble peaker” on the volume or drive control (see '''DRIVE''' below). Some amplifiers have a “bright switch” that can be used to engage or disengage the circuit. On many amps this switch is built in to the volume control as a “pull on” switch. On others the circuit is hard-wired. <br>The Axe-Fx amp types default to a particular state for the bright switch. If the amp had a hard-wired treble peaker the default state is on. If the amp had no circuit at all the default state is off. You many override this state by selecting the '''TREB''' control and pressing '''ENTER'''. This will toggle the state of the switch. The text “BRIGHT” will appear under the control when the bright circuit is active. <br>If the original amp did not have a treble peaker circuit, the bright switch uses circuit values most suited to an amp of that type. On some amps the effect may be subtle, on others, quite pronounced.  
 
*'''BRIGHT''' - Many amplifiers contain a “treble peaker” on the volume or drive control (see '''DRIVE''' below). Some amplifiers have a “bright switch” that can be used to engage or disengage the circuit. On many amps this switch is built in to the volume control as a “pull on” switch. On others the circuit is hard-wired. <br>The Axe-Fx amp types default to a particular state for the bright switch. If the amp had a hard-wired treble peaker the default state is on. If the amp had no circuit at all the default state is off. You many override this state by selecting the '''TREB''' control and pressing '''ENTER'''. This will toggle the state of the switch. The text “BRIGHT” will appear under the control when the bright circuit is active. <br>If the original amp did not have a treble peaker circuit, the bright switch uses circuit values most suited to an amp of that type. On some amps the effect may be subtle, on others, quite pronounced.  
 
*'''DRIVE''' - Sets the preamp drive. Higher settings equal more preamp distortion. On some amplifier types the drive control has a treble peaker (like the original). When the drive is turned down the low frequencies are attenuated more than the high. As the drive is turned up the low frequencies are increased more. <br>Many amplifiers have this feature and it can be heard as the drive is varied. You can use this to achieve the exact sound you’re looking for when a drive block feeds the amp. Adjust the drive control of the amp to achieve the desired amount of input treble peaking and then adjust the drive and the output level of the drive block to achieve the desired amount of distortion. <br>The Drive control has 40 dB of range. At a setting of ‘0’ the gain is 40 dB below the maximum gain.
 
*'''DRIVE''' - Sets the preamp drive. Higher settings equal more preamp distortion. On some amplifier types the drive control has a treble peaker (like the original). When the drive is turned down the low frequencies are attenuated more than the high. As the drive is turned up the low frequencies are increased more. <br>Many amplifiers have this feature and it can be heard as the drive is varied. You can use this to achieve the exact sound you’re looking for when a drive block feeds the amp. Adjust the drive control of the amp to achieve the desired amount of input treble peaking and then adjust the drive and the output level of the drive block to achieve the desired amount of distortion. <br>The Drive control has 40 dB of range. At a setting of ‘0’ the gain is 40 dB below the maximum gain.
*'''BOOST''' - adds an additional 12db of gain for added preamp distortion. You many toggle this state by selecting the '''DRIVE''' control and pressing '''ENTER'''. This will toggle the state of the switch. The text “BOOST” will appear under the control when the boost circuit is active.
+
*'''BOOST''' - adds an additional 12db of gain for added preamp distortion. You many toggle this state by selecting the '''TYPE''' control and pressing '''ENTER'''. This will toggle the state of the switch. The text “BOOST” will appear under the control when the boost circuit is active.
*'''BASS, MID, TREB''' - Tone controls. The tone controls in the Axe-Fx have up to twice the range of a typical amplifier. When a tone control is set to the 12:00 position (0.0 dB) it is equivalent to the simulated amplifiers control at 12:00. However, the boost cut range of the control is greater, +/- 12 dB, whereas a typical amplifier may have only +/- 6 dB or less. This allows you to get sounds, like heavily scooped mids or boosted treble, that normally wouldn't be possible. <br>Also, the tone controls do not interact like a typical amplifier. So when you turn the treble control the midrange and bass are not affected. This makes dialing in a certain tone easier and quicker than with a typical tone stack. This does not affect the voicing of the simulation in that the frequency response of the original circuit is always achieved however the exact setting of the controls will be somewhat different. In general the Axe-Fx tone controls are more sensitive than a typical amp and require less extreme settings to achieve the same sound. For example, if you set the treble to full on a British hi-gain amp, the corresponding setting on the Axe-Fx is about 5.0 dB. The advantage of this philosophy is ease of use plus more flexibility and wider range of tones. Adjust the tone controls slowly and listen carefully. A 1.0 dB adjustment can make a marked difference in the tone. <br>Some of the amps simulated do not have the full complement of tone controls. In those cases setting the control to 12:00 replicates the original. For example, some early amps did not have Mid controls. To capture the original faithfully simply set the control to ‘0’. Adjust the control as desired to achieve new and different tones. <br>Be careful in setting the tone controls as extreme settings along with high gain can cause pickup squealing or excessive noise.  
+
*'''BASS, MID, TREB''' - Tone controls. The active tone controls in the Axe-Fx have up to twice the range of a typical amplifier. When a tone control is set to the 12:00 position (0.0 dB) it is equivalent to the simulated amplifiers control at 12:00. However, the boost cut range of the control is greater, +/- 12 dB, whereas a typical amplifier may have only +/- 6 dB or less. This allows you to get sounds, like heavily scooped mids or boosted treble, that normally wouldn't be possible. Also, the active tone controls do not interact like a typical amplifier. So when you turn the treble control the midrange and bass are not affected. This makes dialing in a certain tone easier and quicker than with a typical tone stack. This does not affect the voicing of the simulation in that the frequency response of the original circuit is always achieved however the exact setting of the controls will be somewhat different. In general the Axe-Fx tone controls are more sensitive than a typical amp and require less extreme settings to achieve the same sound. For example, if you set the treble to full on a British hi-gain amp, the corresponding setting on the Axe-Fx is about 5.0 dB. The advantage of this philosophy is ease of use plus more flexibility and wider range of tones. Adjust the tone controls slowly and listen carefully. A 1.0 dB adjustment can make a marked difference in the tone. For those who prefer the classic passive tone controls that are found on most tube amps, the Axe-Fx has the option of using this style of tone control as well. Not just a crude shelving filter approximation, the Axe-Fx passive tone stack simulation exactly replicates the frequency and phase response of the classic passive tone stack. When using the passive tone controls the display will read out in traditional 0-10 style as opposed to decibel readings. Some of the amps simulated do not have the full complement of tone controls. In those cases setting the control to 12:00 replicates the original. For example, some early amps did not have Mid controls. To capture the original faithfully simply set the control to ‘0’. Adjust the control as desired to achieve new and different tones. Be careful in setting the tone controls as extreme settings along with high gain can cause pickup squealing or excessive noise. This is especially true with the active controls.
 
*'''PRES''' - Power amp presence control. This control boosts (or cuts) the upper frequencies from the power amp simulator by varying the [[negative feedback]] frequency response. Increasing this can help your sound “cut” through a heavy mix. This control actually has a greater range than a standard presence control. Values greater than zero behave like a typical tube amp, values less than zero actually reduce the high-frequency response even further. <br>If the Damping is set to zero this control is converted to a high-shelf equalizer at the output of the power amp. This allows you to control the high-frequency response of the power amp for types that don’t have any negative feedback.
 
*'''PRES''' - Power amp presence control. This control boosts (or cuts) the upper frequencies from the power amp simulator by varying the [[negative feedback]] frequency response. Increasing this can help your sound “cut” through a heavy mix. This control actually has a greater range than a standard presence control. Values greater than zero behave like a typical tube amp, values less than zero actually reduce the high-frequency response even further. <br>If the Damping is set to zero this control is converted to a high-shelf equalizer at the output of the power amp. This allows you to control the high-frequency response of the power amp for types that don’t have any negative feedback.
 
*'''HI CUT''' - This control sets the cutoff frequency of a lowpass filter at the very end of the preamp simulation. It defaults to a preset value for each amp type but can be overridden if desired. Experiment with this to fine tune your tone. For example, some of the higher gain types are characterized by fairly heavy filtering after the preamp stage but with this control you can reduce the amount of filtering and achieve a brighter tone. Conversely you gain reduce this value to achieve a darker or less brittle tone. <br> If using the Axe-Fx along with a separate tube power amp you may wish to experiment with this control to achieve the desired tone as the power amp may have it’s own high-frequency filtering.  
 
*'''HI CUT''' - This control sets the cutoff frequency of a lowpass filter at the very end of the preamp simulation. It defaults to a preset value for each amp type but can be overridden if desired. Experiment with this to fine tune your tone. For example, some of the higher gain types are characterized by fairly heavy filtering after the preamp stage but with this control you can reduce the amount of filtering and achieve a brighter tone. Conversely you gain reduce this value to achieve a darker or less brittle tone. <br> If using the Axe-Fx along with a separate tube power amp you may wish to experiment with this control to achieve the desired tone as the power amp may have it’s own high-frequency filtering.  
 
*'''DEPTH''' - This controls the effective output impedance of the power amp simulation. Higher values increase the impedance which increases the interaction of the virtual speaker with the power amp. Higher values give a fuller, looser sound, while low values can be used to achieve a more focused sound.  
 
*'''DEPTH''' - This controls the effective output impedance of the power amp simulation. Higher values increase the impedance which increases the interaction of the virtual speaker with the power amp. Higher values give a fuller, looser sound, while low values can be used to achieve a more focused sound.  
*'''DEEP''' - Selecting the '''DEPTH''' control and then pressing '''ENTER''' toggles the state of the '''DEEP''' switch. When the '''DEEP''' switch is active the negative feedback around the power amp is modified and the power amp will have enhanced low-frequency response adding depth and punch to the tone. This control defaults to off whenever a new amp type is chosen.  
+
*'''DEEP''' - Power amp deep control. This control boosts the low frequencies from the power amp simulation by varying the negative feedback frequency response. Defaults to an appropriate value when the amp type is selected but may be overridden by the user.
 
