Search results

Create the page "Compressor/Dynamics effect" on this wiki! See also the search results found.

• Effects list
  The table below displays the available effect blocks per product. | Compressor/Dynamics (4)
  4 KB (503 words) - 14:50, 5 February 2024
• X/Y switching
  Most effect blocks in the Axe-Fx II, FX8 and AX8 can be switched quickly between two se =Which effect blocks support X/Y=
  6 KB (1,005 words) - 12:18, 8 April 2024
• Compressor block
  =Compressor block diagram= [[image:Compressor block.PNG|300px]]
  27 KB (4,024 words) - 18:16, 16 April 2024
• Firmware release notes - AX8
  ...phasis. These parameters can be used to tailor the response of the various compressor types to different material. AX8 V7.02 adds MOTOR DRIVE to the AMP block, as well as some effect block enhancements.
  46 KB (7,455 words) - 11:00, 15 January 2024
• Firmware release notes - FM9
  .... Typical plates are around 25-50%. Set to higher values to exaggerate the effect. Stereo imaging is adjustable via the “Pickup Spacing” parameter. * AMP effect now has 32 less sample times of latency.
  50 KB (7,888 words) - 18:24, 15 April 2024
• Amp modeling techniques
  ...curve resulting in a clearer low end. New algorithm now also accounts for effect of speaker impedance on transformer response. Improved power tube modeling. This yields better dynamics, improved low frequency accuracy and more accurate interaction with output
  89 KB (14,071 words) - 21:42, 24 April 2024
• Zery uninteresting wiki sandbox
  The direct signal has more lows and highs too because of the proximity effect (distance between mic and speaker). Also, the directivity of studio monitor == Why does the volume decrease or increase when I bypass an effect in a parallel row? ==
  30 KB (5,012 words) - 20:10, 7 April 2024
• Firmware release notes - FM3
  * Fixed audio drop from the Compressor block when Ratio is set to 1.0. ...d new Optical Sustainer, Analog Sustainer, and JFET Sustainer types to the Compressor block.
  48 KB (7,631 words) - 16:33, 15 April 2024
• Presets
  * Re-use effect blocks with preferred settings and levels, through [[Global blocks]] or the ...ects in front of Amp and Drive blocks should not be set to stereo. Certain effect blocks, such as Amp, Drive and mono Cab, sum the signal to monoaural. Check
  64 KB (10,468 words) - 23:06, 18 April 2024
• Firmware release notes - Axe-Fx III
  .... Typical plates are around 25-50%. Set to higher values to exaggerate the effect. Stereo imaging is adjustable via the Pickup Spacing parameter. Improved Compressor block:
  134 KB (21,544 words) - 17:43, 19 April 2024
• MIDI SysEx
  ...ect-bypass-status-info-available.html SysEx commands for retrieving Preset/Effect bypass states] ...ormation about each effect block in preset follows, using 5 bytes for each effect block in the preset
  114 KB (16,586 words) - 23:11, 24 December 2023
• Firmware release notes - Axe-Fx II
  ...phasis. These parameters can be used to tailor the response of the various compressor types to different material. * Improved Amp block output compressor. New algorithm is more musical and reacts faster to transients. If you are
  194 KB (31,845 words) - 17:59, 14 February 2024
• Amp block
  ...e removed to allow the algorithms to run including the bias tremolo, input dynamics processing […] * Recall Effect (if supported by your device) — load the values of an AMP block from one
  431 KB (68,296 words) - 14:58, 20 April 2024
• Amplifier models list
  # "A 5150's presence control has almost no effect from 0 to 7. After 7 the treble increases rapidly. The taper of the presenc ...n doesn't change much as you change the operating point, hence the tremolo effect is subtle. Bias tremolo works best on amps with little to no negative feedb
  282 KB (42,650 words) - 16:03, 19 April 2024