Axe-Fx SysEx Documentation

Axe-Fx System Exclusive Message Spec

This is a user-driven project to document the SysEx messages used by the Axe-Fx. For a list of controllers capable of sending (and possible receiving) SysEx information to your Axe-Fx please see [SysEx Capable Controllers].

Disclaimer

Use of the SysEx messages to access your Axe-Fx is not supported by Fractal Audio. You use these messages at your own risk.

The SysEx messages are copyright Fractal Audio and are printed here with the permission of Fractal Audio.

When in doubt: ask questions in the forum before using this stuff.

General SysEx Message Overview

(Attempting to describe the general format of the SysEx messages used by the Axe-Fx here. Please expand this!)

A sample Axe-Fx SysEx message (10.3 firmware):

Message: F0  00  01  74  01  02 0A 06 00 00 01 00 01  F7
Block:   1   2   3   4   5  (--------- data --------) 7

SysEx Message Blocks Described

Block	Description
1	SysEx Start byte. From the GM spec. Indicates the start of a MIDI SysEx message.
2	Manufacturer sysex ID byte 0. As of firmware 8.02 this is always 00.
3	Manufacturer sysex ID byte 1. As of firmware 10.02, this is always 01 (in previous firmware versions this was 00).
4	Manufacture sysex ID byte 2. As of firmware 10.02, this is 74 (in previous firmware versions this was 7D). If you're sending messages this should be set to the SysEx ID of your Axe-Fx. Failing to set this to the SysEx ID of the target unit will see all your SysEx messages ignored by the unit. This is true for patch dumps as well.
5	MIDI device ID
data	The data portion of the SysEx message. You construct this portion using the tables below. The first two bytes are used to indicate the effect block or feature on the Axe-Fx being accessed.
7	SysEx End byte.

Axe-Fx Sysex Message Formats

reformatted from Axe-Fx MIDI Remote Programming, courtesy of Cliff Chase/Fractal Audio

warning: this document was from an early stage in the Axe's development, so some things may have changed

***REMINDER: THIS IS NOT SUPPORTED BY FRACTAL AUDIO - DO NOT ASK THEM FOR HELP, AND USE AT YOUR OWN RISK***

Introduction

The Axe-Fx allows remote programming via it's MIDI interface. To utilize this feature the remote programmer (PC) is connected to the Axe-Fx MIDI in and out jacks. Commands are sent to the MIDI in and replies are returned from MIDI out.

There are only two basic objects in the Axe-Fx: effects and modifiers. Effects include all effect objects and modifiers are the transform between an internal or external controller and an effect parameter. All effects have a unique effect ID and all modifiers have a unique ID.

All parameters in the Axe-Fx are stored as 8-bit values with a range of 0 to 254 (255 not used). Axe-Fx parameters fall into 3 different types: integer, linear and log. Integer parameters have a direct correspondence between the parameter value and the parameter itself. Linear parameters have a linear relationship between the parameter value and the parameter itself. Log parameters have an exponential relationship between the parameter value and the parameter itself. Integer parameters typically have a limited range of allowable values.

All MIDI functions have the same header as follows:

0xF0 sysex start

0x00 Manf. ID byte0

0x00 Manf. ID byte1

0x7d Manf. ID byte2 (this value is configurable within the Axe-Fx)

0x00 Model #

0xdd Function ID

Byte2 of the manufacturers ID is configurable in the Axe-Fx on the MIDI menu. This value should match or the Axe-Fx may reject the message. The function ID indicates the type of function and sets the formatting of the data to follow.

Note from iaresee: When they say "this value is configurable on the Axe-Fx" they're talking about the SysEx ID. This byte in the message is the SysEx ID of your unit. If it doesn't match with what you've set on your unit the message is ignored by it.

MIDI Send Messages

These messages are sent to the Axe-Fx to carry out an action.

The following functions are available:

MIDI_SET_PARAMETER

This function sets or queries an effect parameter.

Format:

0xF0 sysex start

0x00 Manf. ID byte0

0x00 Manf. ID byte1

0x7d Manf. ID byte2 (this value is configurable within the Axe-Fx)

0x00 Model #

0x02 Function ID

0xdd effect ID LS nibble

0xdd effect ID MS nibble

0xdd parameter ID LS nibble

0xdd parameter ID MS nibble

0xdd parameter value LS nibble

0xdd parameter value MS nibble

0xdd query(0) or set(1) value

0xF7 sysex end

The effect identified by the effect ID has its parameter identified by the parameter ID set to a value of between 0 and 254. You can query the current value by setting or clearing the set byte.

