Search results

Create the page "Spillover: reverb and delay" on this wiki! See also the search results found.

• Spillover
  =About spillover= Spillover refers to the ability to keep the trails of the delay or reverb intact after switching the effect off or switching presets, scenes or chann
  4 KB (585 words) - 16:02, 16 April 2024
• Megatap Delay block
  * '''Axe-Fx III''' and '''FM9''': 2 blocks * '''Axe-Fx II''' and '''FX8''': 1 block
  4 KB (508 words) - 14:00, 20 April 2024
• Plex Delay block
  =About the Plex Delay= ...dedicated effect block on the Axe-Fx III, FM9 and FM3. It provides up to 8 delay lines in a feedback arrangement for ethereal “shimmer” effects.
  4 KB (600 words) - 20:06, 2 March 2024
• Multitap Delay block
  =About the Multitap Delay block= ...Multitap Delay block provides many types, partly provided by forum member and effects guru Simeon.
  5 KB (806 words) - 16:50, 16 April 2024
• Channels
  ...er values. Switching between channels is instantaneous and pretty seamless and can be done manually (on the hardware or with a foot controller) or automat ...annel A is a DELUXE VERB model, Channel B is a PLEXI, Channel C is a RECTO and Channel D is FAS MODERN. Then, change channels (sounds) almost instantly at
  7 KB (1,115 words) - 09:09, 6 May 2024
• Reverb block
  * [[FAS-FX Reverb plugin]] =FAS-FX Reverb plugin=
  29 KB (4,411 words) - 16:12, 16 April 2024
• Delay block
  =Delay block diagrams= [[image:Delay block - Mono.PNG|450px]]
  29 KB (4,431 words) - 17:43, 16 April 2024
• Scenes
  The difference between presets, scenes and channels: ...our traditional pedalboard at a particular moment, with effects on or off, and set to specific sounds.
  18 KB (3,060 words) - 09:09, 6 May 2024
• Presets
  * Mark I and II: 384 * XL and XL+: 768
  64 KB (10,563 words) - 09:10, 6 May 2024
• Firmware release notes - FM9
  ...values already saved (see below), controller LFOs updated in a few cases, and CPUlevel reduced on “Poltergeist Pig”. [https://www.fractalaudio.com/fm ...ng them closer to their real world counterparts, with more rumble and bite and other nasty things that tube amps do.
  50 KB (7,888 words) - 18:24, 15 April 2024
• Firmware release notes - FM3
  ...tings > Config > Gapless Changes has three settings: Off, Channel & Scene, and “All” (Preset, Scene, Channel). Note that channel switching speed has b * Setup > Global Settings > Config > Spillover must be set to “ALL”
  56 KB (8,824 words) - 14:24, 30 April 2024
• Axe-Fx III, FM9 and FM3
  ...um.fractalaudio.com/threads/ooooh-charts-and-graphs.135900 Ooooh... Charts and Graphs]</q>. ...hree switches each. An FM3 has one board. An FC6 has two. An FM9 has three and an FC12 has four.
  75 KB (11,235 words) - 23:18, 20 April 2024
• FX8
  <font color=red>The FX8 (amp modeler and multi-effects pedalboard) has been discontinued. This page will not be upda ...for amp channel switching and other amp functions. It does not provide amp and cab modeling.
  33 KB (5,417 words) - 00:24, 3 January 2024
• Firmware release notes - Axe-Fx III
  Fixed clicks and pops can occur when adjusting drive level of Rat Distortion. ...ved optical types in Tremolo block. Additionally, the LFO Type, Duty Cycle and Shape are now set to the most appropriate values when selecting the Tremolo
  134 KB (21,574 words) - 17:34, 2 May 2024
• Firmware release notes - Axe-Fx II
  ...nded to do a “soft reset” of the Amp block on these presets by deselecting and then reselecting the model. * Improved speaker compression modeling and interaction with power amp. This results in a more dynamic response.
  194 KB (31,845 words) - 17:59, 14 February 2024