Always consult the official Owners Manuals first!
March 2024: all pages have been checked and are up-to-date
Difference between revisions of "Spillover"
(106 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
− | + | __TOC__ | |
+ | =About spillover= | ||
− | + | Spillover refers to the functionality to keeping the trails of the delay and/or reverb audible after switching the effect off or switching presets, scenes, channels or X/Y. | |
− | |||
− | |||
− | |||
− | + | All FAS processors support spillover under certain conditions as explained in the [[Owners_Manuals|manuals]]. | |
− | |||
− | |||
− | |||
− | =Spillover | + | =Spillover between presets= |
− | |||
− | + | Spillover between presets is enabled or disabled in the Global menu. It requires additional steps to make it work, as explained in the [[Owners_Manuals|manuals]]. The setting in the Global menu applies to switching between presets only. Not to switching scenes, channels or X/Y, or bypassing blocks. | |
− | |||
− | [[category: | + | <blockquote>"Global spillover settings only apply to preset changes. Spillover between scenes is, in general, desirable and controlled by the bypass mode and state of the various blocks." [http://forum.fractalaudio.com/threads/scene-switching-with-spillover-noise.146144/#post-1728091 source]</blockquote> |
+ | |||
+ | Turn off Spillover in the Global menu if you prefer “silent” switching between presets. | ||
+ | |||
+ | Forum member: "I have two patches that both has delay blocks disabled and when I switch between these patches the delay spillover sometimes kicks in really loud." | ||
+ | |||
+ | <blockquote>"This can happen if you rapidly switch between presets many times. The unit requires a small amount of time between preset changes to clear unused buffer space. This is done as a background task." [http://forum.fractalaudio.com/threads/unpredictable-spillover-kick-in.39269/#post-534665 source] </blockquote> | ||
+ | |||
+ | If you use the Mix and Level parameters to dial in the desired effects level, the volume level of the reverb and/or delay trails may change when switching presets. This can be prevented by keeping Mix and Level at fixed values, and using Input Gain to set the desired effects level. [http://forum.fractalaudio.com/ultra-std-discussion/42536-adding-parallel-rows-grid-increases-volume.html#post565766 source] | ||
+ | |||
+ | The [[Multi Delay block]], [[Ten-Tap Delay block]], [[Plex Delay block]] and [[Megatap block]] don’t support spillover between presets. | ||
+ | |||
+ | True independent spillover is not supported because it would require double the processing. | ||
+ | |||
+ | =Spillover between scenes, channels or X/Y= | ||
+ | |||
+ | The Global Spillover setting doesn't apply to spillover when turning off effects or switching scenes, channels or X/Y. Delay and Reverb trails always ring out when switching scenes, depending on the effect block's [[Presets#Bypass_mode_of_an_effect_block|Bypass Mode]] setting, see below. This is inherent to the way scenes work. When it comes to spillover, scenes work better than presets and are easier to set up. | ||
+ | |||
+ | <blockquote>"Spillover is in there but the "right" way to do it is to use scenes. If you stay within a preset and use channels and scenes the spillover is perfect." [http://forum.fractalaudio.com/threads/spill-over.136766/#post-1620530 source] </blockquote> | ||
+ | |||
+ | Spillover can be affected when switching between the X/Y states or Channels of an effect, if drastically different algorithms exist between the two states. For example, if one scene has a Digital Delay and the next scene uses a Tape Delay, spillover will probably not function correctly as these modes use different algorithms. | ||
+ | |||
+ | [[Scene controllers]] allow more control over what happens with the sound when changing scenes. | ||
+ | |||
+ | =Spillover when bypassing effects= | ||
+ | |||
+ | The [[Presets#Bypass_mode_of_an_effect_block|Bypass Mode]] of an effect block determines if the reverb or delay trails ring out after turning off the effect, or are muted. | ||
+ | |||
+ | =More information= | ||
+ | |||
+ | [https://forum.fractalaudio.com/threads/wicked-wiki-1-optimizing-spillover.49144/ Wicked Wiki article] | ||
+ | |||
+ | [https://www.youtube.com/watch?v=iGAj6i9zHbI Leo’s Todd’s Basics tutorial] | ||
+ | |||
+ | [[category:Axe-Fx2]] | ||
+ | [[category:Axe-Fx3]] | ||
+ | [[category:FM3]] | ||
+ | [[category:FX8]] | ||
+ | [[category:AX8]] | ||
+ | [[category:Sounds]] |
Revision as of 09:42, 2 August 2019
Contents
About spillover
Spillover refers to the functionality to keeping the trails of the delay and/or reverb audible after switching the effect off or switching presets, scenes, channels or X/Y.
All FAS processors support spillover under certain conditions as explained in the manuals.
Spillover between presets
Spillover between presets is enabled or disabled in the Global menu. It requires additional steps to make it work, as explained in the manuals. The setting in the Global menu applies to switching between presets only. Not to switching scenes, channels or X/Y, or bypassing blocks.
"Global spillover settings only apply to preset changes. Spillover between scenes is, in general, desirable and controlled by the bypass mode and state of the various blocks." source
Turn off Spillover in the Global menu if you prefer “silent” switching between presets.
Forum member: "I have two patches that both has delay blocks disabled and when I switch between these patches the delay spillover sometimes kicks in really loud."
"This can happen if you rapidly switch between presets many times. The unit requires a small amount of time between preset changes to clear unused buffer space. This is done as a background task." source
If you use the Mix and Level parameters to dial in the desired effects level, the volume level of the reverb and/or delay trails may change when switching presets. This can be prevented by keeping Mix and Level at fixed values, and using Input Gain to set the desired effects level. source
The Multi Delay block, Ten-Tap Delay block, Plex Delay block and Megatap block don’t support spillover between presets.
True independent spillover is not supported because it would require double the processing.
Spillover between scenes, channels or X/Y
The Global Spillover setting doesn't apply to spillover when turning off effects or switching scenes, channels or X/Y. Delay and Reverb trails always ring out when switching scenes, depending on the effect block's Bypass Mode setting, see below. This is inherent to the way scenes work. When it comes to spillover, scenes work better than presets and are easier to set up.
"Spillover is in there but the "right" way to do it is to use scenes. If you stay within a preset and use channels and scenes the spillover is perfect." source
Spillover can be affected when switching between the X/Y states or Channels of an effect, if drastically different algorithms exist between the two states. For example, if one scene has a Digital Delay and the next scene uses a Tape Delay, spillover will probably not function correctly as these modes use different algorithms.
Scene controllers allow more control over what happens with the sound when changing scenes.
Spillover when bypassing effects
The Bypass Mode of an effect block determines if the reverb or delay trails ring out after turning off the effect, or are muted.