Rather than trying to keep track of the range of all parameters and their types this MIDI function operates as a virtual interface. After calling MIDI_SET_PARAM the Axe-Fx responds with the actual parameter value and a string representation of the parameter.

For example, if setting a rate parameter the Axe-Fx will respond with the parameter value (0 - 254) and a string representing the actual value of the rate, i.e. "1.234 Hz".

The value response allows querying a parameter and also does range checking on integer types. If one attempts to set an integer type outside of its range the Axe-Fx will set the value to the minimum or maximum value allowable and respond with the actual value set.

Values can be queried by simply setting the set/query byte to 0. The parameter value is irrelevant. The Axe-Fx will then respond with the current value and string representation.

When first editing an effect all the parameters should be queried to determine their current values. To then edit a parameter simply send the new parameter value and await the response.

MIDI_SET_MODIFIER

This function sets or queries a modifier parameter.

Message format:

0xF0 sysex start

0x00 Manf. ID byte0

0x00 Manf. ID byte1

0x7d Manf. ID byte2 (this value is configurable within the Axe-Fx)

0x00 Model #

0x07 Function ID

0xdd effect ID LS nibble

0xdd effect ID MS nibble

0xdd parameter ID LS nibble

0xdd parameter ID MS nibble

0xdd modifier parameter ID LS nibble

0xdd modifier parameter ID MS nibble

0xdd modifier value LS nibble

0xdd modifier value MS nibble

0xdd query(0) or set(1) value

0xF7 sysex end

This function sets the value of a modifier parameter. The modifier parameter identified by its ID has its value set to the modifier value. The effect being controlled and the parameter being controlled are indicated by the effect and parameter ID's. Note that the effect parameter ID will be different than the basic parameter ID. For example, a rate control may have a parameter ID = 3. To control it in real-time via a modifier the corresponding parameter ID will be different. Modifiable parameters have a corresponding parameter with an ID greater than or equal to 100.

There are 16 modifiers available in the Axe-Fx, meaning that up to 16 parameters can be controlled at one time. A modifier is connected to a parameter when the modifier control ID is nonzero. To connect a modifier to a parameter call this function with the desired effect ID and parameter ID with the modifier parameter equal to MOD_CTRTLID and a modifier value equal to the desired controller. A non-zero value will automatically connect the modifier. A value of zero will disconnect the modifier.

Once a modifier is connected the other parameters can be set or queried accordingly. Like the MIDI_SET_PARAMETER function this function responds with the value set and a text string representation of the actual value.

MIDI_PLACE_EFFECT

Places an effect at a position in the effects grid.

Message format:

0xF0 sysex start

0x00 Manf. ID byte0

0x00 Manf. ID byte1

0x7d Manf. ID byte2 (this value is configurable within the Axe-Fx)

0x00 Model #

0x05 Function ID

0xdd effect ID LS nibble

0xdd effect ID MS nibble

0xdd grid position

0xdd query(0) or set(1) value

0xF7 sysex end

The effect identified by its ID is placed at a position in the grid. The grid is 4 rows by 12 columns. A grid position is given by position = 4 * column_number + row_number. Rows and columns are enumerated starting with zero.

If another effect is at the position it is removed.

MIDI_CONNECT_EFFECT

Connects two effects.

Message format:

0xF0 sysex start

0x00 Manf. ID byte0

0x00 Manf. ID byte1

0x7d Manf. ID byte2 (this value is configurable within the Axe-Fx)

0x00 Model #

0x06 Function ID

0xdd source position

0xdd destination position

0xdd connect (1) | disconnect (0)

The effect at the source position is connected or disconnected to/from the effect at the destination position. The position is as described above. A null block cannot be one of the two effects being connected and will result in the function failing.

MIDI_GET_FIRMWARE_VERSION

Query installed version of firwmare.

Message format:

0xF0 sysex start

0x00 Manf. ID byte0

0x01 Manf. ID byte1

0x74 Manf. ID byte2 (this value is configurable within the Axe-Fx)

0x01 Model #

0x08 Function ID

0xF7 sysex end

The device will respond with the firmware version. For example, 10.3 is reported as: F0 00 01 74 01 08 0A 03 F7

MIDI Return Messages

Upon sending a message to the Axe-Fx it will return a message. The following return messages are implemented:

MIDI_PARAM_VALUE

Message format:

0xF0 sysex start

0x00 Manf. ID byte0

0x00 Manf. ID byte1

0x7d Manf. ID byte2 (this value is configurable within the Axe-Fx)

0x00 Model #

0x02 Function ID (2)

0xdd effect ID LS nibble

0xdd effect ID MS nibble

0xdd parameter ID LS nibble

0xdd parameter ID MS nibble

0xdd parameter value LS nibble

0xdd parameter value MS nibble

0xdd null-terminated string byte0

0xdd byte1

...

