Search results

Jump to navigation Jump to search
  • ...into the loop of a [[Delay]] block. The [[Feedback_send/return|Feedback]] blocks need to be used, in conjunction with some unusual routing. =====Effect on dry signal=====
    2 KB (368 words) - 17:45, 30 August 2008
  • ...e difference between the left and right channels. Adjust until the desired effect is achieved. Certain frequencies may cancel each other at various settings, *'''PAN''' - Sometimes the effect will cause a shift in the apparent localization of the instrument. The pan
    1,012 bytes (155 words) - 05:12, 27 September 2008
  • ...s to a row in the routing matrix. To adjust, for example, the gain for the effect in row two preceding this block, simply adjust '''GAIN2'''. ...rd left, the other panned hard right. You can now fade between the two amp blocks using the '''PAN''' control. Attach the '''BALANCE''' control to a modifier
    1 KB (175 words) - 01:06, 2 June 2010
  • The Feedback Send and Return blocks allow you to feedback sound from one point in the routing to any other poin ''Warning: Use caution with the Feedback blocks as you can easily program an unstable loop and cause internal clipping of t
    2 KB (379 words) - 17:35, 30 August 2008
  • ...d tones from the input. The Axe-Fx Ring Modulator differs from the classic effect in that the frequency can be controlled by the pitch of the input. [[Category:Effect blocks]]
    765 bytes (118 words) - 09:04, 10 June 2007
  • !colspan=3| '''Effect Block Count and Type Differences in Axe-Fx Products''' ! Effect
    2 KB (217 words) - 14:52, 30 August 2010
  • ...Drive]] or [[Amp]] block. For a simple volume boost, place it after those blocks or at the very end of the chain. Keep in mind the boost will push the driv
    548 bytes (99 words) - 04:30, 22 May 2008
  • ...of time that the waveform is "on" as opposed to "off". This control has no effect for sine, log, exp or random waveforms [[Category:Effect blocks]]
    2 KB (284 words) - 09:06, 10 June 2007
  • [[Category:Effect blocks]]
    478 bytes (78 words) - 19:03, 16 August 2008
  • ...tar amp (or head and cabinet) place the loop BEFORE any cabinet simulation blocks. For example, if you want to send a fully processed, stereo feed to the P.A [[Category:Effect blocks]]
    1 KB (252 words) - 07:05, 10 June 2007
  • ..., the unique control input processing of the Axe-Fx eliminates the "zipper effect" common to many remotely controlled wahs. [[Category:Effect blocks]]
    2 KB (351 words) - 23:09, 30 June 2009
  • ...le effect. It is always connected directly to the main inputs. To edit the effect go to the page in the menu. The Noise Gate is always active but can be de [[Category:Effect blocks]]
    1 KB (187 words) - 19:17, 6 October 2009
  • ...ob twisting is done via an LFO and there is no dry sound to water down the effect. Perusing the Axe-Fx's available effect blocks, the chorus is the best fit for this task. Compared to the delay block, the
    1 KB (262 words) - 13:30, 7 August 2008
  • ...p delay line with paramteric control of time, amplitude, and panning. This effect can be used to create interesting delay patterns or as a “density increas *'''INPUT GAIN''' - Sets the input level to the effect. Attach this to an expression pedal or controller to produce swell effects.
    2 KB (270 words) - 08:58, 10 June 2007
  • [[Category:Effect blocks]]
    766 bytes (132 words) - 14:36, 27 December 2008
  • ...s the resonance of the filters. Higher resonance can yield a more dramatic effect. [[Category:Effect blocks]]
    2 KB (279 words) - 08:56, 10 June 2007
  • The Axe-Fx Ultra Quad Chorus is the ultimate chorus effect. Four independent chorus units are modulated by four separate LFO’s. The ...e fourth LFO modulates all the chorus units. In the illustration above the effect is shown in the default stereo configuration. The four LFO’s are depicted
    3 KB (533 words) - 08:54, 10 June 2007
  • ...Phaser also contains a special “Vibe Mode” that recreates the classic vibe effect with astonishing accuracy. Set the ORDER control to fully clockwise to acti ''NOTE: The '''MIX''' control should be set at 50% for the maximum effect.''
    3 KB (420 words) - 16:08, 3 September 2008
  • straightforward. There are three basic steps: placement, routing and effect editing. ...effect at this grid position use the value dial. As you turn the dial the effect type is
    12 KB (2,161 words) - 04:13, 17 April 2008
  • ...ob twisting is done via an LFO and there is no dry sound to water down the effect. Perusing the Axe-Fx's available effect blocks, the chorus is the best fit for this task. Compared to the delay block, the
    1 KB (235 words) - 17:42, 3 January 2010

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)