*'''DAMP''' - This controls the amount of [[negative feedback]], or damping, in the power amp simulation. Higher values give a tighter and brighter sound but can sound harsh at very high master volume levels. Lower values give a loose and gritty sound and feel. Each amp type defaults to a its own value but you may override the default value with this control. For example, a Top Boost amp has no negative feedback and as a result a unique tonal character. You can override the default damping and dial in some negative feedback to give the power amp a more “American” sound but still retain the preamp voicing.  
 
*'''DAMP''' - This controls the amount of [[negative feedback]], or damping, in the power amp simulation. Higher values give a tighter and brighter sound but can sound harsh at very high master volume levels. Lower values give a loose and gritty sound and feel. Each amp type defaults to a its own value but you may override the default value with this control. For example, a Top Boost amp has no negative feedback and as a result a unique tonal character. You can override the default damping and dial in some negative feedback to give the power amp a more “American” sound but still retain the preamp voicing.  
*'''SAG''' - This controls how dynamic the power amp simulation behaves. Higher settings simulate higher power supply impedance and thus more droop in the tube plate voltages which leads to a more compressed feel. <br> This control interacts with the Master Volume control in that at low Master Volume settings this control will have little effect as the power amp is not being pushed. As the power amp is pushed and draws more virtual current from its virtual power supply the Sag control will have more effect. <br> ''NOTE: Turning this control fully CCW defeats the power amp simulation. If you are using the Axe-Fx into an external tube power amp and cabinet you may want to set this control to zero to defeat the power amp simulation.'' <noinclude>With the power amp sims off the depth and deep controls are deactivated. The master works as just a volume and the presence turns into a shelving filter.</noinclude>
+
*'''SAG''' - This controls how dynamic the power amp simulation behaves. Higher settings simulate higher power supply impedance and thus more droop in the tube plate voltages which leads to a more compressed feel. <br> This control interacts with the Master Volume control in that at low Master Volume settings this control will have little effect as the power amp is not being pushed. As the power amp is pushed and draws more virtual current from its virtual power supply the Sag control will have more effect. <br> ''NOTE: Turning this control fully CCW defeats the power amp simulation. If you are using the Axe-Fx into an external tube power amp and cabinet you may want to set this control to zero to defeat the power amp simulation.''  
 +
 
 +
<noinclude>With the power amp sims off the depth and deep controls are deactivated. The master works as just a volume and the presence turns into a shelving filter.</noinclude>
 
*'''MSTR VOL''' - This, the Master Volume, is a very important control. It determines the drive to the power amp simulator. A higher setting increases the distortion contributed by the power amp simulator. As the Master is turned up the entire character of the amp will change, just like the real thing. The tone controls will have less influence on the sound, and the sound will “bloom” more and be more touch sensitive. <br> By carefully balancing Drive and Master Volume you can achieve the tone you desire. Experiment with the two to achieve your ultimate tone. Sometimes the tone you desire may be mostly preamp based and as such turn the Drive up and the Master down. Other times the tone may be mostly from the power amp so crank the Master up and back off the Drive. Amps with negative feedback (damping greater than zero) tend to have a crunchier power amp distortion and this can even get raspy if driven too hard. This is due to the negative feedback attempting to linearize the power amp. The resulting transfer function is harsher at clipping than an amp with little or no feedback. You can experiment with the damping control and master volume to achieve the desired power amp distortion timbre.<br> If the Master Volume is set very high best results are usually achieved by reducing the drive control. Try setting the Master around 9 or so and then slowly bringing the drive up until the desired tone is achieved. At high Master settings less drive is usually required, especially for high-gain types. <br> Amp types that are designed for preamp distortion typically sound better with lower values of this control and too high of a value can make the tone muddy or excessively noisy. This includes the USA Lead types, SOLO 100 and others. Lower gain amps such as Plexi, Brownface, and others can benefit from higher settings as this can reduce the harshness of the amp. <br> If the power amp simulation is off (Sag at zero) this control then becomes a simple level control. This control has 40 dB of range. A setting of ‘5’ is therefore 20 dB less than maximum.  
 
*'''MSTR VOL''' - This, the Master Volume, is a very important control. It determines the drive to the power amp simulator. A higher setting increases the distortion contributed by the power amp simulator. As the Master is turned up the entire character of the amp will change, just like the real thing. The tone controls will have less influence on the sound, and the sound will “bloom” more and be more touch sensitive. <br> By carefully balancing Drive and Master Volume you can achieve the tone you desire. Experiment with the two to achieve your ultimate tone. Sometimes the tone you desire may be mostly preamp based and as such turn the Drive up and the Master down. Other times the tone may be mostly from the power amp so crank the Master up and back off the Drive. Amps with negative feedback (damping greater than zero) tend to have a crunchier power amp distortion and this can even get raspy if driven too hard. This is due to the negative feedback attempting to linearize the power amp. The resulting transfer function is harsher at clipping than an amp with little or no feedback. You can experiment with the damping control and master volume to achieve the desired power amp distortion timbre.<br> If the Master Volume is set very high best results are usually achieved by reducing the drive control. Try setting the Master around 9 or so and then slowly bringing the drive up until the desired tone is achieved. At high Master settings less drive is usually required, especially for high-gain types. <br> Amp types that are designed for preamp distortion typically sound better with lower values of this control and too high of a value can make the tone muddy or excessively noisy. This includes the USA Lead types, SOLO 100 and others. Lower gain amps such as Plexi, Brownface, and others can benefit from higher settings as this can reduce the harshness of the amp. <br> If the power amp simulation is off (Sag at zero) this control then becomes a simple level control. This control has 40 dB of range. A setting of ‘5’ is therefore 20 dB less than maximum.  
*'''LOWCUT FREQ''' - This control allows you to reduce the amount of low frequency content at the input to the amp simulator. This parameter defaults to a value for each type but can be overridden if desired.  
+
*'''LOWCUT FREQ''' - This control allows you to reduce the amount of low frequency content at the input to the amp simulator. This parameter defaults to a value for each type but can be overridden if desired. A higher value will "tighten" up the amp, since what a user calls "flub" is low frequency distortion.
 +
*'''Bright Cap''' - This control sets the value of the “bright cap” across the virtual drive control. Increasing this will make the preamp brighter and vice-versa. The Bright Switch must be engaged for the effect to be audible.
 +
*'''TONESTACK TYPE'''- This control allows you to select the type of tone stack used in the simulation. The tone stack will default to either '''ACTIVE''' or '''PASSIVE''' depending upon the '''DEFAULT TONESTK''' parameter in the '''GLOBAL''' menu. When set to '''ACTIVE''', the tone stack is a semi-parametric EQ with +/- 12 dB of range for each control. When set to '''PASSIVE''', the tone stack is an exact digital recreation of the classic tone stack used in the amplifier being simulated. You can also choose from a wide selection of other tone stacks if desired. Fifteen classic passive tone stacks are available to choose from. So you can dial up a Plexi model and change the tone stack to a Blackface or Top Boost, etc yielding hybrid amp sounds.
 +
*'''WARMTH'''-This controls the power tube and transformer interaction. Set to zero to deactivate. Increasing this value increases the apparent warmth and depth of the tone, especially as the power amp is driven harder. This parameter defaults to a non-zero value whenever a new amp type is chosen.
 +
*'''THUMP'''- This models the output transformer interaction with the speaker impedance.  The amount of thump is adjustable from 0 – 10.  Value is set to a default value when amp type is selected.  When using a tube power amp you may want to set this to zero as the tube power amp will produce it’s own thump.  To facilitate this the global power amp bypass has an additional mode that deactivates the thump modeling.
 
*'''TONE FREQ''' - This control allows you to alter the center frequency of the tone controls. You can use this to change the character of the preamp. This parameter defaults to a value for each type but can be overridden if desired.  
 
*'''TONE FREQ''' - This control allows you to alter the center frequency of the tone controls. You can use this to change the character of the preamp. This parameter defaults to a value for each type but can be overridden if desired.  
 +
*'''XFRMR MATCH''' - This controls the effective output impedance of the power amp simulation. Higher values increase the impedance which increases the interaction of the virtual speaker with the power amp. Higher values give a fuller, looser sound, while low values can be used to achieve a  more focused sound.
 
*'''XFORMER LF''' - This control allows you to alter the lower cutoff frequency of the “output transformer”. Increase this value to simulate an old, under-designed transformer as was common in some vintage amps. This parameter defaults to a value for each type but can be overridden if desired.  
 
*'''XFORMER LF''' - This control allows you to alter the lower cutoff frequency of the “output transformer”. Increase this value to simulate an old, under-designed transformer as was common in some vintage amps. This parameter defaults to a value for each type but can be overridden if desired.  
 
*'''XFORMER HF''' - This control allows you to alter the upper cutoff frequency of the “output transformer”. Decrease this value to simulate narrow bandwidth transformers as were common in some vintage amps. This parameter defaults to a value for each type but can be overridden if desired.  
 