0x00 null character

0xF7 sysex end

This message is returned after sending the MIDI_SET_PARAMETER message.

MIDI_MODIFIER_VALUE

Message format:

0xF0 sysex start

0x00 Manf. ID byte0

0x00 Manf. ID byte1

0x7d Manf. ID byte2 (this value is configurable within the Axe-Fx)

0x00 Model #

0x07 Function ID (7)

0xdd effect ID LS nibble

0xdd effect ID MS nibble

0xdd parameter ID LS nibble

0xdd parameter ID MS nibble

0xdd modifier parameter ID LS nibble

0xdd modifier parameter ID MS nibble

0xdd modifier value LS nibble

0xdd modifier value MS nibble

0xdd null-terminated string byte0

0xdd byte1

...

0x00 null character

0xF7 sysex end

This message is returned after sending the MIDI_SET_MODIFIER message.

MIDI_STATUS

Reports success or failure.

Message format:

0xF0 sysex start

0x00 Manf. ID byte0

0x00 Manf. ID byte1

0x7d Manf. ID byte2 (this value is configurable within the Axe-Fx)

0x00 Model #

0xdd Calling Function ID

0xdd status

0xF7 sysex end

All other function calls respond with this message. The calling function ID is indicated and success (1) or failure (0) indicated in the status byte.

MIDI Realtime Sysex Messages

Realtime sysex messages for tempo and tuner info are sent by default. They can be disabled in the IO / MIDI / SEND REALTIME SYSEX menu.

MIDI_TUNER_INFO

When the tuner is active this message is streamed to the MIDI out port.

Message format:

0xF0 sysex start

0x00 Manf. ID byte0

0x00 Manf. ID byte1

0x7d Manf. ID byte2 (this value is configurable within the Axe-Fx)

0x00 Model #

0x0d Calling Function ID

0x?? Note value (0 = A, 1 = A#, 2 = B, 3 = C etc)

0x?? Note octave

0x?? Fine tune (0 = very flat, 0x7f - very sharp, 0x3f/0x40? - in tune)

0xF7 sysex end

MIDI_TEMPO_BEAT

Tempo beats (corresponding to the blinking tempo LED) are streamed to the MIDI out port.

Message format:

0xF0 sysex start

0x00 Manf. ID byte0

0x01 Manf. ID byte1

0x74 Manf. ID byte2 (this value is configurable within the Axe-Fx)

0x01 Model #

0x10 Tempo function ID

0xF7 sysex end

Parameter Numbers

IDs listed below are as of firmware revision 8.02

For firmware 10.3, see the default.axeml file included with Axe-Edit for a complete list of Effect Block and Parameter IDs as described in this forum post.

