Always consult the official Owners Manuals first!
March 2024: all pages have been checked and are up-to-date

Difference between revisions of "FASLINK"

From Fractal Audio Wiki
Jump to navigation Jump to search
(45 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
__TOC__
 
__TOC__
 +
[[image:XLR.jpg|100px]]
 
=What is FASLINK=
 
=What is FASLINK=
  
FASLINK is a proprietary Fractal Audio communications link between the Axe-Fx series processors and the MFC-101 resp. FC controllers. FASLINK provides two-way communication through an XLR cable and phantom power. XLR cables (microphone cables) are common, flexible and robust, supporting runs of hundreds of feet.
+
FASLINK is a proprietary Fractal Audio communications link between the Axe-Fx II and the MFC-101 (FASLINK version 1), between the Axe-Fx III and FC controllers (FASLINK II), and between the FM3 and an FC controller (FASLINK II). FASLINK provides two-way communication and power via an XLR cable. XLR cables (microphone cables) are common, flexible and robust, supporting runs of hundreds of feet.
  
 
FASLINK replaces previous connection methods (MIDI and Ethernet).
 
FASLINK replaces previous connection methods (MIDI and Ethernet).
Line 8: Line 9:
 
There are two versions of FASLINK:
 
There are two versions of FASLINK:
  
* '''FASLINK (original)''' – Connects the Axe-Fx II and MFC-101.
+
'''FASLINK (original)''' – connects the Axe-Fx II and MFC-101
* '''FASLINK II''' – Connects the Axe-Fx III and FC foot controller(s), featuring a new protocol. Length limit is 100 feet ([http://forum.fractalaudio.com/threads/faslink-2-cable-length-limit.145778/#post-1723699 source]).
 
  
[[image:Iii-rear-transparent.png|400px]]
+
'''FASLINK II''' – connects the Axe-Fx III and FC foot controller(s), and the FM3 and FC foot controllers. It features a new protocol. Length limit is 100 feet ([http://forum.fractalaudio.com/threads/faslink-2-cable-length-limit.145778/#post-1723699 source])
  
=Which Fractal Audio products support FASLINK=
+
[[image:Iii-rear-transparent.png|300px]] [[image:FM3-rear.png|200px]]
  
'''Axe-Fx III''' – Built-in FASLINK II support.
+
<blockquote>"FASLINK is not a balanced protocol. But it is robust because it uses high signaling levels. You can use any wire for FASLINK but ideally it should be shielded and a heavy enough gauge to carry up to 1A without significant voltage drop. If "I" were adapting FASLINK to CAT5 I would use each pair as a conductor. I.e. blue and blue/white tied together as one conductor, green and green/white tied together as another conducter. Then the drain wire (and maybe another conductor pair to ensure low resistance) connected to the XLR shield. FASLINK uses two conductors plus shield (standard mic cable). One conductor is power. The other conductor is data. The shield is the common return for the two conductors. We've tested FASLINK over 100m of cable. As long as the conductors are heavy enough so the voltage doesn't drop too much you can run it very long distances." [http://forum.fractalaudio.com/threads/faslink-2-wiring.144095/#post-1755571 source]</blockquote>
  
'''Axe-Fx II XL and XL+''' – Built-in FASLINK support.
+
<blockquote>"The FASLINK port is protected against shorts." [http://forum.fractalaudio.com/threads/xl-lockup-when-faulty-faslink-xlr-is-connected.105500/#post-1262170 source]</blockquote>
 +
 
 +
<blockquote>"It's not standard MIDI. The Axe-Fx III uses a proprietary communication protocol. Devices can communicate over any physical layer by wrapping and unwrapping the comm protocol. Theoretically you can control it over MIDI, Ethernet, WiFi, RS-232, AppleTalk, Sneakernet, etc. The MIDI basics are there, of course, but to access the tuner, etc. you need to wrap and unwrap the protocol layer." [http://www.thegearpage.net/board/index.php?threads/just-got-my-axe-iii-invite-anyone-try-integrating-it-with-a-helix-as-foot-controller-yet.1952049/page-4#post-26744244 source]</blockquote>
 +
 
 +
=Supported by which products=
 +
 
 +
'''Axe-Fx III''' – supports FASLINK II
 +
 
 +
'''FM3''' – supports FASLINK II
 +
 
 +
'''Axe-Fx II XL and XL+''' – supports FASLINK
 +
 
 +
'''Axe-Fx II Mark I and II''' – requires FASLINK adapter to convert wiring from Ethernet/Ethercon to XLR
 +
 
