Always consult the Owners Manuals and FAQs first.
FM3 information is being added as it becomes available, but it's preliminary and not final until release

Difference between revisions of "Phaser block"

From Axe-Fx II Wiki
Jump to: navigation, search
(Mono or stereo)
(Script and Block)
 
(46 intermediate revisions by the same user not shown)
Line 3: Line 3:
 
[[image:Phaser block.png|350px]]
 
[[image:Phaser block.png|350px]]
  
=Available on which Fractal Audio products=
+
=Available on which products=
  
 
* '''Axe-Fx III''': 2 blocks
 
* '''Axe-Fx III''': 2 blocks
 +
* '''FM3''': yes @@
 
* '''Axe-Fx II''': 2 blocks
 
* '''Axe-Fx II''': 2 blocks
 
* '''AX8''': 1 block
 
* '''AX8''': 1 block
 
* '''FX8''': 2 blocks
 
* '''FX8''': 2 blocks
  
=X/Y and channels=
+
=Channels or X/Y switching=
  
* '''Axe-Fx III''': 4 channels
+
* '''Axe-Fx III''' and '''FM3''': 4 channels
 
* '''Axe-Fx II''': X/Y
 
* '''Axe-Fx II''': X/Y
 
* '''AX8''': X/Y
 
* '''AX8''': X/Y
 
* '''FX8''': X/Y
 
* '''FX8''': X/Y
  
=Uni-Vibe=
+
=Phaser types and effects=
 +
 
 +
==Script and Block==
 +
 
 +
These types are based on the MXR Phase 90 and Phase 45, Script and Block versions.
 +
 
 +
The "Phase 45" type uses subtle two-stage phasing, while the "Phase 90" type uses more pronounced four-stage phasing.
 +
 
 +
The "Script" type has a more subdued sound with higher headroom and greater clarity. The "Block" type is more modern and relies on internal feedback to create light harmonic distortion and give the effect a more accentuated swoosh.
 +
 
 +
Forum member Guitarnerdswe created even closer digital replicas of the MXR Phase 90 (script and block) by attaching an LFO to the Start Frequency parameter. [https://forum.fractalaudio.com/threads/i-matched-a-mxr-phase-90.153314/ Read more]
 +
 
 +
==Uni-Vibe==
  
 
The Uni-Vibe effect is available as a special mode of the Phaser block. Engage the Vibe mode (or select the Classic Vibe type).
 
The Uni-Vibe effect is available as a special mode of the Phaser block. Engage the Vibe mode (or select the Classic Vibe type).
Line 24: Line 37:
  
 
More settings:
 
More settings:
* [http://forum.fractalaudio.com/axe-fx-ii-preset-exchange/83367-still-looking-perfect-fat-robin-trower-univibe-sound-3.html Robin Trower]
+
* [https://forum.fractalaudio.com/threads/still-looking-for-that-perfect-fat-robin-trower-univibe-sound.83367/ Robin Trower]
 
* [http://forum.fractalaudio.com/threads/vibe.138468/#post-1641918 Shin-ei Vibe-Bro]
 
* [http://forum.fractalaudio.com/threads/vibe.138468/#post-1641918 Shin-ei Vibe-Bro]
  
Line 35: Line 48:
 
More information:
 
More information:
  
* [http://en.wikipedia.org/wiki/Univibe Uni-Vibe in Wikipedia]
+
* [http://en.wikipedia.org/wiki/Univibe Wikipedia]
 
* [http://www.gilmourish.com/?page_id=4537 Gilmourish.com]
 
* [http://www.gilmourish.com/?page_id=4537 Gilmourish.com]
  
=Barber Pole Phaser=
+
==Barber Pole==
 +
 
 +
Like the "Shepard tone", this type creates the illusion of a never-ending upwards cycle. Works best when placed at the end of the chain.
 +
 
 +
==Bi-Phase==
 +
 
 +
Set the Phaser to 6 stages to emulate a Mutron Bi-Phase.
 +
 
 +
<blockquote>"For the double-phaser of the original, set it to 12-stage with LFO Phase at 0." [http://forum.fractalaudio.com/threads/stereo-8-stage-phaser-holy-crap.142326/#post-1685205 source]</blockquote>
  
Like the "Shepard" tone, this creates the illusion of a never-ending upwards cycle. Works best when placed at the end of the chain.
+
==Step Phaser==
  
=Mono or stereo output=
+
To simulate a stepped phaser, set Depth to 0, attach Frequency Start to the Sequencer, set Min and Max and adjust the Sequencer faders.
  