*'''XFORMER HF''' - This control allows you to alter the upper cutoff frequency of the “output transformer”. Decrease this value to simulate narrow bandwidth transformers as were common in some vintage amps. This parameter defaults to a value for each type but can be overridden if desired.  
*'''TONE LOCATION''' - This control allows you to alter the location of the tone stack. “Pre” places the tone stack at the input to the amp, “post” places the stack between the preamp and power amp. This parameter defaults to a value for each type but can be overridden if desired.  
+
*'''TONE LOCATION''' - This control allows you to alter the location of the tone stack. “PRE” places the tone stack at the input to the amp, “POST” places the stack between the preamp and power amp. "END" places the tonestack after the power amp simulation. This parameter defaults to a value for each type but can be overridden if desired.
*'''PRESENCE FREQ''' - This control allows you to alter the center frequency of the presence control. This parameter defaults to a value for each type but can be overridden if desired.  
+
*'''PWR TUBE BIAS '''- This parameter can be used to fine-tune the virtual power tubes’ bias points.  A value of zero corresponds to full Class B operation.  A value of one corresponds to full Class A operation.  Values in between are therefore Class AB.  For traditional Class AB power amps (i.e. Marshall, Fender, etc.) a value of 0.35 is considered the “optimum” bias point.  For traditional Class A amps, (which aren’t really true Class A, i.e. Vox, Matchless, etc.) a setting of 0.75 corresponds to the typical bias value these amps are run at.  Lower values of bias increase the amount of crossover distortion, add “hair” to the sound and make the power amp more “explosive” since the transfer function slope increases with input level.  Higher values of bias yield less distortion, “rounder” sound, more linear response and a more compressed feel.  At high Master Volume settings the effect of bias may be subtle.  As the Master Volume is turned down the audible effect is more pronounced.  Increasing the Damping increases the linearity of the power amp and also serves to reduce the audible effect of the bias control.
 +
*'''PRESENCE FREQ''' - This control allows you to alter the center frequency of the presence control. This parameter defaults to a value for each type but can be overridden if desired.
 +
*'''B+ CAPACITANCE''' - This control allows you to alter the amount of filtering capacitance on the power amp virtual power supply. Higher values will make the response stiffer and “faster”. Lower values will give a looser feel. Use along with the SAG control to fine-tune the response.
 +
*'''SPKR RES FREQ''' - This control allows adjustment of the virtual speaker impedance's resonance frequency. It defaults to the value of the cabinet that would typically be paired with the '''TYPE''', but can be adjusted to retune the response.  This control has the most effect when the Depth controls is fairly high (as depth controls the amp output impedance).
 +
*'''STABILIZER''' - Under certain extreme settings of '''DEPTH''' and '''DAMP''' the simulation may go unstable. This would happen in a real amplifier as well. The '''STABILIZER''' switch alters the “grid capacitor” values to ensure stability.  (Alternatively you can reduce the '''XFORMER LF''' value. This will usually remove any instability, although occasionally it won't. In those cases you can use the '''STABILIZER'''.)
 
*'''LEVEL, PAN, BYP MODE''' - These are the standard output mixer controls.  
 
*'''LEVEL, PAN, BYP MODE''' - These are the standard output mixer controls.  
 
  
 
<noinclude>
 
<noinclude>
Line 79: Line 46:
 
====Global amp====
 
====Global amp====
 
To use the global amp feature:
 
To use the global amp feature:
* Turn the GLOBL knob to select one of the ten 'Global Amps". Now make your adjustments: type, drive, etc.  
+
* Turn the GLOBL knob to select one of the ten 'Global Amps". As soon as you turn it from off it will load the parameters.
* Save the preset.  
+
Now make your adjustments: type, drive, etc. * Save the preset.  
 
* Now if you go to another preset and set the GLOBL to the same value all the values you saved with the previous preset are loaded.  
 
* Now if you go to another preset and set the GLOBL to the same value all the values you saved with the previous preset are loaded.  
* So any preset that uses the same Global Amp number will have the exact same parameter values. If you edit an amp block that uses a Global Amp and save the preset, all the other presets that use the same Global Amp will reflect those changes.  
+
* So any preset that uses the same Global Amp number will have the exact same parameter values. If you edit an amp block that uses a Global Amp and save the preset, all the other presets that use the same Global Amp will reflect those changes. For example, if you set an amp to GLOBAL2 and adjust that amp to be a Plexi model with various drive, bass, etc., anytime you recall a preset with the GLOBL set to GLOBAL2 that amp will use the same parameters.
 +
 
 +
 
 +
====Varying the drive/gain====
 +
{{:Varying drive}}
 +
 
 +
====Using different amp sims====
 +
{{main|Using different amp simulations}}
 +
The amp sims are based on real world designs and therefore have certain quirks and nuances like the amps they're based off of exhibit.  Take time to learn how different knobs, especially tone controls, react and possibly interact in the different sims.
 +
 
 +
====Imitating other amps====
 +
{{main| Amp imitation}}
 +
The advanced parameters can be used to tweak existing amp sims to emulate additional amplifier types with similar designs.
  
 +
====Tightening vintage amps====
 +
{{main|Tightening Vintage Amps}}
 +
The advanced parameters can be used to tighten up existing vintage amps sims.
  
 
====List of amp simulations====
 
====List of amp simulations====

Latest revision as of 01:15, 10 June 2010

Amp Simulator block.jpg

Without distortion the electric guitar probably wouldn't have had nearly the impact it has had on popular music. The Axe-Fx contains multiple distortions based on emulations of various amplifiers. As mentioned earlier the Axe-Fx is not a modeler however these emulations provide sonic characteristics very similar to the amplifier they are emulating.

One of the primary differences between the Axe-Fx and a modeling amplifier is the control philosophy. Modeling amps replicate the operation of the tone, volume, drive, etc. controls even replicating the annoying interaction among these controls. The Axe-Fx philosophy is to provide the control as a more useful tool rather than a strict replica of the original. In this regard the tone controls on the Axe-Fx are true cut/boost equalizing controls and do not interact. Because of this the controls are more powerful and are set differently than on a typical amplifier. "Diming" all the tone controls may sound great on an old tube amp but usually gives less than optimum results with the Axe-Fx.

The Axe-Fx distortion is based on a proprietary dual-stage non-linearity generator. There are two basic stages: preamplifier and power amplifier. The preamplifier stage emulates the distortion generated by classic tube preamplifiers. The power amplifier stage emulates the type of distortion generated by a tube power amplifier using our proprietary Dynamic Response TechnologyTM.

Full control over all parameters is naturally afforded allowing precise tailoring of this all-important block to your particular sonic tastes. Read the following carefully as the distortion block in the Axe-Fx is very sophisticated and a complete understanding will allow you to get the most from it. Also it is important to understand the role of the Cabinet Simulator in the overall sound. The cabinet contributes to the sound of a preset at least as much the amplifier type. If you’re not getting the exact sound you’re looking for try a different cabinet simulation. Of course there are no “rules” so there’s nothing preventing you from using a 10” blues cabinet with a high-gain amp simulation. Experimentation can lead to some unique and useful sounds.


Parameters

  • GLOBL - If set to OFF the amp block works as normal. If set to GLOBAL1 through GLOBAL10, the amp will load the parameters from a "global amp parameter list". This parameter allows you to have 10 amps, each with different customizable settings, available to use in any preset.
  • TYPE - Selects the amplifier simulation. The simulations are based on classic and modern amps as well as some hybrids and completely original types that we concocted. Check this page in the Wiki.
  • BRIGHT - Many amplifiers contain a “treble peaker” on the volume or drive control (see DRIVE below). Some amplifiers have a “bright switch” that can be used to engage or disengage the circuit. On many amps this switch is built in to the volume control as a “pull on” switch. On others the circuit is hard-wired.
    The Axe-Fx amp types default to a particular state for the bright switch. If the amp had a hard-wired treble peaker the default state is on. If the amp had no circuit at all the default state is off. You many override this state by selecting the TREB control and pressing ENTER. This will toggle the state of the switch. The text “BRIGHT” will appear under the control when the bright circuit is active.
    If the original amp did not have a treble peaker circuit, the bright switch uses circuit values most suited to an amp of that type. On some amps the effect may be subtle, on others, quite pronounced.
  • DRIVE - Sets the preamp drive. Higher settings equal more preamp distortion. On some amplifier types the drive control has a treble peaker (like the original). When the drive is turned down the low frequencies are attenuated more than the high. As the drive is turned up the low frequencies are increased more.
    Many amplifiers have this feature and it can be heard as the drive is varied. You can use this to achieve the exact sound you’re looking for when a drive block feeds the amp. Adjust the drive control of the amp to achieve the desired amount of input treble peaking and then adjust the drive and the output level of the drive block to achieve the desired amount of distortion.
    The Drive control has 40 dB of range. At a setting of ‘0’ the gain is 40 dB below the maximum gain.
  • BOOST - adds an additional 12db of gain for added preamp distortion. You many toggle this state by selecting the TYPE control and pressing ENTER. This will toggle the state of the switch. The text “BOOST” will appear under the control when the boost circuit is active.
  • BASS, MID, TREB - Tone controls. The active tone controls in the Axe-Fx have up to twice the range of a typical amplifier. When a tone control is set to the 12:00 position (0.0 dB) it is equivalent to the simulated amplifiers control at 12:00. However, the boost cut range of the control is greater, +/- 12 dB, whereas a typical amplifier may have only +/- 6 dB or less. This allows you to get sounds, like heavily scooped mids or boosted treble, that normally wouldn't be possible. Also, the active tone controls do not interact like a typical amplifier. So when you turn the treble control the midrange and bass are not affected. This makes dialing in a certain tone easier and quicker than with a typical tone stack. This does not affect the voicing of the simulation in that the frequency response of the original circuit is always achieved however the exact setting of the controls will be somewhat different. In general the Axe-Fx tone controls are more sensitive than a typical amp and require less extreme settings to achieve the same sound. For example, if you set the treble to full on a British hi-gain amp, the corresponding setting on the Axe-Fx is about 5.0 dB. The advantage of this philosophy is ease of use plus more flexibility and wider range of tones. Adjust the tone controls slowly and listen carefully. A 1.0 dB adjustment can make a marked difference in the tone. For those who prefer the classic passive tone controls that are found on most tube amps, the Axe-Fx has the option of using this style of tone control as well. Not just a crude shelving filter approximation, the Axe-Fx passive tone stack simulation exactly replicates the frequency and phase response of the classic passive tone stack. When using the passive tone controls the display will read out in traditional 0-10 style as opposed to decibel readings. Some of the amps simulated do not have the full complement of tone controls. In those cases setting the control to 12:00 replicates the original. For example, some early amps did not have Mid controls. To capture the original faithfully simply set the control to ‘0’. Adjust the control as desired to achieve new and different tones. Be careful in setting the tone controls as extreme settings along with high gain can cause pickup squealing or excessive noise. This is especially true with the active controls.
  • PRES - Power amp presence control. This control boosts (or cuts) the upper frequencies from the power amp simulator by varying the negative feedback frequency response. Increasing this can help your sound “cut” through a heavy mix. This control actually has a greater range than a standard presence control. Values greater than zero behave like a typical tube amp, values less than zero actually reduce the high-frequency response even further.
    If the Damping is set to zero this control is converted to a high-shelf equalizer at the output of the power amp. This allows you to control the high-frequency response of the power amp for types that don’t have any negative feedback.
  • HI CUT - This control sets the cutoff frequency of a lowpass filter at the very end of the preamp simulation. It defaults to a preset value for each amp type but can be overridden if desired. Experiment with this to fine tune your tone. For example, some of the higher gain types are characterized by fairly heavy filtering after the preamp stage but with this control you can reduce the amount of filtering and achieve a brighter tone. Conversely you gain reduce this value to achieve a darker or less brittle tone.
    If using the Axe-Fx along with a separate tube power amp you may wish to experiment with this control to achieve the desired tone as the power amp may have it’s own high-frequency filtering.
  • DEPTH - This controls the effective output impedance of the power amp simulation. Higher values increase the impedance which increases the interaction of the virtual speaker with the power amp. Higher values give a fuller, looser sound, while low values can be used to achieve a more focused sound.
  • DEEP - Power amp deep control. This control boosts the low frequencies from the power amp simulation by varying the negative feedback frequency response. Defaults to an appropriate value when the amp type is selected but may be overridden by the user.
  • DAMP - This controls the amount of negative feedback, or damping, in the power amp simulation. Higher values give a tighter and brighter sound but can sound harsh at very high master volume levels. Lower values give a loose and gritty sound and feel. Each amp type defaults to a its own value but you may override the default value with this control. For example, a Top Boost amp has no negative feedback and as a result a unique tonal character. You can override the default damping and dial in some negative feedback to give the power amp a more “American” sound but still retain the preamp voicing.
  • SAG - This controls how dynamic the power amp simulation behaves. Higher settings simulate higher power supply impedance and thus more droop in the tube plate voltages which leads to a more compressed feel.
    This control interacts with the Master Volume control in that at low Master Volume settings this control will have little effect as the power amp is not being pushed. As the power amp is pushed and draws more virtual current from its virtual power supply the Sag control will have more effect.
    NOTE: Turning this control fully CCW defeats the power amp simulation. If you are using the Axe-Fx into an external tube power amp and cabinet you may want to set this control to zero to defeat the power amp simulation.