 +
'''MFC-101 Mark III''' – supports FASLINK
 +
 
 +
'''MFC-101 Mark I and II''' – requires FASLINK adapter to convert wiring from Ethernet/Ethercon to XLR
 +
 
 +
'''FC controller''' – support FASLINK II
  
'''Axe-Fx II Mark I and II''' – FASLINK adapter needed to convert wiring from Ethernet/Ethercon to XLR.
+
=Set up a FASLINK connection=
  
'''MFC-101 Mark III''' – Built-in FASLINK support.
+
'''Axe-Fx III''' – connect the XLR cable between the Axe-Fx III and FC controller
  
'''MFC-101 Mark I and II''' – FASLINK adapter needed to convert wiring from Ethernet/Ethercon to XLR.
+
'''FM3''' – connect the XLR cable between the FM3 and FC controller
  
'''FC controllers''' – Built-in FASLINK II support.
+
'''Axe-Fx II''' – connect the XLR cable. Turn on FASLINK in the I/O menu
  
=Setting up FASLINK=
+
'''MFC-101''' – connect the XLR cable. Select the correct port in the MFC settings. Do NOT connect a power supply to the MFC-101 when using FASLINK
  
'''Axe-Fx III''' – Connect the XLR cable between the Axe-Fx III and FC controller. That's it.
+
=Provide power through FASLINK=
  
'''Axe-Fx II''' – Connect the XLR cable. Turn on FASLINK in the I/O menu.
+
A FASLINK II connection provides power (from the Axe-Fx III or FM3) to the first connected FC controller.
  
'''MFC-101''' – Connect the XLR cable. Select the correct port in the MFC settings. WARNING: do NOT connect a power supply to the MFC-101 when using FASLINK!
+
<blockquote>"The FC-12 uses more power because it has more LCDs. If the cable resistance is too high than there will be excessive voltage drop which could cause booting issues and other problems.
  
<blockquote>"The FASLINK port is protected against shorts." [http://forum.fractalaudio.com/threads/xl-lockup-when-faulty-faslink-xlr-is-connected.105500/#post-1262170 source]</blockquote>
+
Using a cable snake is not recommended because the conductor gauge is small and the resistance will be high. We recommend a good quality dedicated XLR cable. Dim LEDs are an indication that there is excessive voltage drop on the cable. The FC rated voltage is 9-12V but should work down to about 7V. If the snake is 100 ft. of 24 gauge wire then that would put you right at 7V. The FC-12 draws about 1A so Vdrop = 0.025 ohms/ft * 100 ft * 2 conductors * 1A = 5V drop. This is assuming the shield drain has the same resistance as the conductors. So, yeah, 100 ft snake is too long for an FC-12." [https://forum.fractalaudio.com/threads/fas-link-cable-run-works-for-fc-6-but-not-fc-12.154527/post-1838351 source]</blockquote>
  
=Adapters for older hardware=
+
=FASLINK adapters for older hardware=
  
The FASLINK XA-1 and XA-2 adapters convert the wiring on older Axe-Fx II and MFC-101 hardware (see above) from Ethernet/Ethercon to XLR. These adapters are "active" ([http://forum.fractalaudio.com/axe-fx-ii-discussion/95125-xa-1-faslink-adapter.html#post1139249 source]). They can be bought directly from [http://shop.fractalaudio.com Fractal Audio's online shop] and [http://g66.eu G66].
+
The FASLINK XA-1 and XA-2 adapters convert the wiring on older Axe-Fx II and MFC-101 hardware (see above) from Ethernet/Ethercon to XLR. These adapters are "active" ([http://forum.fractalaudio.com/axe-fx-ii-discussion/95125-xa-1-faslink-adapter.html#post1139249 source]). They can be bought directly from [http://shop.fractalaudio.com Fractal Audio's online shop] and [https://shop.g66.eu/fractal-audio/ G66].
  
 
The adapters do not support FASLINK II.
 
The adapters do not support FASLINK II.
  