Effect Block IDs

Common

00 06 =

01 06 =

02 06 =

03 06 =

04 06 = Comp1

05 06 = Comp2

06 06 = GEQ1

07 06 = GEQ2

08 06 = PEQ1

09 06 = PEQ2

0A 06 = Amp1

0B 06 = Amp2

0C 06 = Cab1

0D 06 = Cab2

0E 06 = Reverb1

0F 06 = Reverb2

00 07 = Delay1

01 07 = Delay2

02 07 = Multi-Delay1

03 07 = Multi-Delay2

04 07 = Chorus1

05 07 = Chorus2

06 07 = Flanger1

07 07 = Flanger2

08 07 = Rotary1

09 07 = Rotary2

0A 07 = Phaser1

0B 07 = Phaser2

0C 07 = Wah1

0D 07 = Wah2

0E 07 = Formant

0F 07 = Volume/Pan

00 08 = Tremolo/Pan1

01 08 = Tremolo/Pan2

02 08 = Pitch

03 08 = Filter1

04 08 = Filter2

05 08 = Drive1

06 08 = Drive2

07 08 = Enhancer

08 08 = FX Loop

09 08 = Mixer1

0A 08 = Mixer2

0B 08 =

0C 08 =

0D 08 =

0E 08 = Feedback Send

0F 08 = Feedback Return

Ultra-Only

00 09 = Synth1

01 09 = Synth2

02 09 = Vocoder

03 09 = MegaTap Delay

04 09 = Crossover1

05 09 = Crossover2

06 09 = Gate/Exp1

07 09 = Gate/Exp2

08 09 = Ring Mod

09 09 = Pitch2

0A 09 = MBC1

0B 09 = MBC2

0C 09 = QuadCho1

0D 09 = QuadCho2

0E 09 = Resonator1

0F 09 = Resonator2

00 0A = GEQ3

01 0A = GEQ4

02 0A = PEQ3

03 0A = PEQ4

04 0A = Filter3

05 0A = Filter4

06 0A = Vol/Pan2

07 0A = Vol/Pan3

08 0A = Vol/Pan4

Amp Block Parameters

00 00 = Type

01 00 = Drive

02 00 = Bass

03 00 = Mids

04 00 = Treble

05 00 = Master Volume

06 00 = Low Cut

07 00 = Hi Cut

08 00 = Tonestack Frequency

09 00 =

0A 00 = Bright Cap

0B 00 =

0C 00 = Xformer LF

0D 00 = Xformer HF

0E 00 = Tonestack Location

0F 00 = Input Select

00 01 = Deep

01 01 =

02 01 =

03 01 = Sag

04 01 = Presence

05 01 = Level

06 01 = Balance

07 01 = Bypass Mode

08 01 = Damping

09 01 = Presence Frequency

0A 01 = Speaker Resonance Freq

0B 01 = Transformer Match (Depth)

0C 01 = Bright Switch & Boost Switch

0D 01 = Warmth

0E 01 = Thump

0F 01 = Global Amp

00 02 =

01 02 = Stabilizer

02 02 = Tonestack Type

03 02 = B+ Capacitance

04 02 = Bias

Cab Block Parameters

00 00 = Cab (L)

01 00 = Mic (L)

02 00 = Cab R

03 00 = Mic R

04 00 = Link off/on

05 00 = Level L

06 00 = Level R

07 00 = Pan L

08 00 = Pan R

09 00 = Level

0A 00 = Balance

0B 00 = Bypass Mode

0C 00 = Type

00 00 = Mono HiRes

01 00 = Mono LoRes

02 00 = Stereo

0D 00 =

0E 00 = Drive (L)

0F 00 = Drive R

Chorus Block Parameters

04 07 = Chorus1

05 07 = Chorus2

00 00 = Voices

01 00 = Rate

02 00 = Tempo

03 00 = Depth

04 00 = Bass

05 00 = Treble

06 00 = Bass Freq

07 00 = Treble Freq

08 00 = Delay Time

09 00 = LFO Phase

0A 00 = LFO Type

0B 00 = Auto Depth off/on

0C 00 = Mix

0D 00 = Level

0E 00 = Balance

0F 00 = Bypass Mode

00 01 = Global Mix

01 01 = Phase Reverse

02 01 =

03 01 = Width

04 01 = LFO2 Rate

05 01 = LFO2 Depth

Comp Block Parameters

04 06 = Comp1

05 06 = Comp2

00 00 = Threshold

01 00 = Compression

02 00 = Attack

03 00 = Release

04 00 = Level

05 00 = Knee

06 00 = Makeup Switch

07 00 = Detect

08 00 = Filter

09 00 =

0A 00 = SCSEL

0B 00 = Mix

0C 00 = Type (Studio/Pedal)

Delay Block Parameters

00 07 = Delay1

01 07 = Delay2

00 00 = Type

01 00 = Time MSB?

02 00 = Time LSB?

03 00 = Ratio (Stereo)

04 00 = Feedback (Mono)

05 00 = Feedback L

06 00 = Feedback R

07 00 = Echo Pan

08 00 = Spread

09 00 = Tempo

0A 00 = Lowcut

0B 00 = High cut

0C 00 = LFO1 Rate

0D 00 = LFO2 Rate

0E 00 = LFO1 Depth

0F 00 = LFO2 Depth

00 01 = Drive

01 01 = Mix

02 01 = Level

03 01 = Pan

04 01 = Bypass Mode

05 01 = Global Mix

06 01 =

07 01 = In Gain

08 01 = LFO1 Type

09 01 = LFO2 Type

0A 01 = Time R (Dual) MSB?

0B 01 = Time R (Dual) LSB?

