Template:MFC And AxeEdit Working Together

Getting the MFC-101 and AxeEdit working together

There was a [lengthy] MIDI Merge thread on this subject on the FAS forum, so thought it should be added to the wiki for preservation sake, as I'm sure here are MANY folks who would like to get this working. This page explains what to do to get AxeEdit and the MFC-101 working with the Axe at the SAME TIME.

BASICS

NOTE: 'This article assumes use of the equipment listed below. Different choices for your midi merger will likely require a different approach.'

• To get started will need the following equipment:
  • midi merge box [eg: Midi Solutions Midi Merge]
  • midi interface to PC [eg: M-Audio Anniv 2x2]
  • 3 or 4 5-pin midi cables [eg: any standard 5-pin midi cable]
  • 7-pin to 5-pin midi cable

NOTE: 'Guitar-cable.com offers the 7-to-5-pin + 2.5mm jack cable which is shown in the merge diagrams below. <a href="http://best-tronics.com/mm5/merchant.mvc?Screen=PROD&Store_Code=BMI&Product_Code=MIDI57C-XX&Attributes=Yes&Quantity=1">Click here to order part # MIDI57C-XX</a>. Build quality is excellent.'

THE BIG Picture

The following TWO pictures show different ways to achieve the same objective. BOTH use the "modified" midi-merger box - which is explained below. The first approach uses uses a 7-pin to 5-pin cable that supplies power to the MFC and the second uses a standard 5-pin midi cable powering the MFC directly from its own adapter.

WARNING! MODIFYING OR EVEN OPENING A MIDI SOLUTIONS MERGER WILL VOID ITS WARRANTY!

The First Method

The first (and original) approach - Matman's method - uses a 7-pin to 5-pin midi cable modified to connect the power to the MFC-101.

1. Credit to Matman for above pic

The Second Method

The second picture is how mine is setup using standard 5-pin midi cables - as I did not have a 7-pin to 5-pin cable.

Modified MIDI-MERGE Box

The modification shown below is necessary to allow the MFC and Axe to communicate with each other. Without this mod, the Tuner, Tap Tempo and Patch names will not be displayed on the MFC. The Axe's midi IN port is actually bi-directional, you will need to connect midi ports 1&3 on either the IN1 in IN2 sockets (your choice) to the 1&3 pins on the OUT port of the merge box to make them talk to each other correctly.

"The merger-box has four screws under the "MIDI Solution" Sticker - so don't break your box to get through to the PCB, just pull of the sticker and unscrew the top. Then lift the PCB out of the box - it's not glued or screwed - and solder cables from the IN port (I chose IN2 because phantom power comes from my MOTU) of your choice to the OUT port (Pin 1&3) on the downside of the PCB. Pin 1&3 are the outside pins of the socket.They aren't connected to anything."

1. Credit to Michael for the pics below and description inside quotes above

This process should work for most "like" products, assuming you chose not to use the Midi Solutions merge box.

Alternative Solution for Mac/Emu Users

The following solution was provided by Paolo68 for Mac users with and Emu interface.

Per joe1871 - "Anybody else out there looking to get the MFC working with the Axe and your PC get Paolo's doc, and a MIDI Solutions Merger and MIDI Solutions Thru (I got the Quadra Merger and Quadra Thru. Folllow the doc, then launch the Axe PX app. Go in and select the channels you used on your MIDI IF and you have USB working on the PC. No more swapping cables! (Granted I only swapped cables for a couple of days, but it was a PITA that I am glad to be free of)."