With the power amp sims off the depth and deep controls are deactivated. The master works as just a volume and the presence turns into a shelving filter.

  • MSTR VOL - This, the Master Volume, is a very important control. It determines the drive to the power amp simulator. A higher setting increases the distortion contributed by the power amp simulator. As the Master is turned up the entire character of the amp will change, just like the real thing. The tone controls will have less influence on the sound, and the sound will “bloom” more and be more touch sensitive.
    By carefully balancing Drive and Master Volume you can achieve the tone you desire. Experiment with the two to achieve your ultimate tone. Sometimes the tone you desire may be mostly preamp based and as such turn the Drive up and the Master down. Other times the tone may be mostly from the power amp so crank the Master up and back off the Drive. Amps with negative feedback (damping greater than zero) tend to have a crunchier power amp distortion and this can even get raspy if driven too hard. This is due to the negative feedback attempting to linearize the power amp. The resulting transfer function is harsher at clipping than an amp with little or no feedback. You can experiment with the damping control and master volume to achieve the desired power amp distortion timbre.
    If the Master Volume is set very high best results are usually achieved by reducing the drive control. Try setting the Master around 9 or so and then slowly bringing the drive up until the desired tone is achieved. At high Master settings less drive is usually required, especially for high-gain types.
    Amp types that are designed for preamp distortion typically sound better with lower values of this control and too high of a value can make the tone muddy or excessively noisy. This includes the USA Lead types, SOLO 100 and others. Lower gain amps such as Plexi, Brownface, and others can benefit from higher settings as this can reduce the harshness of the amp.
    If the power amp simulation is off (Sag at zero) this control then becomes a simple level control. This control has 40 dB of range. A setting of ‘5’ is therefore 20 dB less than maximum.
  • LOWCUT FREQ - This control allows you to reduce the amount of low frequency content at the input to the amp simulator. This parameter defaults to a value for each type but can be overridden if desired. A higher value will "tighten" up the amp, since what a user calls "flub" is low frequency distortion.
  • Bright Cap - This control sets the value of the “bright cap” across the virtual drive control. Increasing this will make the preamp brighter and vice-versa. The Bright Switch must be engaged for the effect to be audible.
  • TONESTACK TYPE- This control allows you to select the type of tone stack used in the simulation. The tone stack will default to either ACTIVE or PASSIVE depending upon the DEFAULT TONESTK parameter in the GLOBAL menu. When set to ACTIVE, the tone stack is a semi-parametric EQ with +/- 12 dB of range for each control. When set to PASSIVE, the tone stack is an exact digital recreation of the classic tone stack used in the amplifier being simulated. You can also choose from a wide selection of other tone stacks if desired. Fifteen classic passive tone stacks are available to choose from. So you can dial up a Plexi model and change the tone stack to a Blackface or Top Boost, etc yielding hybrid amp sounds.
  • WARMTH-This controls the power tube and transformer interaction. Set to zero to deactivate. Increasing this value increases the apparent warmth and depth of the tone, especially as the power amp is driven harder. This parameter defaults to a non-zero value whenever a new amp type is chosen.
  • THUMP- This models the output transformer interaction with the speaker impedance. The amount of thump is adjustable from 0 – 10. Value is set to a default value when amp type is selected. When using a tube power amp you may want to set this to zero as the tube power amp will produce it’s own thump. To facilitate this the global power amp bypass has an additional mode that deactivates the thump modeling.
  • TONE FREQ - This control allows you to alter the center frequency of the tone controls. You can use this to change the character of the preamp. This parameter defaults to a value for each type but can be overridden if desired.
  • XFRMR MATCH - This controls the effective output impedance of the power amp simulation. Higher values increase the impedance which increases the interaction of the virtual speaker with the power amp. Higher values give a fuller, looser sound, while low values can be used to achieve a more focused sound.
  • XFORMER LF - This control allows you to alter the lower cutoff frequency of the “output transformer”. Increase this value to simulate an old, under-designed transformer as was common in some vintage amps. This parameter defaults to a value for each type but can be overridden if desired.
  • XFORMER HF - This control allows you to alter the upper cutoff frequency of the “output transformer”. Decrease this value to simulate narrow bandwidth transformers as were common in some vintage amps. This parameter defaults to a value for each type but can be overridden if desired.
  • TONE LOCATION - This control allows you to alter the location of the tone stack. “PRE” places the tone stack at the input to the amp, “POST” places the stack between the preamp and power amp. "END" places the tonestack after the power amp simulation. This parameter defaults to a value for each type but can be overridden if desired.
  • PWR TUBE BIAS - This parameter can be used to fine-tune the virtual power tubes’ bias points. A value of zero corresponds to full Class B operation. A value of one corresponds to full Class A operation. Values in between are therefore Class AB. For traditional Class AB power amps (i.e. Marshall, Fender, etc.) a value of 0.35 is considered the “optimum” bias point. For traditional Class A amps, (which aren’t really true Class A, i.e. Vox, Matchless, etc.) a setting of 0.75 corresponds to the typical bias value these amps are run at. Lower values of bias increase the amount of crossover distortion, add “hair” to the sound and make the power amp more “explosive” since the transfer function slope increases with input level. Higher values of bias yield less distortion, “rounder” sound, more linear response and a more compressed feel. At high Master Volume settings the effect of bias may be subtle. As the Master Volume is turned down the audible effect is more pronounced. Increasing the Damping increases the linearity of the power amp and also serves to reduce the audible effect of the bias control.
  • PRESENCE FREQ - This control allows you to alter the center frequency of the presence control. This parameter defaults to a value for each type but can be overridden if desired.
  • B+ CAPACITANCE - This control allows you to alter the amount of filtering capacitance on the power amp virtual power supply. Higher values will make the response stiffer and “faster”. Lower values will give a looser feel. Use along with the SAG control to fine-tune the response.
  • SPKR RES FREQ - This control allows adjustment of the virtual speaker impedance's resonance frequency. It defaults to the value of the cabinet that would typically be paired with the TYPE, but can be adjusted to retune the response. This control has the most effect when the Depth controls is fairly high (as depth controls the amp output impedance).
  • STABILIZER - Under certain extreme settings of DEPTH and DAMP the simulation may go unstable. This would happen in a real amplifier as well. The STABILIZER switch alters the “grid capacitor” values to ensure stability. (Alternatively you can reduce the XFORMER LF value. This will usually remove any instability, although occasionally it won't. In those cases you can use the STABILIZER.)
  • LEVEL, PAN, BYP MODE - These are the standard output mixer controls.


Global amp

To use the global amp feature:

  • Turn the GLOBL knob to select one of the ten 'Global Amps". As soon as you turn it from off it will load the parameters.

Now make your adjustments: type, drive, etc. * Save the preset.

  • Now if you go to another preset and set the GLOBL to the same value all the values you saved with the previous preset are loaded.
  • So any preset that uses the same Global Amp number will have the exact same parameter values. If you edit an amp block that uses a Global Amp and save the preset, all the other presets that use the same Global Amp will reflect those changes. For example, if you set an amp to GLOBAL2 and adjust that amp to be a Plexi model with various drive, bass, etc., anytime you recall a preset with the GLOBL set to GLOBAL2 that amp will use the same parameters.


Varying the drive/gain

The DRIVE control has too many calculations associated with it to allow a modifier to adjust it in real time. You can adjust gain in a preset in a few different ways, each with their own benefits and drawbacks. Recreating the effect of varying the DRIVE control has a certain set of needs that other techniques won't achieve.

Parallel paths: panning between inputs or mixing between outputs

Neither technique is going to be quite the same as simply adjusting a volume pedal to shift the gain. Panning between the inputs would better approximate this, but isn't much gained (pardon the unintended pun) by using a second setup then. For blending to a different tonality (such as boosted mids and smoother gain) for a solo though, that's a great approach.