0C 01 = Master Feedback

0D 01 = Tempo R (Dual)

0E 01 = Feedback LR (Dual)

0F 01 = Feedback RL (Dual)

00 02 = Level L (Dual)

01 02 = Level R (Dual)

02 02 = Pan L (Dual)

03 02 = Pan R (Dual)

04 02 = LFO1 Phase

05 02 = LFO2 Phase

06 02 = XFade Time (Rev)

07 02 = Run (Reverse)

08 02 = Trig Restart (Reverse)

09 02 = Filter Slope

0A 02 = Ducker Att

0B 02 = Threshold

0C 02 = Release Rate

0D 02 = Depth Range

0E 02 = Diffusion

0F 02 = Diff Time

00 03 = Phase Rev

01 03 = LFO1 Target

02 03 = LFO2 Target

03 03 = LFO1 Tempo

04 03 = LFO2 Tempo

Drive Block Parameters

Please note: this does not match with firmware 8.02 and all of this section needs updating.

05 08 = Drive1

06 08 = Drive2

00 00 = Type?

01 00 = Drive

02 00 = Tone

03 00 = Level

04 00 = Mix

05 00 = Bypass Mode

06 00 = Slew Limit

07 00 =

08 00 = Low Cut

09 00 = High Cut

0A 00 = Clip Type

0B 00 = Bias

Filter Block Parameters

03 08 = Filter1

04 08 = Filter2

00 00 = Type

01 00 = Freq

02 00 = Q

03 00 = Gain

04 00 = Level

05 00 = Balance

06 00 = Bypass Mode

07 00 = R Offset

08 00 =

09 00 = Pan L

0A 00 = Pan R

Flanger Block Parameters

06 07 = Flanger1

07 07 = Flanger2

00 00 = Rate

01 00 = Tempo

02 00 = Depth

03 00 = Feedback

04 00 = Bass

05 00 = Treble

06 00 = Bass Freq

07 00 = Treble Freq

08 00 = Time

09 00 = Manual

0A 00 = LFO Phase

0B 00 = LFO Type

0C 00 = LFO Hicut

0D 00 = Auto Depth

0E 00 = Mix

0F 00 = Level

00 01 = Balance

01 01 = Bypass Mode

02 01 = Global Mix

03 01 =

04 01 = Phase Reverse

05 01 = Dry Delay

Graphic EQ Block Parameters

06 06 = GEQ1

07 06 = GEQ2

00 00 = 63

01 00 = 125

02 00 = 250

03 00 = 500

04 00 = 1K

05 00 = 2K

06 00 = 4K

07 00 = 8K

08 00 =

09 00 = Level

0A 00 = Balance

0B 00 = Bypass Mode

Mixer Block Parameters

09 08 = Mixer1

0A 08 = Mixer2

00 00 = Gain1

01 00 = Gain2

02 00 = Gain3

03 00 = Gain4

04 00 = Pan1

05 00 = Pan2

06 00 = Pan3

07 00 = Pan4

08 00 = Master Level

09 00 = Output Mode

Parametric EQ Block Parameters

08 06 = PEQ1

09 06 = PEQ2

00 00 = Freq1

01 00 = Freq2

02 00 = Freq3

03 00 = Freq4

04 00 = Freq5

05 00 = Q1

06 00 = Q2

07 00 = Q3

08 00 = Q4

09 00 = Q5

0A 00 = Gain1

0B 00 = Gain2

0C 00 = Gain3

0D 00 = Gain4

0E 00 = Gain5

0F 00 =

00 01 = Level

01 01 = Pan

02 01 = Bypass Mode

03 01 =

04 01 = Type 1 (Low)

00 00 = Shelving

01 00 = Peaking

02 00 = Blocking

05 01 = Type 5 (High)

Parametric EQ Block Parameters

08 06 = PEQ1

09 06 = PEQ2

00 00 = Freq1

01 00 = Freq2

02 00 = Freq3

03 00 = Freq4

04 00 = Freq5

05 00 = Q1

06 00 = Q2

07 00 = Q3

08 00 = Q4

09 00 = Q5

0A 00 = Gain1

0B 00 = Gain2

0C 00 = Gain3

0D 00 = Gain4

0E 00 = Gain5

0F 00 =

00 01 = Level

01 01 = Pan

02 01 = Bypass Mode

03 01 =

04 01 = Type 1 (Low)

00 00 = Shelving

01 00 = Peaking

02 00 = Blocking

05 01 = Type 5 (High)