Phaser defaults to mono to prevent phase problems when used before an Amp block. To make it stereo, change the LFO Phase setting and place it after Drive, Amp and Cab.
+
=Mono or stereo Phaser=
 +
 
 +
Phaser defaults to mono to prevent phase problems when used before an Amp block.
 +
 
 +
To make it stereo, change the LFO Phase setting and place it after Drive, Amp and Cab.
 +
 
 +
=Thump when engaging the Phaser=
 +
 
 +
Engaging some effects, like Wah or Phaser, can cause a "thump" in the sound. This may be caused by impedance switching. To solve this, change Input Impedance from "Auto" to "1M". The above doesn't apply to Fractal Audio processors with a fixed (not adjustable) input impedance. Read this: [[Input impedance]]
  
 
=Parameters=
 
=Parameters=
Line 53: Line 82:
 
|-
 
|-
 
! '''Parameter'''
 
! '''Parameter'''
! '''Axe-Fx III'''
+
! '''Axe-Fx III / FM3'''
 
! '''Axe-Fx II'''
 
! '''Axe-Fx II'''
! '''AX8, FX8'''
+
! '''AX8 / FX8'''
 
|-
 
|-
 
| Type
 
| Type
Line 82: Line 111:
 
!  
 
!  
 
|-
 
|-
| Frequency
+
| Start Frequency
 
! yes
 
! yes
 
!  
 
!  
Line 128: Line 157:
 
|-
 
|-
 
| LFO Reset on Bypass
 
| LFO Reset on Bypass
 +
! yes
 +
!
 +
!
 +
|-
 +
| Barberpole — Sweep Direction
 +
! yes
 +
!
 +
!
 +
|-
 +
| Barberpole — Filter Q
 
! yes
 
! yes
 
!  
 
!  
Line 135: Line 174:
 
==Level==
 
==Level==
  
<blockquote>"Phasers cause notches in the spectrum which can reduce the apparent volume. It depends on the frequency content. Overdriven sounds have more content and will be affected more. The Level knob allows you to compensate for this."</blockquote>
+
<blockquote>"Phasers cause notches in the spectrum which can reduce the apparent volume. It depends on the frequency content. Overdriven sounds have more content and will be affected more. The Level knob allows you to compensate for this." [https://forum.fractalaudio.com/threads/phaser-level-too-low.139671/post-1656156 source] </blockquote>
  
 
==Order==
 
==Order==
Line 147: Line 186:
 
==LFO Bypass Reset==
 
==LFO Bypass Reset==
  
If LFO Bypass Reset is set to anything other than Off, the LFO will be reset to the selected phase whenever the block is bypassed. This allows synchronizing the sweep to the engagement of the effect.
+
If LFO Bypass Reset is set to anything other than Off, LFO will be reset to the selected phase whenever the block is bypassed. This allows synchronizing the sweep to the engagement of the effect.
 
