Search results

Create the page "Effect" on this wiki! See also the search results found.

• Firmware release notes - AX8
  AX8 V7.02 adds MOTOR DRIVE to the AMP block, as well as some effect block enhancements. ...he unit always returns to the main screen. This prevents display issues in effect blocks. It is also consistent with the behavior of the Single Preset Footsw
  46 KB (7,455 words) - 11:00, 15 January 2024
• MIDI
  ...loading presets, enable mapping of Program Changes, and choose between two Effect Bypass modes. The MIDI settings are part of the system data which can be ba ==Effect Bypass Mode==
  43 KB (6,811 words) - 05:58, 1 March 2024
• Firmware release notes - FM3
  * Fixed crash in Synth effect under certain circumstances. ...100%, (e.g. wah, EQ, etc.) The new feature smooths the transition when the effect is turned on or off.
  56 KB (8,824 words) - 14:24, 30 April 2024
• Setup menu
  Boost/Pad is not intended for boosting USB output (although it does have that effect). Usually you will use this when you send the effect loop out before the amp block. The signal will be weak going to the D/A con
  18 KB (2,979 words) - 16:07, 16 April 2024
• MIDI SysEx
  ...ect-bypass-status-info-available.html SysEx commands for retrieving Preset/Effect bypass states] ...ormation about each effect block in preset follows, using 5 bytes for each effect block in the preset
  114 KB (16,586 words) - 23:11, 24 December 2023
• Axe-Fx II
  ...on the Recall screen: copy and paste effect settings with [[Presets|Recall Effect]]. * Assign a switch assigned to the effect's X/Y MIDI CC
  33 KB (5,066 words) - 10:51, 27 February 2024
• Noise gate
  ...the preset is set to “Off”, the global Noisegate Offset value will have no effect. The default value is 0 dB and is set to that upon a system reset.
  14 KB (2,052 words) - 17:09, 5 April 2024
• Cab block
  ...ffects is usually subtle. It depends on how non-linear or time-variant the effect is. For effects like EQ, which are linear and time-invariant, it doesn't ma [http://forum.fractalaudio.com/threads/no-effect-loop-in-axe-fx´s-amp-models.22802/#post-369849]
  86 KB (13,675 words) - 13:30, 26 May 2024
• FC-6 and FC-12 foot controllers
  The FC will sometimes briefly display messages, for example when turning an effect on and off. In the FC configuration you specify the on-display time for the ...s allows Channel switches to serve double duty by engaging or bypassing an effect. To use this option, stomp again on the footswitch for a currently selected
  27 KB (4,240 words) - 16:52, 16 April 2024
• FAMC Liquid Foot+
  | External Dev Sync- AXE-FX3: Change to a specific channel of a specific effect, or Change it's BYPASS STATE *** Under Sync Effect, Select: SCENE 1 and Click Yes, if you get the Auto-Program popup window
  126 KB (20,509 words) - 21:51, 27 May 2024
• Editors
  Click on a effect block to display parameters and controls. ...: When supported by a block, this lets you select a specific type of the effect. This acts as a kind of super parameter, and changing it can cause other pa
  73 KB (11,949 words) - 18:25, 16 May 2024
• Amp modeling techniques
  ...curve resulting in a clearer low end. New algorithm now also accounts for effect of speaker impedance on transformer response. .... Note that the majority of the response is in the subsonic region and the effect is primarily tactile. Existing presets are not affected and the value will
  90 KB (14,099 words) - 16:03, 30 May 2024
• Factory presets
  The presets were dialed in loud so as to be sure the Fletcher-Munson effect did not influence the sound. ...e of a piezo-equipped guitar. An LFO-controlled Pitch block reproduces the effect of a TC Mimiq pedal (double tracking). The FM3 version is simplified. FM3 a
  97 KB (15,554 words) - 23:30, 21 April 2024
• Firmware release notes - Axe-Fx III
  .... Typical plates are around 25-50%. Set to higher values to exaggerate the effect. Stereo imaging is adjustable via the Pickup Spacing parameter. ...curve resulting in a clearer low end. New algorithm now also accounts for effect of speaker impedance on transformer response.
  135 KB (21,674 words) - 16:00, 30 May 2024
• I/O connectivity and levels
  '''A:''' Many SETUP and EFFECT parameters change the gain level. Some of these are intended to change gain * The LEVEL parameter of every effect increases or decreases the overall level.
  155 KB (25,257 words) - 16:49, 16 April 2024
• Digital I/O and computer audio
  ...n tweak the signal on the Axe-Fx II by creating an empty preset and adding effect blocks, such as Amp and Cab. When you are happy with the result, record cha
  26 KB (4,039 words) - 15:08, 6 June 2024
• Firmware release notes - Axe-Fx II
  ...s driven and is more noticeable as the MV is increased. Also note that the effect in real amps is highly dependent on the speaker. Some speaker/transformer c * Change “Thru” bypass mode so that effect input is muted. This prevents, for example, delays from creating echoes whe
  194 KB (31,845 words) - 17:59, 14 February 2024
• Impulse responses (IR)
  This causes two things. The first is a psychoacoustic effect because the sound changes rapidly with angle and our ears are a finite dist ...exacerbates the change in sound vs. angle and the resulting psychoacoustic effect.
  71 KB (11,651 words) - 13:58, 20 April 2024
• Amp block
  * Recall Effect (if supported by your device) — load the values of an AMP block from one ...nsformer orientation, phase of the moon, etc. And while these do have some effect, it is arguably inconsequential relative to the single biggest source of de
  432 KB (68,488 words) - 19:46, 12 June 2024
• Drive block
  ...trap, gear, etc. algorithms. It dampens numerical ringing without the side-effect of damping actual circuit ringing. Once you see how it works it seems hard ...oil of wire that creates a magnetic field. Used in Wah pedals to voice the effect.
  264 KB (42,826 words) - 07:11, 28 May 2024

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)