Mixing between the outputs can be a nice effect, and useful for other things, but really isn't anywhere near the same as adjusting a gain control. If mixing between a signal and a version that's been pitch-shifted by an octave doesn't get a shift of a fifth. Similarly, gain structure isn't affected by mixing between low gain and high gain. It's a great way to clean up a really dirty sound to get more clarity, but not the same as turning down the distortion.

To think through this stuff, just think about what would happen if one channel was set to crystal clean and the other was a raging fuzz. Panning the inputs would simply fade out the clean while increasing the drive on the fuzz, but there would still be just a blend in the middle of the spectrum. (Again, not bad, just not riding the DRIVE control.) Mixing the outputs, you would just get more pick attack sticking through the fuzz. (Still useful; still not a variable DRIVE control.)

Volume block before the gain block

A volume (or null filter) block at the input of a Drive or Amp block is the way to go. You can set a range in the modifier so it varies between two set points. You can also throw a control at a LEVEL control somewhere further down the line (or another Volume block) to counteract (or further, if that's what you want) the volume boost from pushing everything further into saturation.

Using different amp sims

The amp sims are based on real world designs and therefore have certain quirks and nuances like the amps they're based off of exhibit. Take time to learn how different knobs, especially tone controls, react and possibly interact in the different sims.

Imitating other amps

Main article: Amp imitation

The advanced parameters can be used to tweak existing amp sims to emulate additional amplifier types with similar designs.

Tightening vintage amps

The advanced parameters can be used to tighten up existing vintage amps sims.

List of amp simulations

This is a list of the amps the Axe-Fx G1 models emulate, including their descriptions (manual and website), suggestions for matching cabinets and additional notes. The text in italics originates from the manual or website.

Pictures of some of the amps

Axe-Fx name Details of model
TUBE PRE = STUDIO TUBE PREAMP

This is a completely neutral, low-gain tube pre-amp simulation. Useful for warming up vocals and other instruments as well as direct guitar sound

  • Cabinet suggestion: n/a
  • Turn down Drive if the signal breaks up
JAZZ = ROLAND JAZZ CHORUS JC-120

This model is based on a 2x12 solid-state combo amp, known for its warm, midrange-thick sound and built-in stereo chorus

  • Cabinet suggestion: none. Alternative: Red Wirez JC-120
  • Original controls: Volume, Treble, Middle, Bass
  • Original manual
BROWNFACE = FENDER VIBROVERB

Our model is based on a 40W combo that's great for clear or grinding cleans and gutsy blues. This amp breaks up nicely, especially when the Master is cranked

  • Cabinet suggestion: 1x10 Gold. Alternative: Red Wirez Fender Dual Showman
  • Original controls (Normal channel): Volume (no Master), Bass/Treble, Bright switch (on by default). The real amp also has a Bright channel
  • For authentic clean tone: crank the Master, Drive at 3.50. For more crunch turn up Drive
  • Fender tips in the Wiki
  • Wikipedia
  • Fender Forum, The Fender Forum, FenderTalk, Fender
59 BASSGUY (formerly: BLUES) = FENDER BASSMAN

Model based on the Fender Bassman®, a low-to-medium gain amp designed for bass but more widely adopted by guitarists for its great blues and rock tones

DELUXE VERB (formerly: TWEED) = FENDER DELUXE REVERB (AB763)

Model based on a 1965 Fender Deluxe Reverb® 1x12 combo. This model has great chimey tone with nice power amp breakup when you push the MASTER

  • The former name "Tweed Deluxe" and description didn't match with the modeled amp. The name was changed to Deluxe Verb in firmware 9.01 and the amp was remodeled
  • Cabinet suggestion: 1x12 Tweed or 1x12 Black. Alternative: Red Wirez Fender Deluxe Reverb (Oxford speaker)
  • Original controls: Volume, Bass, Treble
  • For authentic tone: crank the Master, Drive at 3.50, Mid at 6.8
  • Fender tips in the Wiki
  • Wikipedia
  • Fender Forum, The Fender Forum, FenderTalk, Fender
DOUBLE VERB (formerly: BLACKFACE) = FENDER TWIN REVERB

Based on a blackface Fender Twin Reverb® 100-watt 2x12" combo, running the “Normal” channel. Known for amazing clean sounds it also breaks up very nicely

CLASS A = VOX AC30

Model based on the Vox AC30®, a combo that dominated the British Invasion sound. This model has the same gritty character, warm tone, and very playable feel

  • Cabinet suggestion: 1x12 or 2x12 Brit. Alternative: Red Wirez Vox, Red Wirez Blue, Ownhammer Blue
  • Original controls: Cut, Volume. Bright off by default. The original amp didn't have Bass, Middle and Treble controls, so leave them at noon and use Presence (= Cut) instead
  • Cliff: "An AC30 has no power amp feedback so it doesn't have presence or depth controls. It has a "Cut" control which is basically an adjustable snubber on the phase inverter. The Presence control becomes the Cut control. To duplicate the amp you would only adjust the Presence negative but the model lets you boost as well if you adjust Presence positive. The Depth control won't do anything so it doesn't matter where you set it. If the Damping (Damp) is zero the Depth control is disabled and Damp defaults to zero for that amp model"
  • For authentic tone: crank the Master, keep Drive low, keep the tone controls at noon, use Presence to cut the treble
  • Try with a Tonebender or Treble Booster Drive block. Try with the Plexi tonestack. Or try the AC30TB tone stack (Bright on)
  • Wikipedia
  • Vox forum
TOP BOOST = VOX AC30TBX TOPBOOST

Model based on the Vox AC30TBX® Top Boost, an amp created in response to demand for "More Treble". Great highs and slightly reduced bass

  • Cabinet suggestion: 1x12 or 2x12 Brit. Or use (or combine with) Marshall greenbacks (4x12 20w or 25w). Alternative: Red Wirez Vox and Marshall greenbacks, Ownhammer Blue and greenbacks
  • Original controls: Volume, Cut (= Presence control), Bass, Treble. Bright on by default.
  • For authentic tone: crank the Master, set Drive to taste, Mid at noon. Use Presence only to cut the high frequencies (left of noon)
  • Cliff: "An AC30 has no power amp feedback so it doesn't have presence or depth controls. It has a "Cut" control which is basically an adjustable snubber on the phase inverter. The Presence control becomes the Cut control. To duplicate the amp you would only adjust the Presence negative but the model lets you boost as well if you adjust Presence positive. The Depth control won't do anything so it doesn't matter where you set it. If the Damping (Damp) is zero the Depth control is disabled and Damp defaults to zero for that amp model"
  • Instead of turning up Drive, try boosting the input signal before the amp, for example with a Tape Drive or FET Boost Drive block
  • Another approach to get a Topboost tone: use the Class A sim, set its tonestack to AC30TB, switch on Bright (source: Scott Peterson)
  • Wikipedia
  • Vox forum
PLEXI 1 = MARSHALL SUPER LEAD (MODEL 1959 a.k.a. PLEXI)

Based on the classic British amp head that gave rise to the Marshall stack: the Super Lead Model 1959 Plexi. Great for crunchy rhythm work

  • Cabinet suggestion: 4x12 20w / 25w / Green. Alternative: Red Wirez Marshall greenbacks, Ownhammer greenbacks
  • Original controls: Volume, Bass, Middle, Treble. Presence on later models. Bright (Lead channel only) (on by default).
  • Crank the Master, set Drive high. Experiment with higher Sag settings
  • Because the bright cap (Lead channel) is very large, the Bright switch has a great impact on the amount of gain. Source
  • Cliff: "One of the first mods people make to real 'Plexi' Marshalls is to "clip the bright cap". The bright cap varied over the years, supposedly depending on what was lying around in the shop. The model defaults to the bright cap in the circuit. If you turn the bright off you're effectively clipping the bright cap. With the bright cap in Marshalls can be very bright and harsh. However, if you crank the Master you might find the extra brightness helps compensate for the power amp getting darker"
  • If the bass gets farty, turn up Low-Cut
  • Wiki: Bright switch
  • Wikipedia
  • MarshallForum
BRIT 800 = MARSHALL JCM800 (MODEL 2204)

Model based on the vaunted Marshall JCM800 (model 2204). Bring the Master up and the true 80s rock tone of this beast comes out

  • Cabinet suggestion: 4x12 V30, 4x12 20w / 25w /75w. Alternative: Red Wirez Marshall, Ownhammer
  • Original controls: Gain, Bass, Middle, Treble, Presence, Volume. bright cap (on by default).
  • For authentic tone: experiment with medium to high Master volume levels
  • The bright cap on the original (Lead channel) is tied to the pre-amp gain setting (Drive). If the amp is too bright on lower Drive setings, switch off Bright
  • Try with a TS808 or Tube Drive block, set the Drive block to zero Drive and full Level
  • Wikipedia
  • MarshallForum
BRIT 900 = MARSHALL JCM900

Based on the Marshall JCM900m this amp offers more tone shaping, more gain, and a solid-state clipping circuit for a raspier sound

  • Cabinet suggestion: 4x12 V30, 4x12 75w, 4x12 T75, 4x12 25w. Alternative: Red Wirez Marshall, Ownhammer
  • Original controls: Gain, Bass, Middle, Treble, Presence, Volume. Bright cap (on by default)
  • The bright cap on the original (Lead channel) is tied to the pre-amp gain setting (Drive). If the amp is too bright on low Drive setings, switch off Bright
  • Experiment with medium to high Master Volume levels
  • Try with a TS808 or Tube Drive block. Set the Drive block to zero Drive and full Level
  • Wikipedia
  • MarshallForum
BROWN = EDDIE VAN HALEN'S MODDED MARSHALL

A faithful recreation of the pure, raw (some might say erupting...) "Brown Sound" -- the signature tone of perhaps the best-known guitarist of the late '70s/'80s

  • Cabinet suggestion: 4x12 20w / 25w / Green. Alternative: Red Wirez Marshall greenbacks, Ownhammer greenbacks
  • Original controls: Volume, Bass, Middle, Treble. Bright (Lead channel, on by default)
  • For authentic tone: crank the Master Volume, turn up Drive. Or try the factory preset The Brown Sound
  • Because the bright cap (Lead channel) is very large, the Bright switch has a great impact on the amount of gain
  • Tip in the Wiki about the Bright switch
  • Wikipedia
  • MarshallForum
BOUTIQUE 1

BOUTIQUE 2

= MATCHLESS CHIEFTAIN: RHYTHM / LEAD

BOUTIQUE 1: Based on the Matchless Chieftain, known for its liquid tone and endless sustain -- a medium-gain amp, thick, yet crisp, with a fair amount of power amp breakup

BOUTIQUE 2: Also based on the Matchless Chieftain but with a boost engaged for more gain and high-frequency emphasis. Great for leads

  • Cabinet suggestion: 2x12 Boutique. Alternative: Red Wirez Matchless
  • Based on a Vox circuit
  • Original controls: Volume, Master Volume, Bass, Treble, Brilliance (Presence). No Mids
  • Keep Mid at noon. Turn up the Master Volume for crunchy leads
  • Tips in the Wiki
  • Original manual
  • Wikipedia
HIPOWER 1

HIPOWER 2

= HIWATT DR103: NORMAL / BRILLIANT CHANNEL

HIPOWER 1: Based on this medium-gain, full sound amp... unique tone-stack and a chimey grinding tone. Your ears may go numb (comfortably) with this one

HIPOWER 2: A brighter model based on the amp’s "Brilliant" channel. Who's next to to plug in to this inspired amp model?