[[file:XA-1 diagram.png]]  [[file:XA-2 diagram.png]]
+
[http://wiki.fractalaudio.com/axefx2/index.php?title=Owners_Manuals More information in the FASLINK Setup Guide]
  
 
[[file:FASLINK_adapters.png‎|150px|link=]]
 
[[file:FASLINK_adapters.png‎|150px|link=]]
  
[http://www.fractalaudio.com/downloads/manuals/faslink/FASLINK-Adapters-Setup-Guide.pdf More information in the FASLINK Setup Guide]
+
[[file:XA-1 diagram.png]]
 +
 
 +
[[file:XA-2 diagram.png]]
  
 
[[category:Axe-Fx2]]
 
[[category:Axe-Fx2]]
 
[[category:Axe-Fx3]]
 
[[category:Axe-Fx3]]
 +
[[category:FM3]]
 
[[category:Remote]]
 
[[category:Remote]]

Revision as of 08:11, 19 October 2019

XLR.jpg

What is FASLINK

FASLINK is a proprietary Fractal Audio communications link between the Axe-Fx II and the MFC-101 (FASLINK version 1), between the Axe-Fx III and FC controllers (FASLINK II), and between the FM3 and an FC controller (FASLINK II). FASLINK provides two-way communication and power via an XLR cable. XLR cables (microphone cables) are common, flexible and robust, supporting runs of hundreds of feet.

FASLINK replaces previous connection methods (MIDI and Ethernet).

There are two versions of FASLINK:

FASLINK (original) – connects the Axe-Fx II and MFC-101

FASLINK II – connects the Axe-Fx III and FC foot controller(s), and the FM3 and FC foot controllers. It features a new protocol. Length limit is 100 feet (source)

Iii-rear-transparent.png FM3-rear.png

"FASLINK is not a balanced protocol. But it is robust because it uses high signaling levels. You can use any wire for FASLINK but ideally it should be shielded and a heavy enough gauge to carry up to 1A without significant voltage drop. If "I" were adapting FASLINK to CAT5 I would use each pair as a conductor. I.e. blue and blue/white tied together as one conductor, green and green/white tied together as another conducter. Then the drain wire (and maybe another conductor pair to ensure low resistance) connected to the XLR shield. FASLINK uses two conductors plus shield (standard mic cable). One conductor is power. The other conductor is data. The shield is the common return for the two conductors. We've tested FASLINK over 100m of cable. As long as the conductors are heavy enough so the voltage doesn't drop too much you can run it very long distances." source

"The FASLINK port is protected against shorts." source

"It's not standard MIDI. The Axe-Fx III uses a proprietary communication protocol. Devices can communicate over any physical layer by wrapping and unwrapping the comm protocol. Theoretically you can control it over MIDI, Ethernet, WiFi, RS-232, AppleTalk, Sneakernet, etc. The MIDI basics are there, of course, but to access the tuner, etc. you need to wrap and unwrap the protocol layer." source

Supported by which products

Axe-Fx III – supports FASLINK II

FM3 – supports FASLINK II

Axe-Fx II XL and XL+ – supports FASLINK

Axe-Fx II Mark I and II – requires FASLINK adapter to convert wiring from Ethernet/Ethercon to XLR

MFC-101 Mark III – supports FASLINK

MFC-101 Mark I and II – requires FASLINK adapter to convert wiring from Ethernet/Ethercon to XLR

FC controller – support FASLINK II

Set up a FASLINK connection

Axe-Fx III – connect the XLR cable between the Axe-Fx III and FC controller

FM3 – connect the XLR cable between the FM3 and FC controller

Axe-Fx II – connect the XLR cable. Turn on FASLINK in the I/O menu

MFC-101 – connect the XLR cable. Select the correct port in the MFC settings. Do NOT connect a power supply to the MFC-101 when using FASLINK

Provide power through FASLINK

A FASLINK II connection provides power (from the Axe-Fx III or FM3) to the first connected FC controller.

"The FC-12 uses more power because it has more LCDs. If the cable resistance is too high than there will be excessive voltage drop which could cause booting issues and other problems. Using a cable snake is not recommended because the conductor gauge is small and the resistance will be high. We recommend a good quality dedicated XLR cable. Dim LEDs are an indication that there is excessive voltage drop on the cable. The FC rated voltage is 9-12V but should work down to about 7V. If the snake is 100 ft. of 24 gauge wire then that would put you right at 7V. The FC-12 draws about 1A so Vdrop = 0.025 ohms/ft * 100 ft * 2 conductors * 1A = 5V drop. This is assuming the shield drain has the same resistance as the conductors. So, yeah, 100 ft snake is too long for an FC-12." source

FASLINK adapters for older hardware

The FASLINK XA-1 and XA-2 adapters convert the wiring on older Axe-Fx II and MFC-101 hardware (see above) from Ethernet/Ethercon to XLR. These adapters are "active" (source). They can be bought directly from Fractal Audio's online shop and G66.

The adapters do not support FASLINK II.

More information in the FASLINK Setup Guide

FASLINK adapters.png

XA-1 diagram.png

XA-2 diagram.png