 
=Troubleshooting=
 
  
==Thump when engaging the Phaser==
+
==Start Frequency==
  
If engaging/bypassing the Phaser block causes an audible thump or gap, change input impedance to 1M (Axe-Fx II, III and FX8).
+
<blockquote>"Another fun phaser trick is to set DEPTH to 0 and assign the Frequency Start to an expression pedal." [http://forum.fractalaudio.com/threads/stereo-8-stage-phaser-holy-crap.142326/#post-1685205 source]</blockquote>
  
 
[[category:Axe-Fx2]]
 
[[category:Axe-Fx2]]
 
[[category:Axe-Fx3]]
 
[[category:Axe-Fx3]]
 +
[[category:FM3]]
 
[[category:FX8]]
 
[[category:FX8]]
 
[[category:AX8]]
 
[[category:AX8]]
 
[[category:Sounds]]
 
[[category:Sounds]]

Latest revision as of 13:15, 16 October 2019

Phaser block.png

Available on which products

  • Axe-Fx III: 2 blocks
  • FM3: yes @@
  • Axe-Fx II: 2 blocks
  • AX8: 1 block
  • FX8: 2 blocks

Channels or X/Y switching

  • Axe-Fx III and FM3: 4 channels
  • Axe-Fx II: X/Y
  • AX8: X/Y
  • FX8: X/Y

Phaser types and effects

Script and Block

These types are based on the MXR Phase 90 and Phase 45, Script and Block versions.

The "Phase 45" type uses subtle two-stage phasing, while the "Phase 90" type uses more pronounced four-stage phasing.

The "Script" type has a more subdued sound with higher headroom and greater clarity. The "Block" type is more modern and relies on internal feedback to create light harmonic distortion and give the effect a more accentuated swoosh.

Forum member Guitarnerdswe created even closer digital replicas of the MXR Phase 90 (script and block) by attaching an LFO to the Start Frequency parameter. Read more

Uni-Vibe

The Uni-Vibe effect is available as a special mode of the Phaser block. Engage the Vibe mode (or select the Classic Vibe type).

The default settings are modeled after the Fulltone Deja-Vibe. source

More settings:

Put the effect before the Amp block.

"You need it before the amp if you want the bump." source

Connect a pedal or switch to the Rate parameter to control speed.

More information:

Barber Pole

Like the "Shepard tone", this type creates the illusion of a never-ending upwards cycle. Works best when placed at the end of the chain.

Bi-Phase

Set the Phaser to 6 stages to emulate a Mutron Bi-Phase.

"For the double-phaser of the original, set it to 12-stage with LFO Phase at 0." source

Step Phaser

To simulate a stepped phaser, set Depth to 0, attach Frequency Start to the Sequencer, set Min and Max and adjust the Sequencer faders.

Mono or stereo Phaser

Phaser defaults to mono to prevent phase problems when used before an Amp block.

To make it stereo, change the LFO Phase setting and place it after Drive, Amp and Cab.

Thump when engaging the Phaser

Engaging some effects, like Wah or Phaser, can cause a "thump" in the sound. This may be caused by impedance switching. To solve this, change Input Impedance from "Auto" to "1M". The above doesn't apply to Fractal Audio processors with a fixed (not adjustable) input impedance. Read this: Input impedance

Parameters

Parameters table

Parameter Axe-Fx III / FM3 Axe-Fx II AX8 / FX8
Type yes
Rate yes
Tempo yes
Depth yes
Feedback yes
Start Frequency yes
Phaser Mode yes
Order yes
Frequency Span yes
LFO Type yes
LFO Phase yes
Bulb Bias yes
Feedback Tap yes
Tone yes
LFO Reset on Bypass yes
Barberpole — Sweep Direction yes
Barberpole — Filter Q yes

Level

"Phasers cause notches in the spectrum which can reduce the apparent volume. It depends on the frequency content. Overdriven sounds have more content and will be affected more. The Level knob allows you to compensate for this." source

Order

Increase the Order parameter to simulate phasers such as the EHX Small stone and Mu-tron Bi-Phase.

Feedback Tap

"There is no feedback on a Script 90." source

LFO Bypass Reset

If LFO Bypass Reset is set to anything other than Off, LFO will be reset to the selected phase whenever the block is bypassed. This allows synchronizing the sweep to the engagement of the effect.

Start Frequency

"Another fun phaser trick is to set DEPTH to 0 and assign the Frequency Start to an expression pedal." source