  • Cabinet suggestion: none. Alternative: Red Wirez Fane
  • Original controls: Volume, Master, Bass, Middle, Treble and Presence
  • Dialing in the Hiwatt
  • Wikipedia
  • Cliff: " I have a 1974 Hiwatt DR-103. The model is based on that. It is one of the Harry Joyce, Hylight era models. Still has the original tubes. Closet find and sounds glorious."
USA CLEAN = MESA BOOGIE MKIV, CLEAN RHYTHM 1 CHANNEL

A somewhat neutral clean sounding model that can pushed into warm clipping. Based on a Mesa Boogie MKIV Rhythm 1 channel

  • Cabinet suggestion: 4x12 Cali. Alternative: Red Wirez Mesa, Ownhammer Mesa
  • Clean channel is based upon a Fender circuit
  • Turn up Drive, keep Master Volume low (3.50)
  • Original controls: Gain, Volume, Treble, Mid, Bass, Presence. Bright switch. Graphic Equalizer not modeled
  • John Petrucci settings
  • Original manual MKIV: detailed descriptions of the controls and sample settings
  • Tips in the Wiki
  • Wikipedia
  • Grailtone
USA RHY 1

USA RHY 2

= MESA BOOGIE MKIV, CRUNCH RHYTHM 2 CHANNEL: FAT SWITCH NOT ACTIVE / ACTIVE

USA RHY 1: A crunchy California rhythm sound based on a the Rhythm2 channel with the Mid Boost (“Fat”) switch OFF

USA RHY 2: Based on the MKIV Rhythm 2 channel, this time with the Mid Boost (“Fat”) switch ON for a more focused sound and a bit more gain

USA LEAD 1

USA LEAD 2

= MESA BOOGIE MKIV Lead: Treble Shift NO / YES

USA LEAD 1: This model has a tight, focused, hi-gain sound great for fusion and rock leads. Based on the Lead channel with the Treble Shift disengaged

USA LEAD 2: Based on a MKIV, the Treble Shift gives this amp a slightly different character with a little more cut

  • Cabinet suggestion: 4x12 Cali. Alternative: Red Wirez Mesa, Ownhammer Mesa
  • Original controls: Gain and Master, Bass/Middle/Treble, Presence (without/with treble shift), Bright switch. Graphic Equalizer not modeled
  • Treble Shift: this shifts the range of the Presence control to higher frequencies on the original amp, it influences the Treble control. In LEAD 1 Treble Shift is off, which works well for recording. In LEAD 2 Treble Shift is switched on, which works well within a band context, but can generate squealing and noise at high volume or gain levels
  • Turn up Drive, keep Master Volume low (3.50), don't use Bright on higher volume levels
  • John Petrucci settings
  • Original manual MKIV: detailed descriptions of the controls and sample settings
  • Tips in the Wiki
  • Wikipedia
  • Grailtone forum
RECTO ORANGE

RECTO RED

= MESA BOOGIE 2-CHANNEL DUAL RECTIFIER (OLD, SMALL LOGO): VINTAGE ORANGE CHANNEL (RHYTHM) / MODERN RED CHANNEL (LEAD)

RECTO ORANGE: Based on a the original Mesa Boogie 2-channel Dual Rectifier in the "Vintage" (Orange) channel (rhythm)

RECTO RED: Based on the Modern (Red) "Lead" channel, this is a high gain masterpiece with crushing power and tightness

  • The names and models changed from Recto 1 into Recto Orange and Recto 2 into Recto Red in 7.03, in firmware 7.03. (The manual still lists Recto 1 and 2)
  • Cabinet suggestion: 4x12 Recto1 or Recto2. Alternative: Red Wirez Mesa, Ownhammer Mesa
  • Original controls: Gain and Master, Bass/Middle/Treble, Presence. And probably a Bright peaker because the amp sim defaults to Bright on.
  • Turn up Drive, keep Master Volume low (3.50), keep Presence low
  • Recto Red defaults to no Damping, can be turned up
  • Cliff: "None of the Recto models in the Axe-Fx have the post tone-stack bass boost. If you want to replicate the behavior of a Single Rectifier you need to put an 11 dB bass boost after the preamp model. The Axe-Fx models are based on the Dual Rectifier modes with the bass boost switch off. Single Rectifiers engage the bass boost switch automatically in channel 2"
  • To mimick the bass boost, use a PEQ or low shelf Filter after the Amp block to boost bass by 11 dB at around 120Hz.
  • Original manual: detailed descriptions of the controls and sample settings
  • Video demo
  • Wikipedia
  • Grailtone forum
SOLO 100 = SOLDANO SUPER LEAD OVERDRIVE (SLO-100)

The SLO-100® is noted for its hot-rod chrome chassis, aggressive rhythm tone, and snarling lead sound

  • The Axe-Fx models the Overdrive channel
  • Cabinet suggestion: greenbacks (4x12 20w / 25w / green), G12H30 (4x12 30w), 4x12 Cali, EVL12. Alternative: Red Wirez Soldano (Eminence Legend), G12H30 or EVM12L. Or Ownhammer EVM12L or H75.
  • Original controls: Gain, Bass, Middle, Treble, Master, Presence. Bright switch (on the original amp only for Normal Channel)
  • Cliff: "The SLO100 is the loudest amp I've ever used. It feels like there's a small nuclear explosion going off inside when ever you hit a power chord. It's a wicked amp but not something I would recommend for anything but large gigs. If you like the SLO 100 model you might want to try the Recto models too. It's not widely known but the Rectifier preamp is a derivative of the SLO100. Some minor changes but the basic topology is identical"
  • Keep the Master volume low (3.50). It's a very bright amp, keep Presence and Treble low
  • Original manual
  • Soldano forum
  • Wikipedia
SPEC OD1

SPEC OD2

= DUMBLE OVERDRIVE SPECIAL: CLEAN / LEAD

SPEC OD1: Based on the Clean channel of a coveted but rare amp made famous by Robben Ford and Larry Carlton, among others

SPEC OD2: Based on this amp's foot-switchable Lead channel with great singing sustain and tone appropriate for modern blues, fusion, and more

  • Cabinet suggestion: 2x12 Custom
  • Original controls: Master, Bass, Middle, Treble. Bright switch
  • Wikipedia
EURO BLUE

EURO RED

= 20TH ANN. BOGNER ECSTASY (XTC): BLUE / RED CHANNEL

EURO BLUE: Based on the 20th Anniversary model, this amp type simulates the overdrive channel with the BOOST and STRUCTURE switches OFF

EURO RED: This is based on the Red Channel with BOOST and STRUCTURE switches ON. Lots of gain and plenty of low-end chunk along with a crispy top-end

  • In firmware 10.x the names have been changed from Euro 1 to Euro Blue, and from Euro 2 to Euro Red. The description for Euro Red in the manual and on the website hasn't been updated
  • Cabinet suggestion: 4x12 German. Alternative: Red Wirez Bogner, Ownhammer V30
  • Original controls: Gain and Master, Bass/Middle/Treble, Presence, Bright switch (off by default)
  • Euro Blue: the model is very low gain and dark. Try with Boost and Bright (or turn up Presence instead of Bright)
  • Euro Red: the model is very dark. Try Bright (or turn up Presence)
  • Quote Cliff: "My actual XTC has a Log10 pot for the treble which is an odd choice. Treble pots are usually linear and the Axe-Fx model uses a linear pot. The problem with a log-taper pot is that the treble does almost nothing for the first 50%. So you can't use your eyes if you want to copy the tone. This is the case with several of the amp models. In these cases the taper used on the real amp is what I would call "a less than optimum" choice. I think in many cases the designer simply doesn't realize the affect the taper has on the locus. So, if I deemed the choice of taper to be "incorrect" the model uses the correct taper. The Bogner models fall into this category. The choice of a Log10 pot for the treble pot doesn't make sense so the model uses a linear taper which gives a smooth locus"
  • Original manual
  • 20th Ann. specifications
  • Sample settings
  • Sound clips
  • Bogner Amp Forum
  • Wikipedia
UKGC30 = LANEY GC30V

Based on the marriage of a USA style pre-distortion tone-stack, British voicing and Class A power amp. Great for lower-gain leads with nice sustain qualities

  • Cabinet suggestion: none
  • Based on Vox AC30
  • Original controls: Drive, Bass, Middle, Treble, Volume. No Bright
  • Original manual
BUTTERY = BUDDA TWINMASTER

This model is loosely based on a late 90s Budda Twinmaster. A low gain amp, it relies mostly on power amp distortion. Try a drive in front for smooth lines

