Search results

Create the page "Connecting" on this wiki! See also the search results found.

• Scene MIDI block
  ...so use the Scene MIDI block to send MIDI commands to the device itself, by connecting MIDI OUT to MIDI IN.
  1 KB (221 words) - 11:41, 9 April 2024
• Mono and stereo signal
  ...f-Stereo''' – Leaving the Axe‐Fx III in its default stereo conguration but connecting only one (Left) output results in a “half‐stereo” setup. This works f When connecting the left and right outputs of the processor to a mixer, make sure that the
  5 KB (844 words) - 22:53, 1 March 2024
• FASLINK
  ...o need to power down the modeler when connecting the FC controller, <q>hot connecting</q> is supported.
  7 KB (1,087 words) - 21:47, 25 February 2024
• Setup menu
  ...is parameter to LEFT ONLY (default). You'd only use SUM L+R or STEREO when connecting a stereo instrument to Input 1 (rear). Input 1 front on the Axe-Fx III is a ...f-Stereo''' – Leaving the Axe‐Fx III in its default stereo conguration but connecting only one (Left) output results in a “half‐stereo” setup. This works f
  18 KB (2,979 words) - 16:07, 16 April 2024
• Humbuster
  WARNING: When connecting a Humbuster output to a [[I/O_connectivity_and_levels#Balanced_and_unbalanc
  3 KB (529 words) - 22:20, 27 February 2024
• CPU usage
  ...02] If a preset uses much CPU, you may run into CPU overload problems when connecting the hardware to a computer through USB.[http://forum.fractalaudio.com/threa ; USB : Connecting USB increases CPU usage (not on Axe-Fx III and FM9).
  15 KB (2,310 words) - 20:39, 29 March 2024
• Output block
  ...FM9 devices, even with the Level parameter at 0. This can be monitored by connecting the Input 1 block directly to the Output 1 block and looking at the meter i
  4 KB (701 words) - 14:46, 2 March 2024
• X-Load LB-2 Reactive Load Box
  ...live use or recording. It allows you to use a traditional tube amp without connecting a speaker cabinet. The X-Load LB-2 provides an 8Ω load (100W maximum) whil : Connecting a speaker to this output jack disconnects the internal load and connects th
  16 KB (2,470 words) - 12:36, 8 April 2024
• Digital I/O and computer audio
  [https://forum.fractalaudio.com/threads/newbie-having-trouble-connecting-axe-iii-to-my-pmc-two-two-6-speakers.163885/post-1964817] ==When connecting to the DAW drops the volume or puts the device into bypass mode==
  25 KB (3,935 words) - 17:02, 16 April 2024
• FX8
  ...hassis it wouldn't necessarily blow a fuse and you could get electrocuted. Connecting the chassis to ground ensures that the circuit breaker will trip in the eve ...hassis it wouldn't necessarily blow a fuse and you could get electrocuted. Connecting the chassis to ground ensures that the circuit breaker will trip in the eve
  33 KB (5,417 words) - 00:24, 3 January 2024
• USB
  ...interface in most cases. An external audio interface is required only when connecting the analog Axe-Fx II outputs to a computer. Directly connecting the USB-B port on a device to a computer with an onboard USB type C port, l
  27 KB (4,137 words) - 13:29, 8 April 2024
• FC-6 and FC-12 foot controllers
  The FC controllers allow connecting up to four expression pedals with TRS cables. You can assign functions to t The FC controllers allow connecting up to four external switches. Use a TS cable for a single switch (all devic
  27 KB (4,240 words) - 16:52, 16 April 2024
• MFC-101 MIDI foot controller
  ...IDI. It provides power from the Axe-Fx II to the MFC-101 without requiring connecting the power supply to the Axe-Fx II, transmits MIDI data and tuner and tempo ...d XL+. A regular XLR (microphone) cable powers the MFC and transfers data. Connecting the power supply to the Axe-Fx II is not required.
  32 KB (5,363 words) - 17:42, 12 January 2024
• Firmware release notes - FM3
  ...-ohm output you would set Speaker Impedance to 0.5. Conversely to simulate connecting a 16-ohm speaker you would set it to 2.0. To use FM3 Out 2 in unity gain applications, such as when connecting to a tube amp or certain pedals, confirm the following settings in the "Out
  48 KB (7,631 words) - 16:33, 15 April 2024
• MIDI
  ...ut voltage: WIDI Master is getting hot]</q> about the FM3 getting hot when connecting a wireless MIDI adapter for more information. ...ng a digitally encoded protocol, essentially a language. It is a method of connecting together MIDI-capable musical instruments or devices so that they can use a
  43 KB (6,811 words) - 05:58, 1 March 2024
• Axe-Fx II
  ...is the addition of an EtherCon jack, replacing the standard RJ45 port for connecting an MFC-101. This is in line with the MFC-101 Mark II version. EtherCon offe Use the I/O menu to tell the hardware what type of external switch you're connecting:
  33 KB (5,066 words) - 10:51, 27 February 2024
• Firmware release notes - FM9
  ...-ohm output you would set Speaker Impedance to 0.5. Conversely to simulate connecting a 16-ohm speaker you would set it to 2.0. ...ohm output you would set Speaker Impedance to 0.5. Conversely to simulate connecting a 16-ohm speaker you would set it to 2.0.
  50 KB (7,888 words) - 18:24, 15 April 2024
• Tone Match block
  ...he block using the FX Loop block. The Reference Source audition is done by connecting the expression pedal to the Ref Solo parameter. When Ref Solo is on the sel
  21 KB (3,490 words) - 17:23, 8 April 2024
• Amp modeling techniques
  ...-ohm output you would set Speaker Impedance to 0.5. Conversely to simulate connecting a 16-ohm speaker you would set it to 2.0. ...ng the relative impedance of the virtual speaker. For example, to simulate connecting a 16-ohm speaker to an 8-ohm output set Speaker Impedance to 2.0. Transform
  89 KB (14,048 words) - 18:07, 9 April 2024
• I/O connectivity and levels
  ; When does unity gain matter? : It is not important when connecting the device to an amplifier or mixing console. It is important in setups whe ...allows adapting a three-prong power cord to the old style outlet boxes by connecting the ground wire to the outlet box via the faceplate mounting screw. A cheat
  155 KB (25,257 words) - 16:49, 16 April 2024

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)