Search results

Create the page "Effect" on this wiki! See also the search results found.

• AX8
  ...access the global menus, to switch to the previous menu page, to bypass an effect, as an editing shortcut ...ou can also assign other functions, aka "footswitch blocks". You assign an effect or function by selecting a footswitch, turning the VALUE knob and pressing
  26 KB (4,192 words) - 00:35, 3 January 2024
• Firmware release notes - FX8
  ...or is placed before Amp. Use “Line” when compressor is placed in the amp’s effect loop. ...ameters other than the Balance no longer mutes the output on the following effect blocks:
  23 KB (3,724 words) - 00:37, 2 January 2024
• Delay block
  The following blocks are also capable of providing a delay effect: ...ulating the motor speed (which changes the tape speed) is a very different effect than modulating the delay time. You can hear the difference between by vary
  29 KB (4,431 words) - 17:43, 16 April 2024
• Pitch block
  The devices offer several ways to create an Octaver (octave down) effect: ...irl</q> associated with 80's chorus tone. Use it in stereo for a very wide effect. Van Halen's sound on the <q>Balance</q> album is well-known example of ste
  31 KB (4,751 words) - 16:15, 16 April 2024
• Compressor block
  ; JFET Compressor : Field Effect Transistor-based compression, emulating tube compressors. The most famous F Compressors are used mostly as a 100% wet effect. But there are a few compressors with Blend or Mix controls. Use the Mix pa
  27 KB (4,050 words) - 11:32, 21 May 2024
• Zery uninteresting wiki sandbox
  The direct signal has more lows and highs too because of the proximity effect (distance between mic and speaker). Also, the directivity of studio monitor == Why does the volume decrease or increase when I bypass an effect in a parallel row? ==
  30 KB (5,012 words) - 20:10, 7 April 2024
• Presets
  * Re-use effect blocks with preferred settings and levels, through [[Global blocks]] or the ...ects in front of Amp and Drive blocks should not be set to stereo. Certain effect blocks, such as Amp, Drive and mono Cab, sum the signal to monoaural. Check
  64 KB (10,563 words) - 09:10, 6 May 2024
• Speakers and microphones
  ...he KSM313 a little more balanced. The R121 has a lot of bass and proximity effect and the high end can be a little dull.
  9 KB (1,244 words) - 11:55, 9 April 2024
• Reverb block
  .... Typical plates are around 25-50%. Set to higher values to exaggerate the effect. Stereo imaging is adjustable via the Pickup Spacing parameter. ...essor in extreme use situations. Therefore, when viewing a Delay or Reverb effect editing GUI screen on the FM9 hardware, a CPU meter will appear on the disp
  29 KB (4,411 words) - 16:12, 16 April 2024
• Firmware release notes - FM9
  .... Typical plates are around 25-50%. Set to higher values to exaggerate the effect. Stereo imaging is adjustable via the “Pickup Spacing” parameter. * AMP effect now has 32 less sample times of latency.
  50 KB (7,888 words) - 18:24, 15 April 2024
• Firmware release notes - AX8
  AX8 V7.02 adds MOTOR DRIVE to the AMP block, as well as some effect block enhancements. ...he unit always returns to the main screen. This prevents display issues in effect blocks. It is also consistent with the behavior of the Single Preset Footsw
  46 KB (7,455 words) - 11:00, 15 January 2024
• MIDI
  ...loading presets, enable mapping of Program Changes, and choose between two Effect Bypass modes. The MIDI settings are part of the system data which can be ba ==Effect Bypass Mode==
  43 KB (6,811 words) - 05:58, 1 March 2024
• Firmware release notes - FM3
  * Fixed crash in Synth effect under certain circumstances. ...100%, (e.g. wah, EQ, etc.) The new feature smooths the transition when the effect is turned on or off.
  56 KB (8,824 words) - 14:24, 30 April 2024
• Setup menu
  Boost/Pad is not intended for boosting USB output (although it does have that effect). Usually you will use this when you send the effect loop out before the amp block. The signal will be weak going to the D/A con
  18 KB (2,979 words) - 16:07, 16 April 2024
• MIDI SysEx
  ...ect-bypass-status-info-available.html SysEx commands for retrieving Preset/Effect bypass states] ...ormation about each effect block in preset follows, using 5 bytes for each effect block in the preset
  114 KB (16,586 words) - 23:11, 24 December 2023
• Axe-Fx II
  ...on the Recall screen: copy and paste effect settings with [[Presets|Recall Effect]]. * Assign a switch assigned to the effect's X/Y MIDI CC
  33 KB (5,066 words) - 10:51, 27 February 2024
• Noise gate
  ...the preset is set to “Off”, the global Noisegate Offset value will have no effect. The default value is 0 dB and is set to that upon a system reset.
  14 KB (2,052 words) - 17:09, 5 April 2024
• Cab block
  ...ffects is usually subtle. It depends on how non-linear or time-variant the effect is. For effects like EQ, which are linear and time-invariant, it doesn't ma [http://forum.fractalaudio.com/threads/no-effect-loop-in-axe-fx´s-amp-models.22802/#post-369849]
  86 KB (13,616 words) - 11:55, 23 April 2024
• FC-6 and FC-12 foot controllers
  The FC will sometimes briefly display messages, for example when turning an effect on and off. In the FC configuration you specify the on-display time for the ...s allows Channel switches to serve double duty by engaging or bypassing an effect. To use this option, stomp again on the footswitch for a currently selected
  27 KB (4,240 words) - 16:52, 16 April 2024
• FAMC Liquid Foot+
  | External Dev Sync- AXE-FX3: Change to a specific channel of a specific effect, or Change it's BYPASS STATE *** Under Sync Effect, Select: SCENE 1 and Click Yes, if you get the Auto-Program popup window
  125 KB (20,342 words) - 08:20, 25 March 2022

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)