  • Cabinet suggestion: greenbacks (4x12 20w / 25w), 4x12 30w or something that resembles Eminence Legends
  • Original controls: Bass, Treble, Volume. Bright cap on the Volume control (Bright switch)
  • Turn up the Master volume, use Drive for volume and gain, turn down Bass (or turn up Low Cut)
  • Try a Drive block before the Amp
  • Cliff: "I did the Buttery model by ear. I listened to some clips of Buddas (Matchbox 20, remember them?) and tweaked the model until I thought it sounded like one. Screwed around a little with the tube bias points until it had the right balance of harmonics and called it a day"
  • Wikipedia
  • Budda Forum
  • Original manual
FAS METAL = FRACTAL AUDIO SYSTEMS: CUSTOM MODEL

A custom type similar to a JCM but with more gain and grind. This simulation features quite a bit of high- emphasis along with a modified British tone-stack

  • No equivalent original amplifier
  • Cabinet suggestion: 4x12 Marshall
FAS BIG HAIR = FRACTAL AUDIO SYSTEMS: CUSTOM MODEL

Spandex, studded wrist bands, pyrotechnics and this custom creation by Fractal Audio Systems are all you'll need to re-live the 80's metal scene

  • No equivalent original amplifier
  • Cabinet suggestion: 4x12 Marshall
FAS HELLBEAST = FRACTAL AUDIO SYSTEMS: CUSTOM MODEL

A radical custom amplifier model designed with an unconventional tone-stack by Fractal Audio Systems

  • No equivalent original amplifier
  • Cabinet suggestion: none
FAS SUPERTWEED = FRACTAL AUDIO SYSTEMS: CUSTOM MODEL

This model designed by Fractal is like a vintage Tweed amplifier on steroids

  • No equivalent original amplifier
  • Cabinet suggestion: Tweed
FAS FUSION = FRACTAL AUDIO SYSTEMS: CUSTOM MODEL

This model designed by Fractal Audio Systems has a smooth, thick tone good for fusion/blues solo work

  • No equivalent original amplifier
  • Cabinet suggestion: 2x12 Custom
FAS CLEAN = FRACTAL AUDIO SYSTEMS: CUSTOM MODEL

Combines the best features of the Blackface and the USA Clean models into a hybrid that's great for a variety of uses

  • No equivalent original amplifier
  • Cabinet suggestion: 1x12 or 2x12 Black
FAS CRUNCH = FRACTAL AUDIO SYSTEMS: CUSTOM MODEL

Combines the best features of the British and USA crunch models for grinding tones that are evocative and innovative at the same time

  • No equivalent original amplifier. Based on Mesa amp
  • Cabinet suggestion: Mesa (4x12 Recto1, Recto2 or Cali)
FAS LEAD 1 = FRACTAL AUDIO SYSTEMS: CUSTOM MODEL

A custom amp by Fractal Audio Systems, this model is a neutral high gain lead with a tight midrange

  • No equivalent original amplifier. Based on Mesa amp
  • Cabinet suggestion: Mesa (4x12 Recto1, Recto2 or Cali)
FAS LEAD 2 = FRACTAL AUDIO SYSTEMS: CUSTOM MODEL

A custom amp by Fractal Audio Systems, this model has more sizzle and gain the the FAS Lead I

  • No equivalent original amplifier. Based on Mesa amp
  • Cabinet suggestion: Mesa (4x12 Recto1, Recto2 or Cali)
FAS MODERN = FRACTAL AUDIO SYSTEMS: CUSTOM MODEL

A high gain hybrid model custom designed by Fractal Audio Systems. Equally well suited to modern rhythm and lead work

  • No equivalent original amplifier. Based on Mesa amp
  • Cabinet suggestion: Mesa (4x12 Recto1, Recto2 or Cali)
JR BLUES = FENDER BLUES JR

Based on a modern combo with two EL84s and a single 12" speaker. The original became an instant classic because of its gutsy tone at manageable volumes

BRIT PRE = MARSHALL JMP-1 PREAMP

Based on a rack-mount preamplifier version of the Brit 900. The preamp gained notoriety for its crunchy tone and was made popular by ZZ Top and Def Leppard

  • Cabinet suggestion: n/a
  • This sim uses the poweramp of the JMC800
  • The original preamp has two tubes inside
  • Original controls: Gain, Volume, Bass, Mid, Treble, Presence
  • Original manual
  • Wikipedia
  • MarshallForum
ENERGYBALL = ENGL POWERBALL, LEAD CHANNEL

Based on a very high-gain amplifier from Germany with lots of bass. Great for aggressive, drop-tuned riff work

  • Cabinet suggestion: 4x12 Metal. Alternative: Red Wirez Engl, Ownhammer V30
  • Original controls: Gain, Volume, Bass, Middle, Treble, Presence. Bright switch (Clean channel)
  • Original manual: sample settings
  • Wikipedia
RECTO NEW = MESA BOOGIE 3-CHANNEL DUAL RECTIFIER, RED "MODERN" CHANNEL

Based on the modern version of the Dual Rectifier amps. Circuit changes made this version more aggressive

  • Cabinet suggestion: 4x12 Recto1 or Recto2. Alternative: Red Wirez Mesa, Ownhammer Mesa
  • Original controls: Presence, Master, Gain, Bass, Middle, Treble. Bright cap probably because it's on by default
  • Keep Master volume low (3.50), use Drive to add gain
  • Cliff: "None of the Recto models in the Axe-Fx have the post tone-stack bass boost. If you want to replicate the behavior of a Single Rectifier you need to put an 11 dB bass boost after the preamp model. The Axe-Fx models are based on the Dual Rectifier modes with the bass boost switch off. Single Rectifiers engage the bass boost switch automatically in channel 2"
  • To mimick the bass boost, use a PEQ or low shelf Filter after the Amp block to boost bass by 11 dB at around 120Hz.
  • Original manual: detailed descriptions of the controls and sample settings
  • Tips in the Wiki
  • Wikipedia
  • Grailtone forum
HAD ODS 1 = DUMBLE OVERDRIVE SPECIAL

A revised model based on detailed analysis of a very rare Dumble Overdrive Special as used by the likes of Larry Carlton and Robben Ford

  • This sim is based on a real Dumble amp. The SPEC OD sims are based on schematics
  • Cabinet suggestion: 2x12 Custom
  • Original controls: Level and Master, Bass/Middle/Treble, Bright switch, no Presence
  • Wikipedia
WRECKER 1 = TRAINWRECK EXPRESS

Based on the Trainwreck Express—a high quality handmade amp designed and built by Ken Fischer

  • Cabinet suggestion: 4x12 20w or 25w (greenbacks). Red Wirez greenbacks, Ownhammer greenbacks
  • Original controls: Volume (no Master), Bas/Middle/Treble, Presence, Bright switch (off by default).
  • Crank the Master Volume, use Drive for volume and gain. Keep bass low (and/or turn up Low Cut) to prevent flubby bass
  • Don't use this without poweramp simulation, it'll sound terrible. Cliff: "The Trainwreck depends on power amp distortion. The OT has a high impedance which causes the power tubes to enter clipping early. I would not recommend using that model as preamp."
  • FAQ
  • Sound clips
BRIT JM45 = MARSHALL JTM45

Based on a vintage Marshall JTM45 blues amplifier. This amp made famous by Clapton and others was actually a modified version of the original Bassman

  • This amp is based on the Fender Bassman and was the first Marshall amp, 45 watts and 4 Celestion 12" speakers
  • Cabinet suggestion: 4x12 20w or 25w, 4x12 Green. Alternative: Red Wirez Marshall, Ownhammer greenbacks
  • Original controls: Volume, Bass, Middle, Treble
  • Turn down bass (or turn up Low Cut)
  • Wikipedia
  • MarshallForum
DAS METALL = DIEZEL VH4

Based on a high-gain, boutique amplifier head famous for its powerful, heavy and aggressive sound

PLEXI 2 = MARSHALL SUPER LEAD (MODEL 1959)

Similar to Plexi 1 but with a different "bright cap" value and transformer model. Lower gain and more "vintage" sounding

  • Cabinet suggestion: greenbacks (4x12 20w or 25w, 4x12 Green) or G12H30 (4x12 30w). Alternative: Red Wirez Marshall, Ownhammer H75 or M75
  • Original controls: Volume, Bass, Middle, Treble. Presence on later models. Bright (Lead channel)
  • Crank the Master Volume and turn up Drive. Keep Bass low (or turn up Low Cut). Experiment with higher Sag settings
  • Because the bright cap (Lead channel) is very large, the Bright switch in the sim has a great impact on the amount of gain
  • Wiki: Bright switch
  • Wikipedia
  • MarshallForum
SV BASS = AMPEG SVT

Based on the Ampeg SVT (“Super Valve Technology”) that is used for decades by famous bassists the world over

  • Cabinet suggestion: 4x10 Alum, 8x10 Bass, 1x15 Bass. Alternative: Red Wirez SVT
  • Original controls: ...
  • Wikipedia
CA3+ RHY

CA3+ LD

= CUSTOM AUDIO ELECTRONICS 3+ SE: RHYTHM CHANNEL 2 / LEAD CHANNEL 3

CA3+ RHY: Based on channel 2 (Rhythm) of the 3+ SE preamp by CAE. For Ch. 1 (Clean), use the "DOUBLE VERB" model)

CA3+ LD: Based on channel 3 (Lead) of the 3+ SE preamp by CAE designed by Bob Bradshaw

  • Cliff: "Channel 1 isn't modeled because it's very similar to a Fender Twin (Double Verb model)"
  • Cabinet suggestion: n/a
  • Original controls: Gain, Bass, Middle, Treble, Volume, Punch, Presence. Bright switch
  • Original manual
Eggie R20 = EGNATER REBEL 20

Based on the Egnater Rebel 20 20W amplifier head, offering perfect proof that good things really DO come in small packages, (or in this case, DSP packages)

  • Cabinet suggestion: something that sounds like a Celestion Elite 80
  • Original controls: Volume, Bass, Mid, Treble, Master. Tight and Bright switches
  • Cliff: "It's just a Blues Jr. with no negative feedback"
  • Product page, manual etc.
  • Forum
  • Wikipedia
USA IIC+ 1

