Search results

Create the page "Connecting to a power amp and speaker cabinet" on this wiki! See also the search results found.

• X-Load LB-2 Reactive Load Box
  ...'s speaker jack, to be amplified further down the chain or to be used with cabinet modeling. ...een mentioned by Fractal Audio in the past, but it was never been released and perhaps has never been created.
  16 KB (2,470 words) - 12:36, 8 April 2024
• Tone Match block
  =Tone matching and amp matching= ...<q>Live</q> is used to describe the process of matching the tone of a real amp.
  21 KB (3,490 words) - 17:23, 8 April 2024
• Setup menu
  The Setup menu on the Axe-Fx III, FM9 and FM3 gives access to important system parameters. It has the following submenus. ...ed FC-6 and FC-12 controllers. Read [[FC-6_and_FC-12_foot_controllers|FC-6 and FC-12 foot controllers]] for more information.
  18 KB (2,979 words) - 16:07, 16 April 2024
• FX8
  <font color=red>The FX8 (amp modeler and multi-effects pedalboard) has been discontinued. This page will not be upda ...for amp channel switching and other amp functions. It does not provide amp and cab modeling.
  33 KB (5,417 words) - 00:24, 3 January 2024
• Firmware release notes - FM9
  ...lled, please see this article: [https://support.fractalaudio.com/en-US/how-to-resolve-dyna-cabs-not-installed-or-incorrect-version-286538] ...values already saved (see below), controller LFOs updated in a few cases, and CPUlevel reduced on “Poltergeist Pig”. [https://www.fractalaudio.com/fm
  50 KB (7,888 words) - 18:24, 15 April 2024
• Amp modeling techniques
  =About Fractal Audio's amp modeling= ...modeling, starting with the Axe-Fx II, based on the firmware release notes and quotes.
  89 KB (14,071 words) - 21:42, 24 April 2024
• Firmware release notes - FM3
  ...improved in general even with this setting turned off. For preset changes to use the new gapless switching, two conditions must be met: * Setup > Global Settings > Config > Spillover must be set to “ALL”
  56 KB (8,824 words) - 14:24, 30 April 2024
• I/O connectivity and levels
  ...ne level : The lowest output level (often -60 dbV), as used in microphones and on microphone inputs on mixers. ; Instrument level : The output level of guitars, basses etc., and effects pedals.
  155 KB (25,257 words) - 16:49, 16 April 2024
• Axe-Fx III, FM9 and FM3
  ...n Family]</q> is a good starting point. Also <q>[[Comparing the Axe-Fx III to the Axe-Fx II]]</q> is useful for its comparison of the two units. ...um.fractalaudio.com/threads/ooooh-charts-and-graphs.135900 Ooooh... Charts and Graphs]</q>.
  75 KB (11,235 words) - 23:18, 20 April 2024
• Firmware release notes - Axe-Fx III
  Added “1x12 Friedman” speaker impedance curve. Fixed clicks and pops can occur when adjusting drive level of Rat Distortion.
  134 KB (21,574 words) - 17:34, 2 May 2024
• Firmware release notes - Axe-Fx II
  * This firmware incorporates some of the amp modeling improvements from the latest Axe-Fx III firmware. ...nded to do a “soft reset” of the Amp block on these presets by deselecting and then reselecting the model.
  194 KB (31,845 words) - 17:59, 14 February 2024
• Amp block
  * '''FX8''': n/a =Amplifier and cabinet modeling for beginners=
  431 KB (68,296 words) - 14:58, 20 April 2024
• Factory presets
  ..., B and C). The presets demonstrate amp tones (Bank A) and effects (Bank B and C). ...lly and makes them available on the [https://www.fractalaudio.com website] and the [https://forum.fractalaudio.com/whats-new/posts/6512952/ user forum]. [
  97 KB (15,554 words) - 23:30, 21 April 2024