USA IIC+ 2

= MESA BOOGIE MARK II LEAD: PULL BRIGHT OFF / ON

USA IIC+ 1: Based on a US-made amp famous for its smooth overdrive sound. This model has the pull bright OFF

USA IIC+ 2: Based on a US-made amp famous for its smooth overdrive sound. This model has the pull bright ON

  • Cabinet suggestion: 4x12 Cali. Alternative: Red Wirez Mesa, Ownhammer Mesa
  • Original controls: Volume, Bass, Mid, treble, Bright, Treble Shift, Gain Boost, Pull Bright
  • Wikipedia
  • Original manual
  • Tips in the Wiki
FRYETTE D60L

FRYETTE D60M

= VHT DELIVERANCE 60: LESS / MORE

FRYETTE D60L: Based on the Fryette Amplification D60 in the "Less" mode

FRYETTE D60M: Based on the Fryette Amplification D60 in the "More" mode

  • Cabinet suggestion: one that comes close to a 2x12 or 4x12 cabinet with Eminence 50w speakers
  • Original controls: Gain, Volume, Bass, Middle, Treble, Presence, Depth
  • Original manual
  • Wikipedia
  • User forum
MR. Z 38 SR = DR. Z MAZ 38 Senior

Based on the Dr. Z Maz 38 SR, an amp popular with country and roots players

EURO UBER = BOGNER UBERSCHALL, HIGH-GAIN CHANNEL

Based on the aggressive " High Gain" channel of a 120W head, this model is reminiscent of an 800, modded for heavier, grinding lows and what some call insane gain

  • Cabinet suggestion: simulate a Bogner Uberkab by using a stereo cab or dual cabs with 4x12 German and 4x12 75w. Alternative: Red Wirez Bogner Uberkab
  • Original controls: Gain and Master, Bass/Middle/Treble, Presence, no Bright
  • Keep the Master volume low (3.50). Turn up Presence, add Mids
  • Reworked in firmware 10.x
  • Bogner manual: "One of the most unique items is our "Presence" control. It's an amazing combination of a midrange-presence control. As you sweep through its range you will notice an incredible variety of tones this one control allows. For an extremely aggressive sub-harmonic bass and scooped-midrange sound, keep the presence off or very low. A huge 3-dimensional tone can be found by running the presence around 2 o'clock. Pushing the "Presence" control to maximum will allow you to cut a sonic path through the mix by reinforcing your midrange and slightly rolling off the sub-bass. Trust us: REALLY check out the presence control to unleash the hidden secrets of the UBERSCHALL. The "Midrange" control is very interactive with all the other tone controls, you can go from a hollow scooped-mid setting to an aggressive in your face and on your throat kind of intensity. The "Bass" control allows almost a sub-harmonic low-end to be added, at high volumes be sure to keep the bass down a bit to keep your tone focused like a laser beam"
  • Bogner Twinjet model manual: "The TWIN JET features the original high gain channel with the exception that the presence control which works in the power amp circuit on the regular Uberschall is now in the pre amp circuit which gives you an additional control to shape the sound. Reason is, the TWIN JET has a global master depth and presence control. These affect both channels and will give you control over the overall bass response and presence. Start at 10 to 11 o'clock on the presence and adjust careful to your taste. The depth control is great to give a fuller sound at lower volumes, for higher volumes it will add massive bass and might cover up the rest of the frequencies, best to keep it low but adjust to your taste."
  • Sound clips
  • Original manual and recommended settings
  • Bogner Amp Forum
  • Wikipedia
PVH 5105 = PEAVEY 5150, LEAD CHANNEL, HI-INPUT

Based on the high input lead channel of a high gain amp with the same name as an album so called for the California police code for "criminally insane"

  • This model is probably based on a first generation 5150 (block letters)
  • Cabinet suggestion: 4x12 South. Alternative: Red Wirez Sheffield
  • Original controls: ...
  • Cliff: "The hi-input on the Lead channel is modelled. It has lots of gain. Even at noon it's already very saturated"
  • Keep the Master volume low (3.50)
  • Wikipedia
  • Original manual
Solo X99 Clean

Solo X99 Rhythm Solo X99 Lead

= SOLDANO X99 PREAMP: CLEAN / RHYTHM / LEAD

Based on the Clean / Rhythm / Lead Channel of a very highly regarded rack mount preamplifier

Corncob R100 = CORNFORD RK100

Based on a boutique British amplifier, the Cornford RK100, which is said to have a Plexi-Meets-Modern tone and feel with both subtlety and big cojones

  • Original amp: single channel 100w head, with switchable "hot" control
  • Cabinet suggestion: V30
  • Original controls: Presence, Bass, Middle, Treble, Gain, Volume
  • Turn down Bass and/or Depth to reduce boominess
  • Original manual
  • Videos
  • Audio
  • User forum
CAROLANN OD2 = CAROLANN OD-2R, OVERDRIVE CHANNEL

Based on the celebrated OD2r from CarolAnn Amplifiers as designed by the highly respected Alan Phillips. Alan fine-tuned the Axe-Fx version himself!

  • Introduced in 9.01, improved in 9.03 (collaberation with the designer of Carol-Ann amps)
  • Cabinet suggestion: EV-12 of something that sounds like a Celestion Lead 80. Alternative: Red Wirez EVM, Ownhammer EVM
  • Quote Alan Phillips: "In the real world the OD2 is very very fussy on speaker choice too. The real world speakers of choice are EVM12L in a 1x12 rear ported and 2x12 with Celestion Classic Lead 80's. I found the 12L emulation did a pretty good job. Some of the others sounded so artificial with that model. Like a rockman. Coupled with the right cab the emulated model does a good job of representing the basic tonal signature of the amp". And: "It's not a competitive model, it's a live demo of an OD2 as tweaked by me. Damn sight better than sound clips for auditioning to guys that haven't got the ability to get to a Dealer. Clearly it doesn't give you the full experience of the full amp, but is a good tonal taster. I repaired a Soldano SLO for him one day and when he came over my house to pick it up we just decided it would be a good idea to put a CA model in there. Having the actual builder involved kind of closes the loop fully. I'm happy to endorse that model because I put a lot of hours testing it and putting together a ton of technical information, fourier analysis graphs, frequency response graphs, schematics etc that would make validation of a mathematical model much easier. In reality even though the power amp and the preamp are modelled the pre-amp got the most effort. As I said in another thread, I tuned that by putting the axe in to the actual power amp of an OD2 and running that side by side with a full OD2. The final tweaks were made like that using parametric eq blocks that were hard coded in to the model. You could call that the icing on the cake and basically put the same level of tuning in to the model as I do with a actual OD2. The only difference was I was using a GUI, not resistors and capacitors."
  • Original controls (overdrive channel): Master, Gain, Bass, Middle, Treble, Presence, Bright switch
  • Audio clips
  • User forum
  • Forum
CITRUS RV50 = ORANGE ROCKERVERB 50, DIRTY CHANNEL

We find that this model, based on the "dirty" channel of the 50W head offers all the warmth, tonal quality and rich harmonics generated by the valve-based original

SHIVER CLN

SHIVA LD

= BOGNER SHIVA: CLEAN CHANNEL / LEAD CHANNEL

SHIVA CLN: Based on the 90 watt anniversary model of this versatile amp, this model does powerful shimmering cleans

SHIVA LD: Based on the lead channel of this amp -- sweet rich sounding with an aggressive English style midrange punch

  • Introduced in 10.00
  • Original controls for Clean channel: Bass/Treble, Volume and Master, Bright switch (less to none effective the higher Drive is set)
  • Original controls for Lead channel: Gain and Master, Bass/Middle/Treble, Presence, Bright switch (less effective the higher Drive is set but still noticeable, off by default)
  • The Boost, Mode and Shift controls on the real amp are not modeled
  • Cabinet suggestion: 4x12 German or V30. Alternative: Red Wirez Bogner, Ownhammer V30
  • If the Shiva Ld sim sounds harsh, try turning up the Master Volume
  • Shiva Ld is quite dark, turn up Presence
  • Sound clips
  • Information
  • Original manual
  • Bogner Amp Forum
1987X MOD = MARSHALL 1987X PLEXI, MODDED (BRIGHT CAP REMOVED)

This model based on the 1987X Plexi features what many consider to be an "essential" mod to the amp's tonestack

  • Original amp: 50w reissue of the 60's Marshall 1959SLP. Part of the Vintage Series
  • Introduced in 10.00
  • Original controls: Bass, Mid, Treble, Presence, Volume
  • Cabinet suggestion: greenbacks (4x12 20w or 25w, 4x12 Green) or G12H30 (4x12 30w). Alternative: Red Wirez Marshall, Ownhammer H75 or M75
  • Cliff: "The 1987X MOD model is based on a 1987X Plexi Reissue with C5 removed (which is the most common mod done to this amp)"
  • Crank the Master volume, use Drive for volume and gain, turn down Bass (or turn up Low Cut), turn up Mid and Treble
  • Thread with suggested settings
  • Original manual
  • Wikipedia
  • MarshallForum
MARSHA BE BE

MARSHA HBE HBE

= MARSHA / FRIEDMAN by Rack Systems: BROWN EYE / HAIRY BROWN EYE

MARSHA BE: The Rack Systems Marsha is a new amp by renowned rig builder/amp modder/designer Dave Friedman. This guy knows tone! Here is the amp's Brown Eye channel

MARSHA HBE: The Marsha's Hairy Brown Eye channel is chock full of even more attitude with some pretty wicked gain on tap

  • Original amp: EL34-based modded Marshall Plexi-style tube amp. Single channel, two voicings
  • Introduced in 10.00
  • The name of the real amp name has been changed from Marsha to Friedman
  • Original controls: Gain and Master, Bass/Middle/Treble, Presence, no Bright
  • Keep the Master low (3.50), experiment with Bright or turn up Presence
  • Cabinet suggestion: greenbacks (4x12 Green, 4x12 20w or 25w), G12H30 (4x12 30w) or something with V30s. Alternative: Red Wire Marshall, Ownhammer H75 or M75
  • Forum
  • Amp information
  • YouTube clip with sample settings